Installation 30” Sealed Gas Cooktop Instructions JGP329, JGP333, JGP940, PGP943 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca ~ IN THE COMMONWEALTH MASSACHUSETTS: OF e This product must be installed by a licensed plumber or gas fitter. e When using ball-type gas shut-off valves, they shall be the T-handle type. ¢ A flexible gas connector, when used, must not exceed 3 feet.
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on the rating plate. We recommend you have the electrical wiring and hookup of your cooktop connected by a qualified electrician. After installation, have the electrician show you where your main cooktop disconnect is located.
Installation Instructions PRE-INSTALLATION CHECKLIST When preparing cooktop opening, make sure the inside of the cabinet and the cooktop do not interfere with each other. Remove Installation Instructions from literature pack and read them carefully before you begin. (See section on preparing the opening.) Be sure to place all literature, Use and Care, Installations, etc. in a safe place for future reference.
Installation Instructions PREPARING THE OPENING [4] MAINTAIN THE FOLLOWING MINIMUM CLEARANCE DIMENSIONS [4 | RECOMMENDED GAS SUPPLY LOCATION FROM BACKWALL 1” Min. From Backwall 13” MAX. Depth of unprotected overhead cabinets 6” MIN. clearance from cutout to side wall on the right of the unit 30” MIN. clearance from countertop to unprotected overhead surface a> 3-3/4" MIN. clearance from? cutout to side wall on the | He sn Op. A Recommended gas supply location 13-4/4" go 78" MIN.
Installation Instructions INSTALLING THE COOKTOP UNIT [4] LOCATE ELECTRICAL OUTLET AND GAS SHUT-OFF VALVE BENEATH CABINET NEVER REUSE OLD CONNECTORS WHEN INSTALLING THIS UNIT [4] LOCATE MOUNTING Remove the hold down brackets from the literature package. of cv \ shutoff PARTS = 1) @
Installation Instructions INSTALLATION—GAS CONNECTIONS [4] PROVIDE ADEQUATE GAS SUPPLY [3] INSTALL REGULATOR ONTO BURNER BOX BOTTOM This cooktop is designed to operate on natural gas at 4” of water column manifold pressure and 7" of water column (W.C.) supply pressure. It is shipped from the factory set for natural gas.
Installation Instructions [5 | CHECK FOR LEAKS Before testing for leaks, make sure all burner knobs are in the OFF position. After connecting the cooktop to gas, check system for leaks with a manometer. If a manometer is not available, turn the gas supply on to the cooktop and use a liquid leak detector at all joints and connections to check for leaks. [6] INSTALLATION OVER BUILT-IN OVEN See built-in oven installation for complete installation instructions. 5" To Center of 2" Dia.
Installation Instructions INSTALLATION—ELECTRICAL CONNECTIONS AWARNING — Disconnect all electrical power at the main circuit breaker or fuse box before installing. [4] EXTENSION CORDS Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.
Installation Instructions [4] USAGE SITUATIONS WHERE APPLIANCE POWER CORD WILL BE DISCONNECTED INFREQUENTLY For 15 amp circuit only. Do not use an adaptor on a 20 amp circuit. Where local codes permit, a TEMPORARY CONNECTION may be made to a properly grounded 2-prong wall receptacle by the use of a UL-listed adaptor available at most hardware stores. The larger slot in the adaptor must be aligned with the large slot in the wall receptacle to provide proper polarity in the connection of the power cord.
Installation Instructions COOKTOP BURNERS [4] ASSEMBLING THE COOKTOP BURNERS Make sure the pins in Burner cap the burner heads match the burner base indentations and that they are properly seated in them by rotating the heads until they are level. The electrode of the spark igniter is exposed. Be careful not to push any cooktop controls while the top of the burner is removed. Do not remove the top or touch the electrode of any burner while another burner is turned on. Electrical shock might result.
Installation Instructions [2] CHECK IGNITERS [4] THE BURNER FLAMES Operation of the electric igniters should be checked after the cooktop and supply line have been carefully checked for leaks and the cooktop has been connected to the electrical power. Turn each burner on. Flames should be blue in color with no trace of yellow. The burner flames should not flutter or blow away from the burner. The flame should be no less than 1/4” on the lowest setting and no greater than 1-1/2” on highest setting.
