Installation Guide

ManualsBrandsGE ManualsIndoor FixturesGE EP Series

Lighting Solutions

imagination at work

Lumination

LED Luminaires

(Series EP14 + Lutron TVI-LMF-2A Eco)

BEFORE YOU BEGIN

Read these instructions completely and carefully.

Save These Instructions

Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

Installation Guide

WARNING/AVERTISSEMENT

RISK OF ELECTRIC SHOCK

• Turn power off before inspection, installation or removal.

• Properly ground electrical enclosure.

RISK OF FIRE

• Follow all NEC and local codes.

• Use only UL or IEC approved wire for input/output connections.

Minimum size 18 AWG (0.75mm

RISQUES DE DÉCHARGES ÉLECTRIQUES

• Coupez l’alimentation avant d’inspecter, installer ou de retirer l’unité.

• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation

électrique.

RISQUES D’INCENDIE

• Respectez tous les codes NEC et codes locaux.

• N’utilisez que des ls approuvés par UL pour les entrées/sorties de connexion.

Taille minimum 18 AWG (0.75mm

Prepare Electrical Wiring

Electrical Requirements

• The LED driver must be supplied with 120-277 VAC, 50/60 Hz and connected to an individual properly

grounded branch circuit, protected by a 15 or 20 ampere circuit breaker. Use Min. 75°C supply conductor.

Grounding Instructions

• The grounding and bonding of the overall system shall be done in accordance with National Electric Code

(NEC) Article 600 and local codes.

Summary of content (6 pages)

PAGE 1
Installation Guide GE Lighting Solutions Lumination LED Luminaires TM (Series EP14 + Lutron TVI-LMF-2A Eco) BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT RISK OF ELECTRIC SHOCK • Turn power off before inspection, installation or removal. • Properly ground electrical enclosure. RISK OF FIRE • Follow all NEC and local codes. • Use only UL or IEC approved wire for input/output connections. Minimum size 18 AWG (0.75mm2).
PAGE 2
Electrical Connections Wiring Diagram White White Orange Black AC line Lutron Interface GND (Green-Yellow) Neutral (White) Line (Black) EcoSystem Link E1 EcoSystem Link E2 GND N Switched Hot/Out Constant Hot/In EcoSystem Digital Link Violet/White DALI DALI/0-10V 0-10V Violet Grey 0-10V Output – + Red Blue Red PSU Line Neutral Black White + – Black FIXTURE 1/4-20 screws 1 Carefully unpack unit from its packaging.
PAGE 3
E1 and E2 5 6 Connect AC line to black, white and green wires from Lutron interface with twist-on wire caps. Connect EcoSystem bus wires to the two purple Lutron connectors (Link E1 and E2). After completing connections, replace enclosure cover and screw down M4 screws and lock washers. Make sure screws are tight and cover is secured. Define Distance Between Canopy Sets Single unit installation scenario: Canopy set 1179mm (46.4 in.
PAGE 4
Unit Installation To driver enclosure Junction box in ceiling Crossbar 1 Carefully unpack unit from its packaging. Properly inspect for defects before installing. Wear work gloves to prevent dirt and oil from being transferred to the luminaire. 2 Attach crossbar to junction box in ceiling with two 1/4 inch screws. Repeat on other side.
PAGE 5
Optional Mounting Method - Connecting Suspended Fixtures in Series Canopy set without power cable Canopy sets with power cable 1 For multiple units installed in series, all canopy sets will have a power cable except the last canopy. Disconnect suspension wire Remove “Y” shape wires “Y” shape suspension wire Bracket 2nd luminaire 1st luminaire 2 On the 1st luminaire, disconnect the right-side suspension wire and “Y” shape suspension wire.
PAGE 6
Maximum Driver Remote Mounting Distance Supply Wire Gauge Wire Length* 18 AWG (0.82 mm ) 59.0 ft. (18 m) 16 AWG (1.31 mm ) 98.4 ft. (30 m) 14 AWG (2.08 mm2) 154.2 ft. (47 m) 12 AWG (3.31 mm2) 249.3 ft. (76 m) 2 2 * Includes fixture’s 6.6 ft. (2.0 m) power cord Specifications Input Voltage (VAC) 120 – 277V Input Power (W) 55W Input Frequency (Hz) 50/60 Hz Power Factor > 0.9 THD < 20% Control 0-10V & DALI Ceilings Cable Suspension System Warranty 5 years Dimensions 47.5 in. x 11.