Manual

Step°by°step installation instructions,
Programmingthe Control
lUVEL[_ !!_t'!_tt_!1 I
IP"ESE"TTmME \\
F-_-_ I_ _ tU L-I I I HARDNESS \\
[_I !-IO I JFIECHARGE,,_,4E \_
CONTROL SKIT1NGS REQUIRED _pon b_st;dk_tio_ am! after a_
exte_(led power outage,
NOTES:
_¢WHEN THE TI{_NSFOI_IER IS PI,UGGED INTO THE
EI,ECTR/(_M, OUTLET, 12:00 PM (fl_tshing), _md _m arro_ _ is
(tisl)la?_d next to PRESENTTIMEon the lintel)late decal. Y]_e bhle
indicator light will also flash. Program the conm)l as instructed
belo_.
If E I
OO -- -is flasl_lg, use the UP • button to set the correct F or
H code as tollows: H39 tor GXSH39E or H45 tbr GNSH45E. If you
pass b_ the corl_ct code munber, tire the DOWN • button. Tilen
press the MODEbutton to accept the correct model.
:¢ A "beep" sounds \dlile t)ressing buttons for control programming.
One bee t) signals a change in the control dist)la }.Repeated beeps
mean the control will not accept a chang_ fl'om the button _ou
hme px_sse(t, and you should select another button.
:_ To prognu-n tile control, }_m will use the UP •, DOWN • and
MODEbuttons.
Use the MODEbutton to scroll arrow I_ to desired comrol function.
I.Press the MODEbutton until arrow
I_ points to PRESENTTIME.
Z Press tip • or DOWN • button
to set. The UP button adxances the time; the DOWN button moxes
the time in rexerse.
If file present time is bemeen noon and midnight, be sure PM shot_:s
in fl_e display. If the i)resent time is bet\_een midnight and noon, be
sure AM sl/o_:s in file (list)l_ft.
NOTE:Each t)x_ss of an UP • or DOWN • button changes the time
b_ one minum. Holding the button changes the time at a rapid rote.
3._l/en the px_sent time is correct, press MODEto accept.
SETWATERHARDNESSNUMBER I_ inS_]
I.Press tile MODEbutton until H_R_NaSS
arrow I_ [)Dints to HARDNESS.
Z Press LIP • or DOWN • button to
set xour, water hardness n umber in the displa}. DOWN decreases the
hardness xalue. UP increases the hardness xalue.
3.When the displa} sho_s your _,ter hardness (in groins t)er g_dlon),
press MODEto accept.
NOTE'If there is clear water iron in your water supply, you MI1need to
increase the hardness setting by 5 for each 1 ppm of clear water iron in
your water supply.
You can get the grains per gallon (gpg) har&_ess of your
water supply from a water analysis laboratory. If you are on
a mmficipal supply, call your local water deparmaent. Or call
Legend Technical Services, an independant laboratory, to request a
water hardness test kit at 1.800.826.8553, extension 47. If your report
shows harth_ess in parts per million (ppm) or nfiUigrams per liter
(rag/l), simply divide by 17.1 to get the equivalent number of grah_s
per gallon.
I_,_J _° -l'n nl /
SETRECHARGE(STARTING)TIME C'u u
I. Press the MODEbutton tmtil arrow II_
RECHARGE
points to RECHARGETIME. I _r_E
NOTE'Aflashing 2:00 AM (ti_ctory
defimlt) should sho_ in the dispb?. This is a good time tbr recharge to
start (takes about 2 hours) in most households berm_se _,ter is not in
tire. t_M4D "_ATER is bH)assed to house ti,ucets during rechaNe.
If no change is needed, go to step 3. To change the recharge starting
time, tbllo_ stop 2.
2.Press LIp • or DOWN • button to set the (lesi_d recharge start
time. Be sure to ob,_ene the AM or PM as _m did \_hen setting the
time of (b_.
NOTE'Eachpress of a button changes the time by 1 hour. Holding the
buttons in chano'es_,the time at a rai)id rate.
3.Press the MODEl)utton to accept.
SETSALTLEVEL n n 7_ SA_W,
I_l.U
I
I. Press the MODEbutton until
arrm_ _ points to SALTLEVEt.
2.Deten-nine lexel of salt in brine tank
using )ellow indicator on side of brine _ell, inside brine tank
(see illustration on t)age 5).
3.Press UP • or DOWN • button to I I I- [ _] SALTLEVEL
set tile SALTLEVELto correspond to -I.-I I
/
!
level on yellow indicator in brine tank. /
J
NOTE'Each press of a button changes the
level by increments of 0.5 up to 8.0. As the number increases, the salt
lexel bars increase on each whole numbe_: i,owerlng the salt lexel
below zero turns the SALTLEVELindicator OFF.
4.Press the MODEbutton to accept. The displa}
shows the present time of day and DAYSTO
EMPTY.RECHARGETONIGHTm_*yappear it
trait is new.
NOTE:Each press of a button changes tile display by l, between l and
_,._%_kbove-,,% the dis.l)lav,changes,....5 at a time (95,,,30, 35, etc.). Holding
a button in changes the mm-_bers at a rapid rate.