User Manual Treviso LED Ceiling Fan 52 in. (1.
Safety rules 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the latest edition of National Electrical Code “ANSI/NFPA 70” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. WARNING: To reduce the risk of electrical shock or fire, do not use this fan with any solid-state fan speed control device.
Basic guidelines for working with electricity 1. Before working on a circuit, go to the main service panel and remove the fuse or trip the breaker that controls that circuit. 2. Tape a sign to the panel warning others to leave the circuit alone while you work 3. Before touching any wire, use a voltage tester to make sure it’s not live. 4. Whenever you check for voltage in a receptacle, check both outlets-each may be controlled by a separate wiring circuit. 5.
To begin / tools needed (not supplied) REQUIRED Flathead Screwdriver Phillips Screwdriver Safety Glasses Pliers Wire Cutters Electrical Tape Step Ladder Wire Strippers Soft Cloth 4
Hardware included ATTENTION: parts are not to scale. Carefully unpack and identify each part to make sure you have everything ready for installation. Lay out each part on a clean flat area such as a table or floor.
Package contents ATTENTION: parts are not to scale. Carefully unpack and identify each part to make sure you have everything ready for installation. Lay out each part on a clean flat area such as a table or floor.
Fan installation drawing WARNING: review important safety instructions before installation Outlet Box (Not Provided) Star Washer Wood Screw (Long) Mounting Bracket Black Wire Receiver Flat Washer Spring Washer Mounting Screw Ground Wire from Mounting Bracket Plastic Wire Nut Neutral White Wire White Wire Blue Wire Black Wire Fan Motor Assembly Ground Wire from the Fan Motor Assembly Mounting Bracket Screw Blade Fibre Washer Mounting Plate Blade Screw Mounting Plate Screw LED Light Kit Light Kit Mou
Fan installation INSTALLING THE MOUNTING BRACKET Q C A E C A 1. Use metal outlet box (sold separately) suitable for fan support. Secure outlet box directly to the building structure using wood screws (A) and star washers (C). Outlet box must support 15.9 kg (35 lb.) min. D B 2. Install mounting bracket (Q) to the outlet box in ceiling using the mounting screws provided with the outlet box (two additional mounting screws (B), spring washers (D) and flat washers (E) are provided in the hardware bag).
Fan installation PREPARING THE ELECTRICAL CONNECTIONS WARNING: to avoid possible electric shock, be sure electricity is turned off at the main fuse box before wiring. If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Follow the steps below to prepare the electrical connections. After that, conform with the descriptions and diagrams on next pages to connect the fan to your household wiring.
Fan installation MAKING THE ELECTRICAL CONNECTIONS WARNING: to avoid possible electric shock, be sure electricity is turned off at the main fuse box before wiring. Motor to receiver electrical connections: Connect the black wire from the fan to black wire marked “TO MOTOR L” from the receiver. Connect the white wire from the fan to the white wire marked “TO MOTOR N” from the receiver. Connect the blue wire from the fan to the blue wire marked “For Light” from the receiver.
Fan installation ATTACHING THE FAN BLADES NOTE: before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at fuse box. Turning power off using the fan switch may not be sufficient to prevent electric shock. P G F Insert the blade (P) through the slot in the bottom band, align the holes in the blade (P) and the bracket, secure with the blade screws (F) and fibre washers (G) provided. Repeat this procedure with the other blades (P).
Operation instructions J 2 0 9 Vol t Ba ttery 1 K 3 1. Install a 9-volt battery (K) (included ). 2. Restore power to ceiling fan and test for proper operation. Note: to prevent damage to transmitter (J), remove the battery if not used for long periods. 2 1 3 2 1 0 3 3. “1, 2, and 3 buttons: These three buttons are used to set the fan speed as follows: 1 = high speed 2 = medium speed 3 = low speed Forward Reverse 0 4. “0” button: This button turns the fan off. 5.
Blade balancing The following procedure should correct most fan wobble. Check after each step. Check that all blade and blade bracket screws are secure. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure from a point on the centre of each blade to the point on the ceiling. Measure this distance as shown in figure. Rotate the fan until the next blade is positioned for measurement.
Blade Balancing Kit The balancing kit should only be used if there is an unacceptable amount of fan wobble after completing all the steps in the user manual under “Fan Blades Assembly”. 1. Turn the fan on and set the speed control setting to a speed at which the wobble is the greatest. 2. Turn off the fan and allow it to come to a complete stop. Mark the blades with masking tape number 1-5.
Safety instructions PRODUCT MAINTENANCE Here are some suggestions to help you maintain your fan. WARNING: make sure the power is off at the electrical panel box before you attempt any repairs. Refer to the section “Making Electrical Connections.” Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.
