Quick Specs

Specification Revised 5/17
PSB9240EF/BL
GE Profile
™
Series 30 in. Single Wall Oven with Advantium
®
Technology
Installation over a GE/Monogram
Warming Drawer:
30”
23-1/2”
25-1/4”
Min.
21”
2” Min.
(3” recommended)
Per warming
drawer
requirement
Construct
Solid Bottom
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
5” min.
from floor
1” min.
above
toekick
PREPARE THE OPENING: The Advantium 240V can
be installed in combination with other GE/Monogram
appliances. Always follow each product's Installation
Instructions to compete the installation.
SINGLE OVEN INSTALL ATION: Order a 30" wide
single oven cabinet or cut the opening in a wall to the
dimensions shown.
* For existing cutouts, a
maximum width of 28-1/2"
is acceptable. If the opening
is slightly wider, secure a
furring strip on each side of
the cutout for securing the
oven.
- Always maintain 36-3/4"
minimum height from
the floor to the cutout in
any single or combined
installation.
- Allow 3/4" to 2-1/8" case
trim overlap on the sides and 7/8" overlap on the
bottom of the opening for all models. The amount
of overlap on the sides depends on the actual cutout
width. Allow 1-1/4" case trim overlap on the top for
models PSB9240 and for models ZSC2200, ZSC2201
and ZSC2202.
- Oven overlaps will conceal cut edges on all sides of
the opening.
PREPARE THE OPENING (CONT.)
When installed over a single oven
or a warming drawer, allow at least
2" between the two openings. This
separation will provide clearance for
bottom overlap of the Advantium 240V
and the other appliance overlaps.
Construct a solid oven floor of 3/8" min.
thick plywood supported by 2 x 4 or 2 x
2 runners on all sides.
- the support must be level and rigidly
mounted, flush with the bottom edge of
the cutout.
* For existing cutouts, a maximum width
of 28-1/2" is acceptable. If the opening is
slightly wider, secure a furring strip on each
side of the cutout for securing the oven.
NOTE: Additional clearances between
the cutouts may be required. Check to be
sure the oven supports above the Warming
Drawer location do not obstruct the
required interior depth and height. See
Warming Drawer installation instructions
for details.
INSTALLATION OVER A GE/
MONOGRAM OVEN AND
WARMING DRAWER:
* For existing cutouts, a maximum width
of 28-1/2" is acceptable. If the opening
is slightly wider, secure a furring strip on
each side of the cutout for securing the
oven.
NOTE: Additional clearances between the
cutouts may be required. Check to be sure
the oven supports above the Warming
Drawer location do not obstruct the
required interior depth and height. See
Warming Drawer installation instructions
for details.
CAUTION: For personal safety, the
mounting surface must be capable of
supporting the cabinet load, in addition
to the added weight of this approximate
80-pound oven and 30-pound drawer, plus
additional oven loads of up to 50 pounds
or a total weight of 160 pounds.
30”
23-1/2”
25-1/4”
Min.
21”
Construct
Base
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
5” min.
from floor
1” min.
above
toekick
PREPARATION WITH AN ACCESSORY DRAWER
Warming Drawer:
Construct Solid
Bottom Min.
3/8” Plywood
Supported by
2x4 or 2x2
Runners all
Four Sides
30”
23-1/2”
21”
2” Min.
Per Oven
Requirement
Per warming drawer requirement
2” Min.
(3” recommended)
25-1/4”
Min.
5” min.
from floor
1” min.
above
toekick