Installation guide

Installation Instructions
CARTRIDGE SPECIFICATIONS
Performance Data - Filtration Sgstem GXULQ Using Filter GXULQR
• ThisSystemhasbeentestedaccordingto NSF/ANS142and53for the reductionof the substanceslistedbelow.Theconcentrationof the
indicatedsubstancesinwaterenteringthe systemwasreducedto a concentrationlessthanor equalto the permissiblelimitfor waterleaving
thesystem,asspecifiedinNSF/ANS142and53.
• Actualperformancemayvarywith localwaterconditions.
• Donotusewithwaterthat ismicrobiologicallyunsafeor withwaterof unknownqualitywithoutadequatedisinfectionbeforeor after
the system.
USEPA Influent
Parameter MCL Challen_te Concentration
Chlorinetaste and odor -- 2,0 mg/L _+10%
Particulate Class I
partices 0 5to <lum** - ->i0000 porticles/mL
USEPA Influent
MCL Challen_te Concentration
1 NTU*** 11 ± 1 NTU***
Parameter
Turbidity
*Tested using a flow rate of 2 gpm (7,6 I/min); pressure of 60 psrg;
pH of 75 _+0,5;temp. of 68° _+5°F (20° _+3°C)
**Measurement in particles/mL Particles used were 0.5-1 microns.
***NTU--Nephelometric Turbidity Units
Standard No. 42: Aesthetic Effects
Influent Effluent
Avera_/e Avera_te Maximum
1.9 mg/L <005 mg/L O.O5 mg/L
10333333 #/mL 20,500 #/mL 41,0OO #/mL
Standard No. 53: Health Effects
Effluent
Influent
Averacle Avera_te
11.O0 NTU 0,1 NTU
% Reduction
Avera_te Minimum
>974% 974%
998% 996%
Reduction
Requirement
->50%
->85%
% Reduction
Reduction
Maximum Average Minimum Requirement
O1 NTU 991% 991% O.5NTU
Operating Specifications
Capacity: certified for up to 2000 gallons (7,571 I);up to six months
Pressure requirement: 35-100 psi (2,8-6 9 bar}
Temperature: 33°-1OO°F(0,6°-38°C)
STEP-BY-STEPINSTALLATION INSTRUCTIONS
Installation Overview
NOTE: Be sure to allow o minimum space of11/8"-2"
under the system for removing the filter cartridge.
lf b!ou have copper tubing with 3/8" compression fittings,
gou'tt need to follow Step 3 Option B (Optional Installation).
3/8" x 1/2" Push to
Connect Ado Filter Head/
Bracket
Tubing
insert
Hex nut
Ferrule
Shut-Off Valve
HOT COLD
IN Filter
Cartridge
HOT COLD Optional installation
FILTER CARTRIDGE REPLACEMENT
Replacement Filter Canister/Estimated Replacement Casts
GXULQR--Replacement filter canister $29-34
For replacement parts, call toll-free 800.626.2002 (U.S.),
800.663.6060 (Canada-English), 800.361.3869 (Canada-French)
TO REMOVEFILTER:
• Turn filter 1/4 turn to the left. The top surface of
the filter will move away from the bottom of the
head. Pull the filter down to remove.
FILTER CARTRIDGE REPLACEMENT (cont.)
TO REPLACEFILTER:
[] Push filter into the filter head/bracket. Turn filter
1/4 turn to the right until it stops. The top surface
of the filter will be flush with the bottom of the filter
head/bracket when fully installed.
NOTE:When correctly installed, the label will face out.
[] Turnon the cold water faucet to flush the filter for
5 minutes to remove air.
[] Changethe batteries in the timer.
NOTE: Remove the water in the line to minimize the water released
duringfiltercartridgereplacement.Turnoff thecoldwatersupplbJ
valveandturnon thefaucetfor5seconds.
INSTALLING THE SYSTEM
ITI SELECT A LOCATION
[] Select a location for the sgstem that is:
• Protected from freezing.
• Notexposed todirect sunlight.
[] Select and murk a location under the sink that allows
access for u filter cartridge change. SeeSection 4,
The sgstem can be mounted verticallg or horizontallg.
DO NOT MOUNT THESYSTEMUPSIDEDOWN.
DISCONNECT COLD WATER SUPPLY
[] Remove items from under the sink. Place a
bucket and some towels under the sink to collect
any water that may run out when disconnecting
the water supply lines.
[] Turn offthe cold water supply valve and remove
the existing water supply tubing and fittings.
NOTE: For copper tubing, leave the 3/8" compression
fitting on the faucet stem. Go to Step 3, Option B.