Installation guide

CARTRIDGE SPECIFICATIONS
Performance Data
This system has been tested according to NSF/ANS] 42
fi)r tile reduction of tile substances listed belong: Tile
concentration of tile indicated subst;mces in water
entering the system was reduced to a concentration
less than or equal to tile pemlissible limit fi)r water
leaving the system, as specified in NSF/ANS] 42.
Additional Replacement Filter
I_XH_YS_CFilter" could be used as a replacement filtex;
FXHTCCartridge
Substance
Standard 42
Chlorine: Taste and Odor
TestConditions
FlowRate:3gpm(11.4Lpm)
pH:7.5_+1
InletPressure:60PSi(4.1bar)
InfluentChallenge Reduction
Concentration Requirements
2.0mg/L+lO% _>50%
OeeratinuReauffements
Average
Reduction
95.5%
Pressure:30 125 psi (2.1 6.9 bar)
Turbidity:5 NTUMax.
Temperature:40°F IO0°F14.4'_C37.7°C)
Temperature:68°F_+5°F(19.8°C_+2.5°C) Capacity:5,000gallons(18,927L)or3 months
T_stingwasperformed understandardlaboratoryconditions,actealpeffornlancemayvary
FXHSCCartridge
GE Model Function Life Construction
FXHSC Sediment* 3 months/ Pleated
30 Micron* 24,000gallons
_Basedon manefacturer'sinternal testing
OperatinqGuidelines
Minimum MaximumSupplyWater Pressure:20 125psi
Minimum MaximumSupplyWaterTemperatures:40°FIOO°F
Filter Cartridge Replacement
You should change _om" filter _dlen the _<ater flo_ is noticeabl) reduced or at least everx 3 months.
_] Turn off _ater to filtel: _ ater must be shut off fl'om
aIl Hpstl'eaIll val_ e.
[_ Press the red pressm'e release button to release
pI'esst II'e,
[3] Unsclew the filter canister and discard used filte_:
_sh tile filter canister with mild soap and watel:
0o not use harsh cleaners or hot water:
[_] Inspect tile filter canister O-ring. Make sm'e it is
lightl) lubricated with clean f()_)d grade silicone
grease (silicone grease is a_;dlable through GE
Paxqts and Service: 1.800.626.2002, part number
WS60XI0005). Be stlre tile o-ring is seated in tile
groove. It is recommended that you replace tile
O-ring if it is damaged.
@Place a ne_ tilter cartridge into tile c;miste_;
maldng sm'e it is centere(1 and complete]} seated
on tile bottom seal.
@Reinstall tile filter canister to tile unit. Use tile
canister _rench to tighten the canistel: DO NOT
OVERTIGHTEN.
[_ Slowl} turn on water to tile filter b} using tile
upstream sh ut-off valx e.
] Press tile red pl'esstll'e release bIlttOll to I'en/o*,e
trapped ail:
[_ dMter installation, flush tile catq:ficlge for
10 mimltes, wait one holm then flush again
fin" lO minutes before using the water:
Remote timer
€
Red pressure _..__
release button
[ I_'_ Head
Filte[
cartn _-_O-ring seal
/_ l/ U__'''_ Filter ca°ister
I _ Turn
I I counterclockwise
Turn _ i _ .
_l:c:_:_s\; _ to t,ghteo
canister
STEP-BY-STEP INSTALLATION INSTRUCTIONS
InstallationOverview
NOTE:Be sure to allow a minimum space of 1½"-2" under
the filter for removing the sump to change the cartridge.
Mounting
bracket
Ferrule
Hexnut
Fi_ing
Hex nut
Ferrule
Fittin,
t
Recommended
shut-offvalve
Canister
Typical installation
Recommended
shut-offvalve