User Manual

14 49-5000444 Rev. 0
INSTALLATION INSTRUCTIONS
Installation Instructions
White-Westinghouse/Frigidaire/Carrier
52F Series (16” + 17-1/2” Deep)
4
4
3
8
3
8
1. Remove existing rear grille as shown on page 9 of
this manual and replace with provided louvered rear
panel.
NOTE: You may need to drill holes in flange of
existing sleeve to match new rear grille.
2. Attach (1) 1” x 3/8” x 25” long seal in the center at
the top of the sleeve. Remove the backing paper
and press into position.
3. Attach (2) 1” x 3/8” x 14” seals to the left and right
sides of the sleeve.
4. Attach (2) 1” x 3/4” x 14” long seals vertically 4.5”
from the left side of the sleeve and 4” from the
right side of the sleeve.
5. Center unit and gently slide unit into sleeve.
6. Before sliding all-the-way back, remove the
second screw from front on left side of unit.
7. Remove the plastic washer from the screw.
8. Screw and attach the other end of the ground
wire to the unit. Make sure that the toothed
washer is against the cabinet.
9. Slide the unit completely to the rear to ensure
a good seal, making sure the ground wire does
not become tangled.
10. If you have difficulty with mounting the grill to the
sleeve, follow the instructions for direct mounting
on page 15.
11. Seal and frame the unit as described on page 16.
White-Westinghouse or Frigidaire
(22” Deep)
1. Remove existing rear grille as shown on page 9 of this
manual and replace with provided louvered rear panel.
NOTE: You may need to drill holes in flange of existing
sleeve to match new rear grille.
Because of the increased unit depth, first try dry
fitting using the method described below:
2. Place (2) 1” x 1-1/2” x 14” seals against each side.
3. Gently slide unit in and check if amount extending from
the sleeve is sufficient once the trim frame is attached.
4. If position is correct, remove unit and proceed to the
next step. If not, go to step 8.
5. Attach (1) 1” x 1-1/2” x 15” long seal to the left side
and right side of the sleeve.
6. Cut (1) 1” x 1-1/2” x 25” seal to 14” long and attach
them vertically to the rear grill 4.5” from the left side of
the sleeve and 4” from the right side of the sleeve.
7. Attach (1) 1” x 1-1/2” x 25” long seal in the center at
the top of the sleeve. Remove the backing paper and
press into position. Proceed to step 14.
Use these next steps if the unit requires extra
extension into the room.
8. Attach 1” x 3/4” x 14” long seal over the solid vertical
portion of the rear grille.
9. Attach (4) 4-1/2” x 3-1/2” x 1-1/2” foam blocks with the
slot overlapping the seal above.
10. Install the divider into the slots of the foam blocks.
You may need to trim the length to size.
11. Repeat steps 8-10 for the other vertical shown
portion of the grille.
12. Attach (2) 1” x 1-1/2” x 14” seals along the sides of
the sleeve again making sure all seals are flush.
13. Cut the 1” x 1-1/2” x 25” seal to fit the top of the
sleeve. The pieces must be fitted flush to the edge of
the divider.
14. Center unit and gently slide unit into sleeve.
15. Before sliding all-the-way back, remove the first
screw from the front on left side of the unit.
16. Remove the plastic washer from the screw.
17. Screw and attach the other end of the ground wire
to the unit. Make sure that the toothed washer is
against the cabinet.
18. Slide the unit completely to the rear to ensure a good seal,
making sure the ground wire does not become tangled.
19. If you have difficulty with mounting the grill to the
sleeve, follow the instructions for direct mounting
on page 15.
20. Seal and frame the unit as described on page 16.
4
4
3
8
3
8