24116 Universal Remote Instruction Manual
Table of Contents Introduction................................................................... 3 Button Functions........................................................ 4 Initial Setup.................................................................... 6 Battery Installation.............................................. 6 Battery Saver.......................................................... 6 Code Saver.............................................................. 6 Power-On default.........
Introduction Congratulations on your purchase of the 24116 Universal Remote Control. It is one of the most unique looking, and easy to use remote controls available today. With the 24116 Universal Remote, juggling multiple remote controls is a thing of the past. Your 24116 Universal Remote controls up to 4 devices, including the most popular brands of TV, DVR, DVD, SAT, CBL, and audio equipment. Note: Some functions from your original remote may not be controlled by the 24116 Universal Remote.
Button Functions 1. 20. 2. 19. 3. 18. 4. 17. 5. 16. 6. 15. 7. 14. 8. 13. 9. 12. 10. 11. Note: The Record button must be pressed TWICE to record. For some brands of VCRs, you might need to press the Record button once, then press it again for three seconds. Some buttons on the remote might have functions that are referred to by different names on the device you are controlling. E.g., LAST may be called RECALL, or ENTER may be called DISPLAY.
Button Functions, cont. 1. ON-OFF: Turns device On or Off. 2. Red Indicator: Lights when any button is pressed. 3. TV, DVD, CBL/SAT, DVR/AUX: Selects product to be operated. 4. MUTE: Turns off the TV sound while the picture remains. 5. VOLUME UP/DOWN: Changes the volume level of the product, normally the TV. 6. UP, DOWN, LEFT & RIGHT: Navigation buttons. 7. MENU: brings up the DVD disc Menu screen. Use with the UP, DOWN, LEFT & RIGHT navigation buttons. 8.
Initial Setup Battery Installation 1. On the back of the remote, push down on the tab and lift the cover off. 2. Match the batteries to the + and - marks inside the battery case, then insert 2 AAA alkaline batteries. 3. Press the battery cover back into place. Battery Saver Your remote automatically turns off if the buttons are depressed more than 30 seconds. This will save your batteries should your remote get stuck in a place where the buttons remain depressed (e.g., between the sofa cushions).
Direct Code Entry 1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button. 2. Press and release the desired mode button (TV, DVD, etc.). The red indicator blinks, then stays lit. 3. Enter the 4-digit code from the code tables (on separate sheet). Note: After a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes. 4. With your device on, press CHAN UP. If the device responds, no further programming is required.
Code Search If your product does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following these steps. 1. Manually turn on the device (TV, DVD, etc.) to be controlled. 2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button. 3. Press and quickly release the desired mode button (TV, DVD, etc.). The red indicator blinks off once. 4.
Code Identification Feature The Code Identification Feature allows you to identify the four digit library code stored under your device key. For example, if you want to find out what 4-digit code is stored under your TV device key, follow the six steps below: 1. Press and hold the SETUP button until the red indicator stays on. Release the SETUP button. 2. Press and release the desired mode button (TV, DVD, etc.). The red indicator blinks, then stays lit. 3. Press and release the SETUP button.
Setup Programming Combo Device Codes Some Combo devices (e.g., TV/VCR, TV/DVD, DVD/ DVR, etc.) will require you to set up two different Mode buttons to control both parts of the Combo device. For example, if you have a TV/DVD Combo, you might need to set up one code under the TV button to control the TV part AND a separate code (under any other Mode button) to control the DVD part. Controlling Combo Devices Some Combo devices (e.g., TV/VCR, TV/DVD, DVD/ DVR, etc.
Setup, cont. Controlling Devices Requiring Separate Power On and Off Buttons, cont. To turn the TV off, press and release the ON-OFF button to transmit the Power Off button command. This method can be applied similarly to any device and is available for all Modes. Note this feature is not supported by all codes. DVD/DVR Punch-Through Feature This remote allows the 6 DVR transport buttons (i.e.
Setup, cont. Any Mode chosen for Volume/Mute control MUST have its own Volume/Mute function or the Volume/ Mute buttons will do nothing. Setting ALL Volume/Mute Control to any one Mode This routine can set all Modes to “punch-through” to any one chosen Mode for Volume/Mute button control without the needing to change to that Mode. 1. Press and hold the SETUP button until the red indicator turns on, then release the button. 2.
Troubleshooting Remote does not operate your product. • Press the mode button of the product you want to control. • Program the remote with a new code. • Install new batteries. (You might have to reprogram your remote after installing new batteries.) • Remote may not be compatible with your product. Remote does not operate some features of your product. • Program remote with a new code.
90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied.
Jasco Products Company 10 E.
