Installation guide

INSTALLATION INSTRUCTIONS
Heavy Duty Water Filtration System--GNWH38F
SAFETY PRECAUTIONS
Check with your state and local public works department for
phnnbing and sanitation codes. You must tollow these guidelines
as you install the Heavv Due,' _hter Filtration System. Using a
qualified installer is recommended.
Be sure tile water supply confl)m_s with tile Performance Data.
If tile water supply conditions are tmknown, contact yore"
nmlficipal water colnpan>
^..WARNING:D,,.or.se,,..,watert,at
microbiologically tmsate or ot unknown qualiQ' without
adequate disintection befi)re or after the system.
It is highly recommended that a water shut-off wflve be placed
directly upstream ot your household filtex:
PROPER INSTALLATION
This Heavy Duty Water Filtration System must be properly installed and located in accordance with the Installation Instructions
before it is used.
Checkwith yeurlocalpublicworks departmentferplumbingcodes.
YoumustfollowtheirguidesasyouinstafltheHeavyDutyWater
FiltrationSystem.
Usethe HeavyDutyWaterFiltrationSystemonapotable,safe-to-
drink,homeCOLDwatersupplyonly.Thefiltercartridgewill not
purifywaterormakeunsafewatersafetodrink.DONOTuseon
HOTwater(100°1:max).
ProtecttheHeavyDutyWaterFiltrationSystemandpipingfrom
freezing.Waterfreezingin thesystemwill damageit.
YourHeavyDutyWaterFiltrationSystemwill withstandupto
100psiwaterpressure,ffyourhousewater supplypressureis
higherthan 100psiduringtheday(itmayreachhigherlevels
atnight),installapressurereducingvalvebeforethe system
isinstalled.
Do not install on HOT WATER.Tile temperature of tile water
supply to tile Heavv Duty _4'ater Filtration System must be
between tile minimum of 40°F and tile maximum ot 100°E
See the FilterCartridgeLifesecd(m.
Do notinstall the Heavv Dull,' _MKer Filtration System using
copper solder fittings. Tile heat fl'om tile soldering process
will damage tile unit.
If making a soldered COl)per installation, do all sweat soldering
before c(mnecfing pipes to tile s)_stem. Torch heat will damage
plastic parts.
a. WARNING:D,s,ardal,...se lpartsa,.ll'ackaging,,
illatexJa] alter instnllation. Si/lall parts rei/laining alter instnllation
could be a choke hazard.
Do not install filter in an outside location or anywhere it will be
exposed to starlight.
RF_]SSORIES FOR INSTALLATION
[] 2 Ac!justable wrenches
[] Pipe cutter
[] Ruler or tape measure
[] Cordless &-ill
[] File
[] Eme W paper
[] Screwdriver
Optlbna/accessoriesareavalTab/e(VL_a,MasterCardorDL_covercardsaccepted)
by vl:_itl)_gour Webs/reat ge.comor fromPartsandAccessories,ca//
800626.2002(I1S,) or8011663.6060(Canada}
CONTENTS INCLUDED WITH PRODUCT
[] Filter system (filter; head and canister)
[] Product literature
[] Canister wrench
[] Timer and battel-ies
[] Motmting bracket
[] D_ur 5/16" Hex-head scre_vs and fi*ur 5/16" Hex washe>head
screws
[] 2 sets of fittings, ferrule and nut to connect 1" tbmale NPTF
threads on filter housing to 3/4" copper plumbing
[] 2 Ui.-appro\vd grounding clamps and a #6 AWG grounding wire
[] \'\lfite sealing rope
[] FXHTC (_hlorine: Taste and (-)do* filter carh-idge
_S_ NWH38FistestedandcertifiedbyNSFInternational
againstNSF/ANSIStandard42with cartridgeFXHTC
forthe reducton of Chor ne:TasteandOdor.
184D1064P001 (ll-4)5,IR) 49-50125-1
ge.com
(;ENERAI, EI£CTRIC COMPANY, Appliance Park, i,ouisville, KY40225
1

Summary of content (8 pages)