Manual

About the water softener system.
Breaking a Sail Bridge
Sometimes, a hard cn_st or sah bridge {orms im_
the sah storage area. It is I_slm]lv cal_sed bv high
h m_i ditv or th e w ton g ki m_d of sol t. Wh en th e
salt bridges, am_empty space forms between the
;_ater aN/(:[ salt. Thel/ salt will m/o) dissolve h/ the
water to make brim/e.
If the ]bHm_e tomsk ]s rid] of sail it is hard to tell
if you have a salt bridge. Salt is loose om_ top,
bm the bridge is raider it. The fo]]owim_g is the
best _av to check _kn" a salt bridge.
Salt sholdd be loose all the _a_ to the bottom
of the tam)k. Take a broom ham)die or like too],
am)d carehd]y imsh it do_l) ira)to the salt,
_orkim)g it i)[) aN)d do_m }If the to<)] strikes
a hard ob.ject (be sm'e it's m)ot the bottom or
sides of the taN)k), it's most likely a salt bridge.
Carehd]v break the brkJge wit]) the to()].
OO not [)ol) m)d o m)th e _a]]s of th e ta m)k.
If the wrom) g ki m)d of sol t made the bridge, take
it (mL The_) fill the tamH_wit]) m)gget or pellet
salt only. In )tumid areas, it ]s best to fill wit])
less salt, more oflem) to [(revei)t a salt bridge
_}'O FN) _k )1"1))i m)g,
Pencil
mark
Broom
handle
Push tool into salt
bridge to break
/
Water level
bridge
72
Cleaning the Nozzle and Venturi Assembly
A clean nozzle and ventnri is needed for the
water softening system to work- properly. This
sl]]a]] IH)it makes the silo[iota) to move brim)e
f_'om the salt storage area to the resin) ta_)k
dm'i _)g recharge_ If it becomes p]_)gged _ith
sa_)d, dirt, etc. the _ater s(]fle_)i_]g system
will m]t work a_)d v(m will get hard water.
To get to d) e nozz]e a_)d ve_)tin1, rein ore
the water soRe_)i_)g system top coven Be sm'e
the water soRe_)i_)g swtem is i_) se]wice cycle
(m] water pressm'e at nozzle a_)(:[ ve_m)r]).
The_L while ho]di_)g the _mzzle a_)d ventm']
h{>_)si_)g wit]] o_)e hand, remove the cap+ l,ifl
(]{)t the screen) s_q)port a_)d sc]'eelL the_) the
_)ozz]e a_)c[ vei)tm'i. Wash a_)(;[ ri_)se the parts h/
warm _ater m]t]l cleam ]{ _)eede& me a small
brash to remove ]ro_) or dirt. Also check m)d
clea_) the gasket.
NOTE:Some models have a small fio_ ph]g
located i_) the _)ozz]e a_](J ve_)tm'], a_)d/or
a small c(me shaped screen) h) the ]]ous]_)g.
Be sm'e t(} check a_id c]ea_) these parts,
if yore" m ode] ]s so eq _)il)ped.
Carehd]y rep]ace a]] parts i_] the correct order:
I,]ghdy h)bricate the o-ri_)g seal wit]] c]em)
silicone grease or petroleum .jelly and [)]ace h)
posi ti om [#stall and tighten Ne cap, by #and only.
Oo not overtighten the cap,
Cap
/
Nozzle & Venturi
housing
IMPORTANT:Be suresmall holesin the gasketare
centereddirectlyoverthe smallholesin the nozzleand
venturihousing.
*Install with numberedsideup,concaveside down.