User Manual 1.32 m (52 in.) Savanna III LED Ceiling Fan MODEL: 21243 ITM./ART.1162881 120V 60Hz, MADE IN CHINA Customer Assistance 1-866-885-4649 Contact a qualified electrician or call the Customer Care Service Team at 1-866-885-4649 Customer Service hours of operation are 9:00AM-5:00PM EST -Monday-Friday Note: Installation videos for GE fans with SkyPlug technology can be viewed and downloaded on www.gelightingandfans.
Safety Rules READ AND SAVE THESE INSTRUCTIONS 1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code. Electrical installation should be performed by a qualified licensed electrician. 3. WARNING: to reduce the risk of electrical shock or fire, do not use this fan with any solid-state fan speed control device.
SAFETY TIPS 1. Before working on a circuit , go to the main service panel and remove the fuse or turn off the breaker that controls that circuit . Downrod 2. Tape a sign to the panel warning others to leave the circuit alone while you work. 3. Before touching any wire, use a voltage tester to make sure it’s not live. 4. Whenever you check for voltage in a receptacle, check both outlets; each may be controlled by a separate wiring circuit . 5. When replacing fuses, turn off the main power first .
Tools Needed (Not Supplied) Required Flathead Screwdriver (1# screwhead recommended) Step Ladder Philips Screwdriver Wire Stripper Safety Glasses Soft Cloth 3
Hardware Included Carefully unpack and identify each part to make sure you have everything ready for installation. Lay out each part on a clean area such as a table or floor.
Package Contents Carefully unpack and identify each part to make sure you have everything ready for installation. Lay out each part on a clean area such as a table or floor.
Fan Installation Drawing Review important safety instructions before installation.
SkyReceptacle Typical Wire Configurations TYPICAL WIRE CONFIGURATIONS: Black(Live) White WIRING DIAGRAM #1: Typical Wiring Configuration for 1 Wall Switch Green Black(Live 1) WIRING DIAGRAM #2: Typical Wiring Configuration for 2 Wall Switches White Green Red(Live 2) Black(Live) Wire Nut WIRING DIAGRAM #3: Wiring Configuration with more than 1 of the same colored wires in the outlet box White White Green NOTE: If you do not have standard wiring configurations and have questions about the wiring in your o
SkyReceptacle Installation 0-1.5mm Gap 0-1.5mm 4mm rubber washer 1.5-3mm Gap 1.5-3mm 7mm rubber washer >3mm Gap 4mm rubber washer 7mm rubber washer 8 >3mm Important: Install SkyReceptacle with rubber washers to avoid a gap or uneven surface, and to ensure proper placement of receptacle on the ceiling.
SkyReceptacle Installation 1 1/2"/12.7mm OK Not OK Not OK 2 Outlet Box (not Supplied) Terminal’s Bottom view on Sky Receptacle Sky Receptacle Insert wires into terminal, tighten screw to secure wires.
SkyReceptacle Installation 3 Rubber Washer ( Install cover plate if supplied ) not provided on all models Using the rubber washer when installing receptacle ensures proper placement of the receptacle on the ceiling 10
Fan Installation 4 Slide down trim ring from canopy. 5 Remove rubber inserts from canopy and discard.
Fan Installation Receptacles Slots 6 Bracket with Push Lever Receptacles Slots Initial "+" formation while lifting fan and inserting plug into receptacle Press up on the push lever while lifting the fan. For correct alignment , make sure the bracket with plug and push lever is placed between the receptacle bracket metal slots ( in a "+ " formation ) as shown. Insert the plug into the receptacle, keeping the lever pushed up while turning fan to the right .
Fan Installation 7 Once installed, tighten all 4 screws. 8 Reinstall trim ring, being careful not to depress the push lever. 9 Adjust fan housing so ball is properly seated in bracket .
Fan Installation 10 Install fan blades. 11 Install LED light kit. Install light kit pan. 12 Install shade-turn to secure.
Fan Operation Reverse Switch Summer Winter 15
5HPRWH &RQWURO 5(027( )81&7,216 2SHUDWLRQ LQGLFDWRU 0HGLXP VSHHG 7KLV EXWWRQ WXUQV WKH IDQ 21 RU 2)) /RZ VSHHG +LJK VSHHG EXWWRQ 7KLV EXWWRQ FRQWUROV WKH OLJKW DQG DOVR FRQWUROV WKH EULJKWQHVV VHWWLQJ 3UHVV DQG UHOHDVH WKH EXWWRQ WR WXUQ WKH OLJKW 21 RU 2)) 3UHVV DQG KROG WKH EXWWRQ WR VHW WKH GHVLUHG EULJKWQHVV WKH OLJKW ZLOO VORZO\ LOOXPLQDWH WR PD[LPXP OLJKW RXWSXW DQG WKHQ VWRS ZKHQ KROGLQJ WKH EXWWRQ WKHQ UHOHDVH WKH EXWWRQ DQG KROG LW DJDLQ XQWLO LW UHDFKHV PLQLPDO LOOXPLQDWLRQ
5HPRWH &RQWURO 5(027( &21752/ 23(5$7,216 2SHUDWH )DQ XVLQJ 7UDQVPLWWHU &RGH 3UH 6HW E\ )DFWRU\ 6WHS 5HVWRUH SRZHU WR FHLOLQJ IDQ 6WHS ,QVWDOO WZR YROW $$$ EDWWHULHV, SURYLGHG.
Remote Control Pairing Instructions REMOTE CONTROL PAIRING INSTRUCTIONS: Important Note : By default , every fan has been pre-programmed at the factory and should be fully functional once installation is completed. There is no need to perform the pairing process. Make sure all wiring connections have been properly made and are secure. Make sure batteries are installed correctly in the transmitter. Make sure batteries have a full charge or replace with new batteries.
Blade Wobble Balancing B A Not OK C X Y X - Y< 3mm / ⅛in. X - Y >3mm / ⅛in.
Maintenance PRODUCT MAINTENANCE * Suggestions to help you maintain your fan * Because of the fan’s natural movement , some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling). * Cleaning the fan * Clean your fan periodically to help maintain its new appearance over the years. Use only a soft brush or lint-free cloth to avoid scratching the finish.
Troubleshooting CAUTION: Switch off power supply before carrying out any of these checks. 1. Fan will not start: -Check main and branch circuit fuses or breakers. -Check to make sure the wall switch is in the on position. -Check remote control operation. 2.Fan will not operate: - The SkyPlug on the fan canopy should be fully inserted into the receptacle. There are 2 levels of ball bearings on the plug stem. The lower set of ball bearing needs to be fully inserted into the SkyReceptacle.
