INSTALLATION INSTRUCTIONS Advantium® Built-In Wall Oven CSB913 Español MFL59060928_00 31-2000354 Rev.0 03-19 GEA For a Spanish version of this manual, visit our Website at cafeappliances.com. Para consultar una version en español de este manual de instrucciones, visite nuestro sitio de internet cafeappliances.com.
Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT — Save these instructions for local inspector’s use. IMPORTANT — Observe all governing codes and ordinances. • Note to Installer — Be sure to leave these instructions with the Consumer. • Note to Consumer — Keep these instructions with your Owner’s Manual for future reference. • Skill Level — Installation of this appliance requires basic mechanical and electrical skills. • Completion Time — 1 Hour.
Design Information PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model. 29-3/4Ǝ 21-1/2Ǝ 2-1/4Ǝ 20 1/8Ǝ 1Ǝ 1-1/4Ǝ 13 1/4Ǝ TOOLS AND PARTS REQUIRED (NOT SUPPLIED) • • • • • • • • #2 Phillips screwdriver Hand-held drill High speed drill bit, 3/32Ǝ diameter 3/8Ǝ slot-head screwdriver Level Saw 3/8Ǝ min.
Installation Preparation ELECTRICAL REQUIREMENTS ELECTRICAL LOCATION Single Advantium Built-In Oven Installation: This product requires a 120-volt, 60 Hz, 15-amp circuit and draws 1.8 kilowatts. This product must be connected to a supply circuit of the proper voltage and frequency. 6” • Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating.
Standard Installation Preparation PREPARE THE OPENING PREPARE THE OPENING Advantium Built-In Oven can be installed in combination with other Built-In appliances. Always follow each product’s Installation Instructions to complete the installation. Installation over a Warming Drawer: 23-1/2” 30” Construct Single Advantium Built-In Oven Installation: Order a 30” wide single oven cabinet or cut the opening in a wall to the dimensions shown. 30” 25-1/4” 23-1/2” 17-1/2” solid bottom - Min.
Standard Installation Preparation PREPARE THE OPENING (CONT.) Installation over a Wall Oven: 30” 23-1/2” 25-1/4” 17-1/2” Construct solid bottom - Min. 3/8” plywood supported on all four sides. Must be able to support weight of oven and contents. PREPARE THE OPENING Installation over a Wall Oven and Warming Drawer: 30” 23-1/2” 25-1/4” 2” Min. (3” Recommended) 17-1/2” Per Oven Requirement 45-1/4” Min.
Standard Installation Preparation PREPARE THE OPENING (CONT.) Installation over another Advantium Built-In Oven: 30Ǝ 23-1/2Ǝ 25-1/4Ǝ 17-1/2Ǝ Construct solid bottom - Min. 3/8” plywood supported on all four sides. Must be able to support weight of oven and contents. 2 1/2Ǝ Min. (3 1/2Ǝ Recommended) PREPARE THE OPENING (CONT.) Installation under a Microwave Oven and over a Warming Drawer: 30Ǝ 23-1/2Ǝ 25-1/4Ǝ Per Microwave Oven Requirement Construct solid bottom - Min.
Standard Installation Preparation PREPARE THE OPENING 23-1/2Ǝ (CONT.) Installation beside another Advantium Built-In Oven: • If you are mounting an Advantium Built-In Oven beside another, use the dimensions shown. The middle rail separating the two openings may need to be larger than the 4-1/2Ǝ minimum shown. 25-1/4Ǝ 25-1/4Ǝ 17-1/2Ǝ 17-1/2Ǝ 4-1/2Ǝ Min. (5-1/2Ǝ Recommended) PREPARE THE OPENING (CONT.
Flush Mount Installation Preparation PREPARE THE INTERIOR PREPARE THE OPENING Cut and install side cleats: • Cut side wood cleats to height of cabinet opening and approx. 2-1/2” in depth. Install, on each side, 1-3/8” from the front face of the cabinet. Cut and install bottom cleat: • Cut bottom wood cleat to a height of 1-1/8”, a depth of the cabinet minus 1-3/8” and a width of 25-1/4” to fit between side cleats.
Flush Mount Installation Preparation 23-1/2” min. PREPARE THE OPENING The Advantium Built-In Oven can be installed beside another Advantium Built-In Oven in a side-by-side combination. G* Double Advantium Built-In Oven Installation: H* Cut the opening in a cabinet to the dimensions shown. 20 5/8” • Center divider acts as cleat for side of each respective unit. Only one additional side cleat needed per oven cutout.
Installation Preparation Preparation with an Accessory Storage Drawer As needed, see the Standard Mount Installation Preparation OR Flush Mount Installation Preparation for configuration details. Note the modified cutout height below. PREPARE THE OPENING (cont.) The Advantium Built-In Oven can be installed in combination with other GE Appliances/Monogram appliances. Always follow each product’s Installation Instructions to complete the installation.
Installation Instructions 1 REMOVE THE PACKAGING AND PARTS • Remove all packing material and tape. • Locate parts package containing mounting screws. • Remove the oven from the carton. Do not lift unit by handle or conduit. Two people are required to lift this oven. • Open the door and remove any packaging in oven.
Installation Instructions 2 SLIDE THE OVEN INTO THE CUTOUT CAUTION Two people are required to lift the oven into the opening. Grasp the bottom at front and rear. DO NOT USE THE HANDLE TO LIFT THE OVEN. DAMAGE WILL OCCUR. • Lift and hold the oven at the front of the opening. Hold the oven at an angle and plug in the power cord. 3 INSTALL BOTTOM TRIM NOTE: If installing the Advantium Built-In Oven with an accessory storage drawer, the bottom trim is not required. Proceed to Step 5.
Installation Instructions 4 INSTALL MOUNTING SCREWS • Slide the oven the remaining way into the opening so that the side flanges and control panel are against the cabinet frame. Make sure that the oven is centered in the opening. • Open the door, place a turntable tray in the oven and make sure that the tray in the unit is level. • Drill pilot holes through the side flanges. • Drive the color-matched screws into the side flanges. It is recommended that the screws be hand tightened.
Notes 31-2000354 Rev.
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. Printed in China 16 NOTE: Product improvement is a continuing endeavor at GE Appliances. Therefore, materials, appearance and specifications are subject to change without notice. 31-2000354 Rev.