Installation Instructions OPERATION CHECKLIST Make sure all controls are left in the OFF position. Check to be sure the cooktop is in the UNLOCKED position (on models so equipped). [0] Make sure the flow of air to and from the le] When ordering parts, always include the serial number, model number and a code letter to ensure proper replacement parts. cooktop is unobstructed. The serial plate for your cooktop is located on the bottom of the burner box.
Installation Instructions MAKING THE LP CONVERSION IF SOLD OUTSIDE THE U.S. AND TOOLS YOU WILL NEED FOR LP CONVERSION CANADA: A.WARN ING: if you wish to use this product with Liquefied Petroleum (LP) gas containing greater than 10% butane, you must purchase a butane conversion kit. To order, please call 1.888.664.8403 or =o E=Ce——=a mee Phillips-Head 7mm Nutcriver Screwdriver 1.787.276.4051. Model JGP940 JGP333& PGPo42 Butane Kit # WB28T10228 WB28T10283 JGP329 WB28T10234 —_ No.
Installation Instructions MAKING THE LP CONVERSION (CONT.) [3] CHANGE COOKTOP BURNER [3] CHANGE COOKTOP BURNER ORIFICES (CONT.) ORIFICES Remove the top grates, burner caps, and burner heads. Remove the spark NOTE: On most burners, the orifices have a springRetainer Ring loaded retaining ring around the hex head to hold the orifice in the nut driver during installation and removal. A slight amount of force is required to push the nut driver down over the ring.
Installation Instructions [3] CHANGE COOKTOP BURNER ORIFICES (CONT.) [pb] Locate the LP/Propane orifices shipped inside the literature package. They will have a digit number and the letter “L” on the side. (Important: Save the orifices removed from the appliance for future use.) Model | Rear Left} Front Left Front Right Burner | Burner Burner Each orifice will show a series of engraved marks, (1, I, Hl, X or none}, JGP329 iI iI ll located on the top. IGP940 ill mT \ JGP333] PGP943 Ill I
Installation Instructions MAKING THE LP CONVERSION (CONT.) [4] ADJUST BURNER FLAMES [b>] Make the adjustment by slowly turning the screw until flame appearance is correct. Turn all burners full on and check the flames. Note: Some models may contain a silicone shield which covers the valve switch and access hole. A flashlight may be required to locate the access hole. To access the valve adjusting screw, push the screwdriver through this shield.
Installation 30” Sealed Gas Cooktop Instructions JGP329, JGP333, JGP940, PGP943 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca ~ IN THE COMMONWEALTH MASSACHUSETTS: OF e This product must be installed by a licensed plumber or gas fitter. e When using ball-type gas shut-off valves, they shall be the T-handle type. ¢ A flexible gas connector, when used, must not exceed 3 feet.
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on the rating plate. We recommend you have the electrical wiring and hookup of your cooktop connected by a qualified electrician. After installation, have the electrician show you where your main cooktop disconnect is located.
Installation Instructions PRE-INSTALLATION CHECKLIST When preparing cooktop opening, make sure the inside of the cabinet and the cooktop do not interfere with each other. Remove Installation Instructions from literature pack and read them carefully before you begin. (See section on preparing the opening.) Be sure to place all literature, Use and Care, Installations, etc. in a safe place for future reference.
Installation Instructions PREPARING THE OPENING [4] MAINTAIN THE FOLLOWING MINIMUM CLEARANCE DIMENSIONS [4 | RECOMMENDED GAS SUPPLY LOCATION FROM BACKWALL 1” Min. From Backwall 13” MAX. Depth of unprotected overhead cabinets 6” MIN. clearance from cutout to side wall on the right of the unit 30” MIN. clearance from countertop to unprotected overhead surface a> 3-3/4" MIN. clearance from? cutout to side wall on the | He sn Op. A Recommended gas supply location 13-4/4" go 78" MIN.
Installation Instructions INSTALLING THE COOKTOP UNIT [4] LOCATE ELECTRICAL OUTLET AND GAS SHUT-OFF VALVE BENEATH CABINET NEVER REUSE OLD CONNECTORS WHEN INSTALLING THIS UNIT [4] LOCATE MOUNTING Remove the hold down brackets from the literature package. of cv \ shutoff PARTS = 1) @
Installation Instructions INSTALLATION—GAS CONNECTIONS [4] PROVIDE ADEQUATE GAS SUPPLY [3] INSTALL REGULATOR ONTO BURNER BOX BOTTOM This cooktop is designed to operate on natural gas at 4” of water column manifold pressure and 7" of water column (W.C.) supply pressure. It is shipped from the factory set for natural gas.
