Installation Guide

WARNING/AVERTISSEMENT
Risk of re or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrot kit. Check for
enclosed wiring and components. / Risque de feu ou électrocution. Les pièces et câbles électriques risquent d’être endommagés lors du perçage
des trous pour l’installation du luminaire à DEL. Veuillez vérier si des câbles et composantes se trouvent derrière la paroi avant de percer.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. / Pour éviter l'endommagement de
câblage ou l'abrasion, ne pas exposer le câblage aux bords de feuilles de métal ou d'autres objets tranchants.
3
Install Center LED Lights
3
• Place a Center LED Light against the back face of the
mullion near the two holes drilled at the top.
• Insert a #6-32 x 1/2-inch sheet metal screw into the top slot
of the Mounting Tab on the Center LED Light and into the
rst hole that was drilled in the center mullion.
• Use a screwdriver to thread the screw into the drilled hole.
• Repeat for the second screw, and for the lower end of the
Center LED Light.
• Refer to the manufacturing manual for door frame to
ensure there are no components contained inside the
mullion that could be drilled through. Use a #6 - 3/4-inch
self-drilling screw to attach the Center LED Light into one
or two of the additional mounting holes located near the
center of the LED Light.
• Refer to wiring diagram on page 5. Connect the red and
black output wires from the LED Light to the red and black
wires on the LED Driver using the twist lock splice wire
connectors provided.
WARNING/AVERTISSEMENT
Risk of electrical shock. Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit
installation. Do not leave any other open holes in an enclosure of wiring or electric components / Risque de choc électrique. Seuls les trous
ouverts indiqués dans les photos et / ou les dessins peuvent être faites ou modiés à la suite du montage du kit. Ne pas laisser autres trous
ouverts dans l'enceinte du câblage électrique ou composants.
• Measure the total width of the mullion, and mark a vertical line half
the total width near the top and bottom of the mullion.
• Prepare for the upper end of the Center LED Light. Mark a horizontal
line a minimum 2 1/8-inches (54 mm) from the top of the mullion,
and another horizontal line 3/8-inch (10 mm) below this line.
• Prepare for the lower end of the Center LED Light.
— For 48-inch LED Lights mark a horizontal line
46 1/4" (1175mm) beneath the rst line drawn for
the top Mounting Tab.
— For 60-inch LED Lights mark a horizontal line
58 3/32" (1476mm) beneath the rst line drawn for
the top Mounting Tab.
— For 67-inch LED Lights, mark a horizontal line
65 15/32" (1663mm) beneath the rst line drawn for
the top Mounting Tab.
• Center the center punch directly at the intersection of the horizontal
lines and the vertical line (top and bottom) and establish a dimple.
• Use power drill and 7/64-inch (2.8 mm) drill bit to drill holes at the
intersection of the vertical and horizontal center line.
2
Total width
of mullion
Half total
width of
mullion
3/8"
(10 mm)
LED Driver
wires - top
For 48-inch LED Lights:
46 1/4" (1175mm)
For 60-inch LED Lights:
58 3/32" (1476mm)
For 67-inch LED Lights:
65 15/32" (1663mm)
Center punch
at intersection
and drill a
7/64-inch (2.8 mm)
hole
Prepare for Installation of
Center LED Lights
LED Driver Leads
Center LED Light
Power Leads
Mounting Tab