Instructions / Assembly

: 250x175mm
When using electric products basic precautions should always be followed inchuding the following:
a)
a ) When the product is placed on a live tree. the tree should be well maintained and fresh. Do not place on live trees
in which the needles are brown or break off easily. Keep the tree holder filled with water.
b ) If the product is placed on a tree, the tree should be well secured and stable.
c ) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire
insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
d ) When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or
bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
e ) When not in use, store neatly in a cool, dry location protected from sunlight.
b ) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are
used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is
not provided, contact a qualified electrician for proper installation.
c ) This seasonal use product is not intended for permanent installation or use.
d ) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
e ) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
f ) Do not let lamps rest on the supply cord or on any wire.
g ) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
h ) This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not
be played with or placed where small children can reach it.
i ) Do not use this product for other than its intended use.
j ) Do not hang ornaments or other objects from cord, wire, or light string.
k ) Do not place lighting string on carpeting, drapes, furniture, or allow it to contact vinyl siding while the power is on.
l ) Do not perform any maintenance or troubleshoot for bad or broken lamps while the power is on.
m) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
n ) Do not cover the product with cloth, paper or any material not part of the product when in use.
o ) This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric
shock. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician. Do not use with an extension cord unless plug can be fully
inserted. Do not alfer or replace the plug.
p ) This product is equipped with push-in type lamps. Do not twist lamps.
q ) This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation.
If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be
attached to the product. Replace the fuse as per the suer servicing instructions (follow product marking for proper
fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product
should be discarded.
r ) Read and follow all instructions that are on the product or provided with the product.
s)
When using electric products basic precautions should always be followed inchuding the following:
a
)
a
) When the product is placed on a live tree. the tree should be well maintained and fresh. Do not place on live trees
in
which the needles are brown or break off easily. Keep the tree holder filled with water.
b
) If the product is placed on a tree, the tree should be well secured and stable.
c
) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire
insulation
or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
d
) When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or
bushes,
to avoid any undue strain or stress on the product conductors, connections, and wires.
e
) When not in use, store neatly in a cool, dry location protected from sunlight.
b
) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are
used
in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is
not
provided, contact a qualified electrician for proper installation.
c
) This seasonal use product is not intended for permanent installation or use.
d
) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
e
) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
f
) Do
not let lamps rest on the supply cord or on any wire.
g
)
Unplug
the product when leaving the house, when retiring for the night, or if left unattended.
h
) This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not
be
played with or placed where small children can reach it.
i
) Do not use this product for other than its intended use.
j
) Do
not hang ornaments or other objects from cord, wire, or light string.
k
) Do not place lighting string on carpeting, drapes, furniture, or allow it to contact vinyl siding while the power is on.
l
) Do not perform any maintenance or troubleshoot for bad or broken lamps while the power is on.
m)
Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
n
) Do not cover the product with cloth, paper or any material not part of the product when in use.
o
) This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric
shock. This
plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
If
it still does not fit, contact a qualified electrician. Do not use with an extension cord unless plug can be fully
inserted.
Do not alfer or replace the plug.
p
) This product is equipped with push-in type lamps. Do not twist lamps.
q
) This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation.
If
the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be
attached
to the product. Replace the fuse as per the suer servicing instructions (follow product marking for proper
fuse
rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product
should
be discarded.
r
) Read and follow all instructions that are on the product or provided with the product.
s
)
Model No . NLS-150/3FN(0.51)Model No . NLS-150/3FN(0.51)
150 lights 6'X4' commercial grade net style lights150 lights 6'X4' commercial grade net style lights
Fuse replacement:
Bulb replacement:
Most often, fuses blow because too many sets have been strung end-to-end.
a ) Before changing fuses, make sure the set is unplugged.
b ) Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
c ) Using a flathead screwdriver, open fuse cover. Slide open
the fuse access cover on top of attachment plug towards blades.
d ) Remove fuses carefully.
e ) Risk of fire. Replace fuse only with 5 Amp,125 Volt fuse (provided with product).
f ) Close fuse cover. Slide closed the fuse access cover on top of attchment plug.
Make sure door is fully closed and fuses are completely covered.
g ) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse)
that should not be removed. Discard product if the attachment plug is damaged.
Before changing bulbs, make sure set is unplugged.
Step 1: Grasp plug and remove from the Step 3: Replace bulb with only 2.5 Volt, 0.425 Watt
receptacle or other outlet device. super brightness midget push-in type
Do not unplug by pulling cord. lamp provided with product. Push spare
Step 2: Hold bulb by the plastic base bulb/base assembly into socket. Do not
and pull bulb/base straight twist bulb when inserting into socket.
out of socket. If bulbs are twisted, part of the set will not light.
If the spare bulbs provided with the product have no plastic base or
the plastic base does not fit, first follow steps 1 - 2 above. Then
a ) Remove the old bulb by strainghtening the bulb wires and
pulling bulb straight from the base.
b ) Replace the new bulb by straightening the bulb leads and
aiming each wire into a separate hole in the plastic base.
c ) Make sure each bulb lead comes out an exit opening at the bottom of the plastic base.
