RM24945 Set Universal Remote Instruction Manual K24945 Locator Keyfob R24945 Remote
Table of Contents Introduction ........................................................... 3 Setup .................................................................... 3 Battery Installation ........................................... 3 Battery Saver ................................................... 3 Code Saver ...................................................... 3 Code Setup ...................................................... 3 Button Functions .............................................
Button Functions, cont. Button Functions Some buttons on the remote might have functions that are referred to by different names on the device you are controlling. E.G. PREV.CH may be called RECALL, or CLEAR may be called EXIT. These differences depend on the brand and model of your product. Also, this remote can only operate features that exist on your product. E.G., your product must have previous channel ability for the PREV.CH button to operate this feature.
Audio Button Descriptions Press the AUDIO device button to enable the AUDIO MODE. Audio functions are indicated by the blue button descriptions. LEVEL+/LEVEL- Sets the level of the speakers during test tone mode. DSP ON•OFF Enables the receiver’s Digital Sound Processing mode. DSP MODE When the DSP mode is enabled, pressing this button lets you toggle through the various DSP modes. CD, TAPE, TUNER, TV, VIDEO Used to directly select the device you want to control. (Works in AUDIO mode).
Surround Sound Feature The surround sound feature may be turned ON/OFF by pressing the SURR ON•OFF button. 1. Press the SURR MODE button until the desired mode is found. 2. Press DELAY+ or DELAY- to achieve the desired delay affect. 3. Press the DSP ON•OFF button to turn DSP (Digital Sound Processor) ON or OFF. 4. Press the DSP mode button until the desired effect is achieved. 5. Press the TEST button to listen to speaker levels. 6. Press FRONT, CENTER, or REAR buttons to select speakers.
Code Search Using Your Remote If your device does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following these steps. 1. Manually turn on the device (TV, VCR, etc.) to be controlled. 2. Press and hold the CODE SEARCH button until the red indicator stays on, then release the CODE SEARCH button. 3. Press and quickly release the desired device button (TV, VCR, etc.). The red indicator blinks off once. 4.
Using Your Remote, cont. Sleep Function Using Your Remote, cont. Controlling Devices with Separate Power On and Off Buttons The Sleep button enables the remote to turn off your TV after a period of 1 to 99 minutes as shown below. The remote must be in TV mode to set a Sleep Timer. This feature works even if your TV does not have a sleep feature.
Using Your Remote, cont. Using Your Remote, cont. Volume/Mute Control and PunchThrough Setting any Mode to use its own Volume/Mute Control This remote lets you select which device Mode controls your Volume/Mute buttons. The remote is initially set for all device Modes to use their own Volume/Mute control if present. If the programmed code has no Volume/Mute operation of its own then those buttons will punch-through control to the TV Mode device without needing to change to TV Mode.
Using the FIND IT Locator Functions You can use the FIND IT remote to find the Keyfob, whether it has keys attached, or if it’s attached to something else. Or you can use the Keyfob to find your misplaced Remote. The Keyfob and the Remote are a “set” and need to be programmed to find each other. Here are the simple steps. 1. Insert the Batteries in the Remote Insert 2 AAA alkaline batteries in the battery compartment on the back of the Remote. Observe the + and – notations.
FIND IT Locator Functions, cont. 3. Set the ITEM # for the Keyfob a. Remove the plastic tab from the battery compartment. The Keyfob beeps and immediately goes into setup mode. The LED blinks continuously to indicate that the Keyfob is ready to be set up. To enter the setup mode at any other time, press and hold the 1 and 3 buttons simultaneously for about 3 seconds. A warble beep is emitted and the LED flashes continuously. To Replace the Battery: • • • Open the battery compartment on the back.
FIND IT Locator Functions, cont. Troubleshooting Using a FIND IT Keyfob to find a misplaced FIND IT Remote If the Remote does not operate your device, TV, VCR, Cable Box, etc. To find a misplaced FIND IT Remote, simply press the button on one of your FIND IT Keyfobs corresponding to the item # you set your FIND IT Remote to (1 thru 6). If the Remote is in range, it will begin to flash its LED and beep. • The maximum distance the lost Remote can be from the Keyfob is about 30 ft.
90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied.
RM24945 Set Universal Remote Instruction Manual Jasco Products Company 311 N.W.
