Manual

GEApp/iances,com
Service: Manually Initiated Electronics Diagnostics
!, To e_/ter diagnostics, press aN]d hold
the MOO/butt(m for 3 secm/ds m/ti]
tile I,ow Sah Harm scree_/ shows.
SALT
£_VEC
_+// 0 n
Z Press the MOOEbutto_/2 times to _ n O_
advm/ce throu_,h I,ow Sah Harm [_"_ O l
and Sah E{[h [e_l(} options. See n i-ir-i
Programming the Control for details U U U
am/ these two opthms.
3, OPERATIONOFDIAGNOSTICS
Motor Position
Valve l ., switch
p0s.t.0n... , /
-I-C
IZ_L
Water meter
- If there is role readim/g ira/the display, with _hucet
opera/, ched< the se_/sor. Pllll the sere/sot [_'om the
valve outlet port, amid pass a small magnet h/ f_'o_/t
of the sere/sot. Com/ter should im/dex ira/ the display.
If com/ter does m>t im/dex, check to make sure
harness is com/ected to board properly. If there is
a readim/g ira/the disp]a}, there may be a problem
associated wit]] tile tm'bim/e. Tm'_/ olt_water supp]},
dose the by-pass valve, and d!iscom/m/ect by-pass wdve
f_'om valve bad> C]/eck tm'b]m/e Iti>r bh/(]!im/g or
restricdol/ dlle to debris. If this does m/at correct
the proMem, the Time_; Sei/sol; or Tm'bim/e may
reqldre rep]acemeN/t.
4. Historical data abollt the soflem/er is available.
+ Press al/d hold the lip • buttol] to display the mlmber
of days this com/tro] has ]lad electrical power applied.
+ Press amid hold the DOWN • buttom/ to display the
mlmber of recharges im/itiated by this c<mtro] sim/ce the
mode] code m/limber was em/tered.
+ Valve Position - Press the RECHARGE @ button t(}
imlit[ate a recharge c) c]e. Press again/ t{>mamm]]y index
valve t(> m]ext pi>s[thm+ See Service: Manually Advance
Recharge Check for details.
0- Service
1 - Fill
2 - Brh/e
3 - Ba< kwash
4- Fast R[m/se
whei/ m)/t}t()]" s]]ou]d 1)e l'lH/m/ll/_,
* Position Switch Operation -
I-
L -- Closed -valve rotadm/g to _/ext pos[thm
n
U- ()pe_/ -3+l_!]'_le ill [){)siti(}]/, serx'ice, fill, bri_/e, etc+
+ Water Meter - h/dicates whether water is fJO_&li [/g
Position-_
switch
.Sensor
housing
Valve -_
outlet
pp0rt
andshaft
- (}00 i_/dicates _/{>water is flowi_/g through the valve
- ()pe_/ _/earby soR water fi_ucet
- 000 t(> 141 (c<mtimm]) shows water is Howi_/g. Display
repeats {i>r each ga]]{>_/ of water passi _/g th ro_lgh the
meter. Co_/tro] will beep at every gall<re.
5. Press the MOD_ bumm to remm to m>rma] operathm
a_/d display.
Service: Set Mode/(F or _) Code
E To chm/ge or check model code, _h'st press a_/d hold the
MODEbutto_l for 3 seco_/ds m/t[] the I,O_,_I Salt _]al'['ll
screei/ SHOWS.
Z Press a_/d ]mid tile MODE butt(m again/
f(}]" _} se(o[/ds. A dispIa} _Alith L_ Qd at
tile top _d11 appear.
3, Press the lit' • (>r DOWN • butte:Is
to se]ect the correct mode] code+
.... ,- Il
..... L 0 0
ll-ln
nq-i
o( • o( •
Ha.}-(,XSHa.}E o_ H45-(;NSH45E
4. Press the MODE butt<m cme time to term'+/ to +/orma]
opemthm a_/d disl>]ay+ It tile mode] code was cha_/ged:
+ the display w]]] go b];mk mome_/tar]]}, the_/ display the
mod!e] code e_/tered!.
+ the display will the_/ remm to the set prese_it time
display; a_/d the bhle i_/(]!icator light wi]] flash. The
control _d]] I/ave to be reprog_mm/ed. See Programming
the ControL
NOTE: ][ the colin'o] is ]eft [_/ am' of the above diagnostic
d[sp]a}s 01" a flas]/][/g d[s[}]a}' w]/e]ll setd_/g dine, hard,less,
etc., [t X_l]]]revert back to the _mrma] display [_/ 4 mhmtes.
/5