Installation Guide

ManualsBrandsGE ManualsIndoor FixturesGE BR Series

Lighting

Installation Guide

imagination at work

For Backlit Recessed Troffer Luminaires

Driver Replacement

BEFORE YOU BEGIN

Read these instructions completely and carefully.

WARNING/AVERTISSEMENT

RISK OF ELECTRIC SHOCK

• Turn power off before inspection, installation or removal.

• Properly ground electrical enclosure.

RISK OF FIRE

• Follow all NEC and local codes.

• Use only UL approved wire for input/output connections.

Minimum size 18 AWG (0.75mm

RISQUES DE DÉCHARGES ÉLECTRIQUES

• Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire.

• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.

RISQUES D’INCENDIE

• Respectez tous les codes NEC et codes locaux.

• N’utilisez que des ls approuvés par UL pour les entrées/sorties de

connexion. Taille minimum 18 AWG (0.75mm

Prepare Electrical Wiring

Electrical Requirements

• The LED driver must be supplied with 120-277 VAC or

347VAC, 50/60 Hz and connected to an individual properly

grounded branch circuit, protected by a 20 ampere circuit

breaker. Use min. 75°C supply conductor.

Grounding Instructions

• The grounding and bonding of the overall system shall

be done in accordance with National Electric Code (NEC)

Article 600 and local codes.

Components Supplied

• Driver of luminaire

Tools and Components Required

• T15 torx screwdriver

• UL listed conduit connections per NEC/CEC for nominal

conduit trades sizes ½” or ¾”

• UL recognized wire connectors

Save These Instructions

Use only in the manner intended by the manufacturer.

If you have any questions, contact the manufacturer.

Specications

Description Code Corresponding Luminaires

Backlit Troffer 22 and 14 driver (1-10V dimming) Backlit Troffer 22 and 14 Series

Backlit Troffer 24 driver (1-10V dimming) Backlit Troffer 24 Series

Summary of content (4 pages)

PAGE 1
Installation Guide GE Lighting Driver Replacement For Backlit Recessed Troffer Luminaires BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT RISK OF ELECTRIC SHOCK • Turn power off before inspection, installation or removal. • Properly ground electrical enclosure. RISK OF FIRE • Follow all NEC and local codes. • Use only UL approved wire for input/output connections. Minimum size 18 AWG (0.75mm2).
PAGE 2
Wiring Diagrams 1-10V Dimming: Standard Version VIOLET (1-10V) + GREY (1-10V) – Light Engine + – PSU RED + Line BLACK – Neutral WHITE BLUE Remote Switch 1-10V (Optional) (1-10V) – (1-10V) + GND N L 1-10V Dimming: 347V Version VIOLET (1-10V) + GREY (1-10V) – PSU Light Engine RED + BLUE – + – 347V TRANSFORMER Line BLACK Line BLACK BLUE Neutral WHITE Neutral RED BLACK Remote Switch 1-10V (Optional) (1-10V) (1-10V) + GND N L Lutron EcoSystem® Version Light Engine PSU Line BLACK Neu
PAGE 3
Driver Replacement Steps NOTE: The following steps depict the 22 Series luminaire. However, the procedure is the same for the 14 and 24 Series fixtures. 1 2 Rotate latches to unlock the front bezel. Backlit Troffer 22 and 24 3 Swing down panel and lift off front bezel. Backlit Troffer 14 For Backlit Troffer 22 and 24: unfasten the screw(s) holding the driver cover and remove it. For Backlit Troffer 14: unfasten the screws near the LED bar and remove the cover.
PAGE 4
Backlit Troffer 22 and 24 6 Reattach the driver cover with screw(s). 7 Hang panel on its hinges and swing up into place. Backlit Troffer 14 8 Rotate latches to lock the front bezel. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.