Installation Instructions [5 | CHECK FOR LEAKS Before testing for leaks, make sure all burner knobs are in the OFF position. After connecting the cooktop to gas, check system for leaks with a manometer. If a manometer is not available, turn the gas supply on to the cooktop and use a liquid leak detector at all joints and connections to check for leaks. [6] INSTALLATION OVER BUILT-IN OVEN See built-in oven installation for complete installation instructions. 5" To Center of 2" Dia.
Installation Instructions INSTALLATION—ELECTRICAL CONNECTIONS AWARNING — Disconnect all electrical power at the main circuit breaker or fuse box before installing. [4] EXTENSION CORDS Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.
Installation Instructions [4] USAGE SITUATIONS WHERE APPLIANCE POWER CORD WILL BE DISCONNECTED INFREQUENTLY For 15 amp circuit only. Do not use an adaptor on a 20 amp circuit. Where local codes permit, a TEMPORARY CONNECTION may be made to a properly grounded 2-prong wall receptacle by the use of a UL-listed adaptor available at most hardware stores. The larger slot in the adaptor must be aligned with the large slot in the wall receptacle to provide proper polarity in the connection of the power cord.
Installation Instructions COOKTOP BURNERS [4] ASSEMBLING THE COOKTOP BURNERS Make sure the pins in Burner cap the burner heads match the burner base indentations and that they are properly seated in them by rotating the heads until they are level. The electrode of the spark igniter is exposed. Be careful not to push any cooktop controls while the top of the burner is removed. Do not remove the top or touch the electrode of any burner while another burner is turned on. Electrical shock might result.
Installation Instructions [2] CHECK IGNITERS [4] THE BURNER FLAMES Operation of the electric igniters should be checked after the cooktop and supply line have been carefully checked for leaks and the cooktop has been connected to the electrical power. Turn each burner on. Flames should be blue in color with no trace of yellow. The burner flames should not flutter or blow away from the burner. The flame should be no less than 1/4” on the lowest setting and no greater than 1-1/2” on highest setting.
Installation Instructions OPERATION CHECKLIST Make sure all controls are left in the OFF position. Check to be sure the cooktop is in the UNLOCKED position (on models so equipped). [0] Make sure the flow of air to and from the le] When ordering parts, always include the serial number, model number and a code letter to ensure proper replacement parts. cooktop is unobstructed. The serial plate for your cooktop is located on the bottom of the burner box.
Installation Instructions MAKING THE LP CONVERSION IF SOLD OUTSIDE THE U.S. AND TOOLS YOU WILL NEED FOR LP CONVERSION CANADA: A.WARN ING: if you wish to use this product with Liquefied Petroleum (LP) gas containing greater than 10% butane, you must purchase a butane conversion kit. To order, please call 1.888.664.8403 or =o E=Ce——=a mee Phillips-Head 7mm Nutcriver Screwdriver 1.787.276.4051. Model JGP940 JGP333& PGPo42 Butane Kit # WB28T10228 WB28T10283 JGP329 WB28T10234 —_ No.
Installation Instructions MAKING THE LP CONVERSION (CONT.) [3] CHANGE COOKTOP BURNER [3] CHANGE COOKTOP BURNER ORIFICES (CONT.) ORIFICES Remove the top grates, burner caps, and burner heads. Remove the spark NOTE: On most burners, the orifices have a springRetainer Ring loaded retaining ring around the hex head to hold the orifice in the nut driver during installation and removal. A slight amount of force is required to push the nut driver down over the ring.
Installation Instructions [3] CHANGE COOKTOP BURNER ORIFICES (CONT.) [pb] Locate the LP/Propane orifices shipped inside the literature package. They will have a digit number and the letter “L” on the side. (Important: Save the orifices removed from the appliance for future use.) Model | Rear Left} Front Left Front Right Burner | Burner Burner Each orifice will show a series of engraved marks, (1, I, Hl, X or none}, JGP329 iI iI ll located on the top. IGP940 ill mT \ JGP333] PGP943 Ill I
Installation Instructions MAKING THE LP CONVERSION (CONT.) [4] ADJUST BURNER FLAMES [b>] Make the adjustment by slowly turning the screw until flame appearance is correct. Turn all burners full on and check the flames. Note: Some models may contain a silicone shield which covers the valve switch and access hole. A flashlight may be required to locate the access hole. To access the valve adjusting screw, push the screwdriver through this shield.
