HO97916 USB 2.0 7-Port Hub INSTRUCTION MANUAL www.jascoproducts.
Table of Contents I. INTRODUCTION 3 II. OVERVIEW 4 III. SAFETY INSTRUCTIONS 5 IV. POWER MODE SETTING 6 V. HUB STAND ASSEMBLY 7 VI. HARDWARE INSTALLATION 13 VII. SOFTWARE INSTALLATION 15 VIII. TROUBLESHOOTING 16 IX. TECHNICAL SPECIFICATIONS 17 X. 18 FCC COMPLIANCE STATEMENT XI.
I. Introduction Please read this entire manual carefully before using your new USB 2.0 7-Port Hub and follow the instructions to prevent damage to the USB 2.0 7-Port Hub and/or the connecting devices. THIS PACKAGE INCLUDES: • • • • • • • USB 2.0 7-Port Hub USB 2.
II. Overview This USB 2.0 7-Port Hub allows you to connect up to seven USB devices to a single USB port on your computer, including up to five high-powered devices, simultaneously. This device complies with USB 2.0 specifications and supports data speeds up to 480 Mbps. It is compatible with all USB 1.1 and 2.0 devices. You can stack multiple hubs together to support up to 127 devices through a single USB port on your computer. FEATURES • • • • • • • USB 1.1 and 2.
III. Safety Instructions Always read the Safety Instructions carefully. Keep this user’s manual for future reference. Keep this equipment away from humidity. Lay this equipment on a reliable flat surface before setting it up. If any of the following situations arises, get the equipment checked by a service technician: • • • • • The equipment has been exposed to moisture. The equipment has been dropped and damaged. The equipment has obvious sign of breakage. The equipment is not working well.
IV. Power Mode Setting There are two power mode options for the USB 2.0 7-Port Hub. The first is self-power mode (recommended), which requires the use of the AC power adapter. In this mode, a maximum of five (5) high-powered USB devices may be connected to the hub at one time. If more than five high-powered devices are connected, you will notice a decrease in performance. (An additional hub is considered a high-powered device.
V. Hub Stand Assembly Options: • • • Stand may be mounted Magnetically or with Screws Hub may be oriented vertically or horizontally Hubs may be stacked Contents: Stand Magnets ¼” Screws Note: Package does not include the two screws needed to mount the hub to your desk. If you choose this mounting method, you will need to purchase the two screws separately.
A. Attach Hub Stand with Magnets Screw Magnet Metal Magnet Holder Screw Magnet Bottom of Stand Metal Magnet Holder 1. Place the metal magnet holder, and magnet on the stand as shown in the diagram. 2. Using the included screws, fasten the magnet to the stand as shown in the diagram. 3. Follow the directions in Sections C & D to attach the hub to the stand. 4. Attach the stand with the hub to your desk, or other flat metal location. Note: To eliminate data loss, do not place disks near the magnets.
B. Attach Hub Stand with Screws Screws Desk 1. You will need to purchase two screws separately. These are not provided. 2. Place the stand where you would like it secured to your desk. 3. Fasten the screws in the screw holes on both sides of the stand. 4. Attach the hub as described in Sections C & D. Note: You will need to purchase the two screws separately. These are not provided.
C. Attach Hub to Stand Vertically Hub Clips Push Hub Rails 1. Line up the tracks of either side of the hub with the rails on the stand. 2. Slide the hub all the way back on the stand until you hear a click.
D. Attach Hub to Stand Horizontally Hub Clips Push Hub 1. Line up the hooks on the bottom of the hub with the hub clips on the stand. 2. Slide the hub onto the stand until you hear a click.
E. Stacking Hubs Hub A Hub B 1. Face the Hubs in the same direction 2. Line up the hooks on the bottom of Hub A with the top cover of Hub B. 3. Slide Hub A onto Hub B as shown in the diagram.
VI. Hardware Installation 1. Make sure your computer has all the necessary updates required to support USB 2.0. These can be found on Microsoft’s website. 2. Position the Hub as desired using the directions in Section VI.
3. Plug the included AC power adapter into the Power Jack on the rear of the USB 2.0 7-Port hub. 4. Plug the AC power adapter into a standard electrical outlet or surge protector. The power LED should illuminate. (Note: Refer to Section IV for more details. It recommended that you use the power adapter initially. After you verify that all of the devices plugged into the hub are working, you may remove the ac power adapter. If any device ceases to function properly, you will need to use the ac power adapter.
VII. Software Installation Software installation is only required for Windows 98 and 98 SE users. Users of all other Operating Systems, including Windows NT, ME, 2000, XP and Mac, may skip this section. 1) When your hub is connected to your computer, Windows 98 and 98 SE will detect the hub and automatically run the “Add New Hardware Wizard”. 2) When the initial screen appears introducing the “Add New Hardware Wizard”, click Next.
VIII. Troubleshooting • Hub Not Seen Make sure you have installed all Windows updates and patches pertaining to USB. These are available on Microsoft’s website. • Hub Not Seen on a laptop USB 2.0 Hubs may not work on all laptops. Try the hub on a desktop computer to confirm functionality of the hub. If this works, contact your computer dealer.
IX. Technical Specifications USB Hub: Standards: Operating Systems: Data Speed: Upstream Ports: Downstream Ports: LEDs: Power: 7 Ports USB 1.1 and 2.0 Compatible Windows 98 SE, ME, 2000, XP or later Mac OS 9.X and above High: 480 Mbps Full: 12 Mbps Low: 1.5 Mbps Series A plug x 1 Series A receptacle port x 7 1 Power Indicator, 7 Port Activity Indicators Self-Power (AC Adapter): 5 Volts, 2.
X. FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed or used in accordance with the instructions, may cause harmful interference to radio communications.
XI. Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied.
