Installation Guide

12
Dishwasher Installation
Printed in China
DISHWASHER WET TEST
(CONT)
• Check to be sure that water enters the dishwasher. If
water does not enter the dishwasher, check to be sure
that water and power are turned on.
• Check for leaks under the dishwasher. If a leak is found,
turn off power at the breaker, and then tighten water
connections. Restore power after leak is corrected.
NOTE: A small amount of water may splash out of
the fill funnel, on the right side of the tub, during the
first use after installation. Splash-out is most likely to
occur if there is air in the water supply line from new
construction or if the valve has been closed for an
extended time.
• Check for leaks around the door. A leak around the
door could be caused by door rubbing or hitting
against adjacent cabinets. Reposition the dishwasher
if necessary. See Step 11.
• Open dishwasher door. Press and hold the Start pad, until
the light next to the pad turns off, to cancel the cycle.
Close dishwasher door. The unit will begin to drain. Check
drain lines. If leaks are found, turn off power at the breaker
and correct plumbing as necessary. Restore power after
corrections are made. See Steps 7 and 8.
• Open dishwasher door and make sure all of the water
has drained. If not, check that disposer plug has been
removed and/or air gap is not plugged. Also check
drain hose to be sure it is not kinked underneath or
behind dishwasher. See Step 8.
• Press Start button once again and run dishwasher through
another cycle. Check for leaks and correct if required.
• Repeat these steps as necessary.
STEP 18
CHECK THE FOLLOWING
• Dishwasher is square and level at both the top and
bottom of the cabinet opening, with no twisting or
distortion of the tub or door.
• All 4 legs of the dishwasher are firmly in contact with
the floor.
• Drain hose is not pinched between the dishwasher and
adjacent cabinets or walls.
STEP 17
REPLACE TOEKICK
• Install toekick insulation by
placing ends of insulation
in left and right brackets.
Insulation should be installed
up under tub.
• Place the inner toekick piece
(with slots) against the toekick
bracket. The slots should
align with toekick.
Tip: Reduce sound from
under the dishwasher. Make sure toekick is against
floor.
• Place larger toekick over the inner piece and install 4
toekick screws.
• Use both toekick pieces for all installation heights.
STEP 19
PRETEST CHECKLIST
Review this list after installing your dishwasher to
avoid charges for a service call that is not covered by
your Warranty.
• Check to be sure power is OFF.
• Open door and remove all foam and paper packaging.
• Locate the Owner’s Manual.
• Read the Owner’s Manual for operating instructions.
• Check door opening and closing. If door does not open
and close freely, check for proper spring adjustments.
If door drops or closes when released, adjust spring
tension. See Step 1.
• Check to be sure that wiring is secure under the
dishwasher, not pinched or in contact with door
springs or other components. See Step 13.
• Check door alignment with tub. If door hits tub, level
dishwasher. See Step 14.
• Check door alignment with cabinet. If door hits
cabinet, reposition dishwasher. See Step 11.
• Check that door spring does not contact water line, fill
hose, wiring or other components. See Steps 10 and 11.
• Verify water supply and drain lines are not kinked or in
contact with other components. Contact with motor or
dishwasher frame could cause noise. See Steps 10 and 11.
• Turn on the sink hot water faucet and verify water
temperature. Incoming water temperature must
be between 120°F and 140°F. A minimum of 120°F
temperature is required for best wash performance.
See “PREPARE HOT WATER LINE”.
• Add 2 quarts of water to the bottom of the dishwasher
to lubricate the pump seal.
• Turn on water supply. Check for leaks. Tighten
connections if needed.
• Remove protective film if present from the control
panel and door.
• Avoid service call charges by ensuring there is an air
gap or drain hose routed through the required 32”
minimum height. See Step 8.
STEP 16
DISHWASHER WET TEST
• Turn on power supply or plug power cord into outlet, if
equipped.
• Select a cycle to run and push the Start button.
• Close dishwasher door. Dishwasher should start.
STEP 18