Zoneline Engineering Data Manual

12
Auxiliary Control—Aux Set Button
Auxiliary Control Settings
The auxiliary control push button is located behind the room
cabinet, below the control panel. The auxiliary controls come
preset to the modes most desired by customers. However,
the owner is responsible for ensuring the auxiliary controls
are set to the desired function. There are 9 different modes
that can be set using the auxiliary set button.
To change modes:
•PresstheSTOPbutton.
•PressAUXSET(“AU”appearsonthedisplay).
•PresstheMODEbuttononthecontrolpaduntil
the first digit in the display shows the number
corresponding to the mode you are choosing
and the correct HEAT/COOL LED is lit.
•Presstheupordownarrowtochangethemode
setting selection (second digit in the display).
•PresstheMODEbuttontomovetothenextfeature
or the AUX SET button to exit the set up process.
Press “SET”
First Digit
Second Digit
Press “Mode”
Press
/
HEAT
COOL
Smart Fan Cool – Cycle*
Smart Fan Cool – Continue
Press “Mode”
Press
/
HEAT
COOL
Smart Fan Heat – Cycle*
Smart Fan Heat – Continue
Press “Mode”
Press
/
Load Shedding – Off
Load Shedding –On
Press “AUX SET”
First Digit
Second Digit
Press “Mode”
Press
/
Smart Fan
HEAT
COOL
Load Shedding
Sentinel
HEAT
COOL
Constant Fan
Temperature
Limit
HEAT
COOL
Class 2 Mode
Duct Mode
All I2R Mode
Boost Heat
0: 60F-85F
1: 64F-85F
2: 66F-85F
3: 68F-85F
4: 70F-85F
5: 72F-85F
6: 74F-85F
7: 76F-85F
0: 60F-65F
1: 60F-70F
2: 60F-72F
3: 60F-74F
4: 60F-76F
5: 60F-78F
6: 60F-80F
7: 60F-85F
HEAT
COOL
– Off
–On
– Off
–On
–Cycle
– Continue
(AZ61 Only)
(AZ61 Only)
Mode 2—Load Shedding (Central Desk Control)
The default setting for Mode 2 is OFF.
This feature is active only if the unit is connected to a
CDC and the CDC has control. When this mode is on,
only the indoor fan can be turned ON or OFF with the
unit controls. When this mode is off, all operation is
disabled except Heat/Freeze Sentinel (Mode 3).
Mode 1—Smart Fan—Cooling/Heating
The default setting for Mode 1 is as follows:
Cooling: Continuous (ON)
Heating: Cycle (OFF)
Press “AUX SET”
First Digit
Second Digit
Press “Mode”
Press
/
Smart Fan
HEAT
COOL
Load Shedding
Sentinel
HEAT
COOL
Constant Fan
Temperature
Limit
HEAT
COOL
Class 2 Mode
Duct Mode
All I2R Mode
Boost Heat
0: 60F-85F
1: 64F-85F
2: 66F-85F
3: 68F-85F
4: 70F-85F
5: 72F-85F
6: 74F-85F
7: 76F-85F
0: 60F-65F
1: 60F-70F
2: 60F-72F
3: 60F-74F
4: 60F-76F
5: 60F-78F
6: 60F-80F
7: 60F-85F
HEAT
COOL
– Off
–On
– Off
–On
–Cycle
– Continue
(AZ61 Only)
(AZ61 Only)
Auxiliary Set Button
Access
Cover
* Note: In cyclic Cooling Mode, the indoor fan will activate occasionally to
verify air temperature in the room. In cyclic Heating Mode, the fan will
continue to operate for 90 seconds after the heating function has stopped
in order to increase unit efficiency.