Specification

PEP9030DT
GE Profile
™
30" Built-In Touch-Control Electric Cooktop
For answers to your Monogram, GE Café
™
, GE Profile
™
or GE Appliances
product questions, visit our website at geappliances.com or call
GE Answer Center
®
Service, 800.626.2000.
ADA
COMPLIANT
Listed by
Underwriters
Laboratories
Specification Revised 10/22
To insure accuracy, it is best to make a
template when cutting the opening in the counter
Cooktop
29-3/4"
20-7/8"
19-1/4"
28-1/16"
19-5/8" to
19-3/4"
28-1/2" to
28-5/8"
2-1/2" MIN.
Required
1-3/4" MIN.
to rear wall
3-3/4" at front of unit and
5-13/16" at conduit location
13" MAX. depth of unprotected
overhead cabinets
30" MIN. Clearance from
countertop to unprotected
overhead surface
2" MIN. Clearance
from cutout to
nearest vertical
wall or cabinet on
left side of the unit
below the 15" MIN.
clearance height.
1 1/2" MIN. (30") and
2" MIN. (36") Clearance
from cutout to nearest
vertical wall or cabinet
on right side of the unit
below the 15" MIN.
clearance height.
30" MIN. for
30" cooktop
15" MIN. height
from countertop
to nearest cabinet
(including light rails)
on both sides of
cooktop
IMPORTANT: Requires a 5" free area between
the bottom of the cooktop to any combustible
material, i.e., shelving. Free area not required
when installing wall oven underneath cooktop.
Refer to installation instructions. Requires a 15"
minimum from cooktop to adjacent overhead
cabinets. Units are furnished with a 48" flexible
armored cable.
NOTE: 30" Ribbon cooktops are approved for
use over select GE 27" and GE 30" Single Wall
Ovens and Warming Drawers. Refer to cooktop
and wall oven/warming drawer installation
instructions packed with product for current
dimensional data. If installed with a GE Telescopic
Downdraft System, consult both the cooktop
and downdraft installation instructions packed
with product before installing. Cooktop gas/
electric supply may need to be re-routed to
install downdraft. The countertop cutout requires
23-1/2" minimum flat countertop surface and 25"
minimum total countertop depth. In addition,
other clearances to front edge of the countertop
must be considered. Before installing, consult
installation instructions packed with product
for current dimensional data.
CUTOUT FILLER TRIM KIT: A filler trim kit is
available for use if your countertop cutout is
larger than the dimension shown, up to 29-13/16"
x 20-7/16". Order JXTR32B for black or JXTR32W
for white, to reduce the cutout opening for
installation of this cooktop. These kits may be
ordered from your GE Appliances Dealer.
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
APPROXIMATE COOKING DIMENSIONS
VOLTAGE (60HZ AC) 240V 208V
CONNECTED LOAD (MAX.) 9.5kW 7.1kW
CURRENT DRAW (MAX.) 39.6 Amps 34.1 Amps
RECOMMENDED CIRCUIT BREAKER
†
40 Amps 40 Amps
†
NOTE: Check local codes for required breaker size.
2-1/2" MIN
From front edge
of countertop to front
edge of cooktop cutout
31-1/4" MIN
From top surface
of countertop to
top surface of
wall oven support
platform
INSTALLATION ABOVE A WALL OVEN
INSTALLATION ABOVE A WALL OVEN