Now bend each lead up such that each bulb lead fits closely agains the narrow side of the plastic base.
1. This lighting string is rated 61.2 Watts (0.51 Amps),do not overload. Connect other lighting
strings or decorative outfits end-to-end up to a maximum of 432 Watts (3.6 Amps) total.
If connecting to a lighting string that does not have a Wattage (W) rating {found on the tag within 6 inches of the
plug} calculate the wattage as follows: Multiply the current ( A)which is on the flag-type tag by 120.
For example: Lighting string is rated 120 V,60 Hz,0.51 Amps. 0.51 X 120 = 61.2 Watts
Add the wattage of each light string together for a total of 432 Watts or less. (Do not exceed 432 Watts.)
2. To reduce the risk of overheating, replace burned-out lamps promptly. Use 2.5 Volt, 0.425 Watt lamps only.
3. To reduce the risk of fire and electric shock: a) Do not install on trees having needles, leaves or branch
coverings of metal or materials which look like metal, and b) Do not mount or support strings in a manner that
can cut or damage wire insulation.
Fuse replacement:
Bulb
replacement:
Most often, fuses blow because too many sets have been strung end-to-end.
a
) Before changing fuses, make sure the set is unplugged.
b
) Grasp plug and remove from the receptacle or other outlet device.
Do
not unplug by pulling on cord.
c
) Using a flathead screwdriver, open fuse cover. Slide open
the
fuse access cover on top of attachment plug towards blades.
d
) Remove fuses carefully.
e
) Risk of fire. Replace fuse only with 5 Amp,125 Volt fuse (provided with product).
f
) Close fuse cover. Slide closed the fuse access cover on top of attchment plug.
Make
sure door is fully closed and fuses are completely covered.
g
) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse)
that
should not be removed. Discard product if the attachment plug is damaged.
Before
changing bulbs, make sure set is unplugged.
Step
1: Grasp plug and remove from the Step 3: Replace bulb with only 2.5 Volt, 0.425 Watt
receptacle
or other outlet device. super brightness midget push-in type
Do
not unplug by pulling cord. lamp provided with product. Push spare
Step
2: Hold bulb by the plastic base bulb/base assembly into socket. Do not
and
pull bulb/base straight twist bulb when inserting into socket.
out
of socket. If bulbs are twisted, part of the set will not light.
If
the spare bulbs provided with the product have no plastic base or
the
plastic base does not fit, first follow steps 1 - 2 above. Then
a
) Remove the old bulb by strainghtening the bulb wires and
pulling
bulb straight from the base.
b
) Replace the new bulb by straightening the bulb leads and
aiming
each wire into a separate hole in the plastic base.
c
) Make sure each bulb lead comes out an exit opening at the bottom of the plastic base.
Now
bend each lead up such that each bulb lead fits closely agains the narrow side of the plastic base.
1. This
lighting string is rated 61.2 Watts (0.51 Amps),do not overload. Connect other lighting
strings
or decorative outfits end-to-end up to a maximum of 432 Watts (3.6 Amps) total.
If connecting
to a lighting string that does not have a Wattage (W) rating {found on the tag within 6 inches of the
plug}
calculate the wattage as follows: Multiply the current ( A)which is on the flag-type tag by 120.
For
example: Lighting string is rated 120 V,60 Hz,0.51 Amps. 0.51 X 120 = 61.2 Watts
Add
the wattage of each light string together for a total of 432 Watts or less. (Do not exceed 432 Watts.)
2. To
reduce the risk of overheating, replace burned-out lamps promptly. Use 2.5 Volt, 0.425 Watt lamps only.
3. To
reduce the risk of fire and electric shock: a) Do not install on trees having needles, leaves or branch
coverings
of metal or materials which look like metal, and b) Do not mount or support strings in a manner that
can
cut or damage wire insulation.
For questions and/or assistance, call customer service at 1-877-398-7337
or visit us on the web at www.geholidaylighting.com.
2014 Nicolas Holiday Inc., 9F., No.37, Guangfu N Rd., Taipei, Taiwan 10560
PRINTED IN CHINA
All rights reserved.
For questions and/or assistance, call customer service at 1-877-398-7337
or
visit us on the web at www.geholidaylighting.com.
2014
Nicolas Holiday Inc., 9F., No.37, Guangfu N Rd., Taipei, Taiwan 10560 All rights reserved.
PRINTED
IN CHINA
C
CAUTION:
LAMP
SHUNT
SOCKET
LAMP
BASE
LAMP
WIRES
A
B
C
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONSREAD AND FOLLOW ALL SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
USE AND CARE INSTRUCTIONS
SAVE THESE INSTRUCTIONS
USE AND
CARE INSTRUCTIONS
USER SERVICING INSTRUCTIONSUSER SERVICING INSTRUCTIONS