24950 Universal Remote Instruction Manual ON-OFF SETUP TV VCR CH VOL VOL CH SLEEP INPUT PREV.
Table of Contents Introduction Introduction ...................................................... 3 Button Functions ............................................... 4 Setup ............................................................... 6 Battery Installation ....................................... 6 Battery Saver ............................................... 7 Code Saver ................................................. 7 Power-On default ........................................ 7 Code Setup .........
Button Functions, cont. Button Functions 1. 24. 2. VCR 3. 23. TV 22. 4. 21. 5. 20. 6. 19. 7. 18. INFO GUIDE 8. 17. 9. 16. L 10. 15. 11. 14. 12. 13. Note: The Record button must be pressed TWICE to record from your VCR. For some brands of VCRs, you might need to press the Record button once, then press it again for three seconds. Some buttons on the remote might have functions that are referred to by different names on the device you are controlling. E.G. PREV.
Setup Setup, cont. Battery Installation Battery Saver 1. On the back of the remote, push down on the tab and lift the cover off. 2. Match the batteries to the + and - marks inside the battery case, then insert 2 AAA alkaline batteries. 3. Press the battery cover back into place. Your remote automatically turns off if the buttons are depressed more than 30 seconds. This will save your batteries should your remote get stuck in a place where the buttons remain depressed (e.g., between the sofa cushions).
Code Search, cont. Direct Code Entry 1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button. 2. Press and release the desired mode button (TV, VCR, etc.). The red indicator blinks, then stays lit. 3. Enter the 4 digit code from the code tables (on separate sheet). Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes. 4. With your device on, press CHANNEL UP.
Setup, cont. Setup, cont. Programming Combo Device Codes Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/ VCR, etc.) will require you to set up two different Mode buttons to control both parts of the Combo device. For example, if you have a TV/DVD Combo, you might need to set up one code under the TV button to control the TV part AND a separate code (under any other Mode button) to control the DVD part. Controlling Devices Requiring Separate Power On and Off Buttons, cont.
Setup, cont. Sleep Timer Any Mode chosen for Volume/Mute control MUST have its own Volume/Mute function or the Volume/Mute buttons will do nothing. Setting ALL Volume/Mute Control to any one Mode This routine can set all Modes to “punch-through” to any one chosen Mode for Volume/Mute button control without the needing to change to that Mode. 1. Press and hold the SETUP button until the red indicator turns on, then release the button. 2.
Code Learning Tips On Learning, cont. The learning feature lets you “learn” functions from your original remote control. For example - you may want to use your remote to operate the RANDOM PLAY feature from your original CD remote control. This remote is equipped with an “easy learning” feature that lets you “learn” features (such as RANDOM PLAY from your original CD remote). Tips On Learning You can only learn one device type under any one Mode button e.g.
Learning Commands, cont. IR Transmitter Finder Feature 1. Point both remotes facing each other by approximately 1 inch apart (see Tips on Learning on previous pages). 2. Press and hold the SETUP button until the red indicator turns on, then release the button. 3. Press and release the desired Mode button (TV, VCR, etc.), the red indicator blinks then stays on. 4. Press and release the LEARN button, the red indicator blinks then stays on. 5.
Troubleshooting Clearing Commands To Clear all Learned Commands under a mode Remote does not operate your product. Clearing learned commands is helpful if, for example, you replace your CD player with another brand or model. If you had learned a feature from your old CD player’s original remote on to this remote (such as RANDOM PLAY), that feature would no longer work for your new CD player. Should you wish to remove or clear one or more “learned” commands, follow the steps below: • 1.
24950 Universal Remote Instruction Manual Jasco Products Company 311 N.W.
