LP Conversion JGSS61
(A) Soft blue flames—
Normal for natural gas
(B) Yellow tips on 
outer cones—
Normal for propane gas
BURNER OUTPUT RATINGS: BTU/HR
Propane Gas 10” W.C.P.
BURNER
BTU 
RATE
ORIFICE 
SIZE (mm) COLOR MARKING
LF 15,000 0.045 Orange/Silver 114L
LR 5,000 0.026 Red/Yellow 66L
RF 15,000 0.045 Orange/Silver 114L
RR 9,500 0.0365 Orange/Light Blue 92L
Broil 13,500 0.042 Grey 042L
Bake 16,000 0.047 Orange 0.047
To adjust your range for use with propane gas, follow these 
instructions:
1. Disconnect all electrical power, at the main circuit breaker or 
fuse box.
6KXWRႇWKHJDVVXSSO\WRWKHUDQJHE\FORVLQJWKHPDQXDO
VKXWRႇYDOYH
CONVERTING THE PRESSURE REGULATOR CONVERTING THE COOKTOP BURNERS
A. Remove the top grates, burner caps and burner heads. 
B. Using a 7 mm or 9/32” nut driver, remove the top burner 
RUL¿FHV7KHVHPD\EHDFFHVVHGWKURXJKWKHEXUQHU
opening in the base.
&5HPRYHWKHSURSDQHRUL¿FHVIURPWKHER[SURYLGHG7KH
SURSDQHRUL¿FHVKDYHWKHOHWWHU³/´RQWKHWRS
 To aid in identifying the proper location for the propane 
RUL¿FHVGXULQJFRQYHUVLRQIURP1DWXUDO*DVWR3URSDQH
Gas, color codes have been added to the side or top of the 
RUL¿FH6HHWKHFKDUWEHORZ(DFKRUL¿FHPD\DOVRVKRZD
series of engraved marks (I, II, III . . .) located on the top.
Remove the warming drawer and panel behind drawer. The 
pressure regulator is located in the lower, left hand rear corner 
of the range as viewed from the front.
 1.  Use an adjustable wrench to unscrew the hex-nut cap 
from the pressure regulator.
 &RPSOHWHO\UHPRYHWKHSURWHFWLYHSODVWLFFDSRႇWKH
threaded metal cap.
 3.  Turn the metal cap so the type of gas being converted to 
is displayed and replace the protective plastic cover.
 4.  Screw the hex-nut cap back into the regulator. 
(Do not over tighten)
TOOLS REQUIRED:
• Adjustable wrench
•  Socket wrench with 
1/2” socket and extension
•  3KLOOLSVKHDGVFUHZGULYHU
•  Flat bladed screwdriver 
(blade approximately 
3/32” across)
•  Nut drivers: 1/4”, 9/32” 
or 7mm
3UHVVXUH5HJXODWRU Gas Valve
PROPANE CONVERSION INSTRUCTIONS
PROPANE
NAT
Rotate cap counter-
clockwise to loosen
Cap assembly
Regulator style A
NOTICE:
6DYHWKHVHRUL¿FHVIRUIXWXUHFRQYHUVLRQEDFNWRQDWXUDOJDV
WARNING
 Do not operate the cooktop or oven 
burners of this range when using propane (bottled) gas 
EHIRUHFRQYHUWLQJWKHSUHVVXUHUHJXODWRUDQGEXUQHURUL¿FHV
for propane gas use. Failure to do so could cause high 
ÀDPHVDQGWR[LFIXPHVZKLFKFDQUHVXOWLQVHULRXVLQMXU\
7KHSUHVVXUHUHJXODWRUDQGWKHEXUQHURUL¿FHVDUHVHWIRU
natural gas. To use propane gas, the regulator and burner 
RUL¿FHVPXVWEHFRQYHUWHG
7KHSURSDQHRUL¿FHVIRUWKHFRRNWRSEXUQHUVDUHVKLSSHGRQ
the back of the range in the location shown.
',QVWDOOWKHSURSDQHRUL¿FHVLQWKHLUSUHFLVHORFDWLRQV
7RSUHYHQWOHDNDJHPDNHVXUHWKHRUL¿FHVSXGVDUHVHFXUHO\
screwed into the gas supply tubes.
(,QVWDOOWKHROGRUL¿FHVSXGVLQWRWKHPHWDOER[RUEUDFNHW
along with these instructions, and replace onto the back of the 
range for possible future conversion.
Round burner
Burner cap
Burner head
Base
2UL¿FHORFDWHG
through this 
opening
3URSDQH&RQYHUVLRQ.LW
PROPANE CONVERSION INSTRUCTIONS
31-2000969 Rev. 0 09-21 GEA
JGSS61
LR
LF
RR
RF
Propane
Red/Yellow
Propane
Orange/Light Blue
Propane
Orange/Silver
Propane
Orange/Silver
95
III
Denotes 0.95mm Orifice size opening
Denotes LP (Propane)
CHECK SURFACE BURNERS
3XVKDQGWXUQDNQREWRWKH/,7(SRVLWLRQ$FOLFNLQJVRXQG
indicates proper operation of the ignition system. When lighting 
DQ\EXUQHUVSDUNVZLOODSSHDUDWDOOEXUQHUVEXWJDVÀRZV
from only the one selected. Once air is purged from the supply 
line, burner should light within 4 seconds. After burner lights, 
URWDWHWKHNQRERXWRIWKH/,7(SRVLWLRQ7U\HDFKEXUQHULQ
succession until all burners have been checked.
Quality of Flames 
'HWHUPLQHWKHTXDOLW\RIÀDPHVYLVXDOO\1RUPDOEXUQHUÀDPHV
should look like (A) or (B).
/RQJEULJKW\HOORZÀDPHVDUHQRWQRUPDO1RUPDOÀDPHVPD\
show signs of an orange tint when well heated or signs of 
ÀLFNHULQJRUDQJHGXHWRSDUWLFOHVLQWKHJDVRUDLU
WARNING
   Explosion Hazard
Death or serious injury can result from failure to follow 
these instructions.
• Service by a qualified service technician only.
• Shut off gas supply and disconnect power before servicing.
• Reconnect all grounding devices after service.
• Replace all parts and panels before operating.


