Data Sheet

07.13 GFA-1889A
GE Intelligent Platforms Contact Information
Americas: 1 877 429 1553
Global regional phone numbers are listed by location on our web site at
defense.ge-ip.com/avionics-contacts
www.defense.ge-ip.com
©2012 GE Intelligent Platforms, Inc. All rights reserved. All other brands or names are property
of their respective holders. Specifications are subject to change without notice.
R15-USB – RoHS Dual port MIL-STD-1553 USB adapter
Specifications
Physical
• USB Interface Box (4.3” x 5.0” x 1.4” inches)
• 10.5 ounces
Environmental
• Standard operating temperature range:
-40°C to +75°C with 600ft/min air flow
• Rugged (without relays)
• Storage temperature -50°C to +100°C
• Relative humidity with relays: up to 85%
(non-condensing)
• Relative humidity without relays: up to 95%
(non-condensing)
• Optional conformal coating configurations
Software Support
• API - High-level libraries with source code included for
Microsoft
®
Windows
®
, 7 (32 and 64 bit), Vista and XP
• GUI - Optional BusTools/1553 GUI Bus Analysis,
Simulation & Data Logging software
• Standard with IRIG-B Receiver (AM or DC/TTL) and
Generator (DC/TTL)
Connections
• Software selectable transformer or direct coupling
via relays
• 8 Bi-directional Avionics level discretes
Multi-function Operational Modes
• Simultaneous BC
Dual-function Operational Modes
• BM and 31 RTs, or BM and BC
Power (2 channels at 75% duty cycle)
• Will operate with USB power
• External +5V power input provided
On-board Shared RAM
• 2 Mbyte
Timing
• Independent 64-bit, 25ns message time-tagging per
channel
• Time can be programmed via the host or by a 1553
trigger
• All timers can be synchronized to 0 via the host
• Timers can independently use IRIG time
• IRIG-B receiver (AM or DC/TTL) and generator (DC/TTL)r
Bus Controller
• Programmable control over:
- Major and minor frame content and timing
- Inter-message gap times
- Response time-out and late response
• Modify messages, data or setup on the fly
• Insert aperiodic messages into a running BC list
• Multiple data buffers
• Conditional message sequencing based on real-time
message data or status
• Selectable interrupt generation and status messages on
full range of system conditions or all detected errors
• Synchronize BC operation to external time source
Block Diagram
Programmable full error detection/injection available
on BC and RT and full detection available on BM (on a
per word basis)
- Invalid word - Late response
- Bit count error - Early response
- High word - No response
- Low word - Incorrect RT address
- Inverted sync - Parity error
- Manchester
Bus Monitor
• Capture 100% fully loaded bus traffic with:
- Time-tagging - Error status
- Word status - Message status
• Extensive filtering and triggering options
- By individual RT/subaddress
- Transmit, receive or broadcast mode codes
- Internal or external triggering
- Trigger output on user specified data
• Real-time bus playback with RT edit mode
Remote Terminal
• Multiple RT simulation (up to 31 RTs)
• Modify data, status words or setup while card is
running
• Programmable message content (linked message
buffers)
• Selectable interrupts upon multiple conditions
• RT Map Monitoring
Optional Configurations
• 1 or 2 Dual or Multi-function channels
• Optional conformal coating
• Optional Transformer or Direct coupling
• Contact factory for Custom requirements
Ordering Information
R15-USB - 1D MIL-STD-1553 Dual-Function, Single dual-redundant channel, 32-bit FW, USB interface box,
8 Bi-directional discretes, Relay coupled, Fixed voltage with IRIG-B Rec/Gen
R15-USB - 1M MIL-STD-1553 Multi-Function, Single dual-redundant channel, 32-bit FW, USB interface box,
8 Bi-directional discretes, Relay coupled, Fixed voltage with IRIG-B Rec/Gen
R15-USB - 2D MIL-STD-1553 Dual-Function, Two dual-redundant channel, 32-bit FW, USB interface box,
8 Bi-directional discretes, Relay coupled, Fixed voltage with IRIG-B Rec/Gen
R15-USB - 2M MIL-STD-1553 Multi-Function, Two dual-redundant channel, 32-bit FW, USB interface box,
8 Bi-directional discretes, Relay coupled, Fixed voltage with IRIG-B Rec/Gen
BT3-R15-USB-1D MIL-STD-1553 Bus Analyzer bundle (Includes R15-USB-1D hardware and BT-1553 software)
BT3-R15-USB-1M MIL-STD-1553 Bus Analyzer bundle (Includes R15-USB-1M hardware and BT-1553 software)
BT3-R15-USB-2D MIL-STD-1553 Bus Analyzer bundle (Includes R15-USB-2D hardware and BT-1553 software)
BT3-R15-USB-2M MIL-STD-1553 Bus Analyzer bundle (Includes R15-USB-2M hardware and BT-1553 software)
Ordering Options K Suffix = Conformal Coating
R Suffix = No Relays
Optional Software BT-1553 – MIL-STD-1553 Bus analysis and data logging software for Windows
LV-1553 – Lab/View Support for MIL-STD-1553
MIL-STD-1553
XCVR
Cypress
FX2
2 MB
RAM
Xilinx
FPGA
MIL-STD-1553
XCVR
Low-side
Switches
Isolation XFMR
Isolation XFMR
Isolation XFMR
Isolation XFMR
Discrete
Receive
IRIG
Driver
IRIG
Out
Ch 1
Bus A
Ch 1
Bus B
Ch 2
Bus A
Ch 2
Bus B
Discrete
I/O
IRIG
In
IRIG
Receive
USB