Quick Specification

Listed by
Underwriters
Laboratories
Specification Revised 10/20
PSB9120SF
GE Profile
™
Series 30 in. Single Wall Oven with Advantium
®
Technology
PREPARE THE OPENING (CONT.)
When installed over a single oven or a
warming drawer, allow at least 2" between
the two openings. This separation will
provide clearance for bottom overlap of
the Advantium and the other appliance
overlaps.
Construct a solid oven floor of 3/8" min.
thick plywood supported by 2 x 4 or 2 x 2
runners on all sides.
- The support must be level and rigidly
mounted, flush with the bottom edge of
the cutout.
NOTE: Additional clearances between
the cutouts may be required. Check to be
sure the oven supports above the Warming
Drawer location do not obstruct the required
interior depth and height. See Warming
Drawer installation instructions for details.
INSTALLATION OVER A BUILT-IN
OVEN AND WARMING DRAWER:
NOTE: Additional clearances between
the cutouts may be required. Check to be
sure the oven supports above the Warming
Drawer location do not obstruct the required
interior depth and height. See Warming
Drawer installation instructions for details.
CAUTION: For personal safety, the
mounting surface must be capable of
supporting the cabinet load, in addition
to the added weight of the oven and drawer,
plus additional oven loads.
PREPARATION WITH AN ACCESSORY DRAWER
PREPARE THE OPENING
The Advantium 120V can be installed in combination with other Built-
In appliances. Always follow each product's Installation Instructions to
compete the installation.
SINGLE OVEN INSTALLATION:
Order a 30" wide single oven cabinet or cut the opening in a wall to the
dimensions shown.
* For existing cutouts, a maximum
width of 28-1/2" is acceptable.
If the opening is slightly wider,
secure a furring strip on each side
of the cutout for securing the oven.
- The unit overlap on the top is 1/2"
but allow 5/8" clearance from top
edge of cutout. The unit overlap on
each side is 2−1/4" but allow 2−3/8"
clearance from side edges of cutout.
The unit overlap on the bottom is
5/8" but allow 3/4" clearance from
bottom edge of cutout.
- Oven overlaps will conceal cut edges on all sides of the opening.
NOTE: PSB9120 series Advantium can be installed below GE/GE
Profile non-downdraft gas and electric cooktops. It CANNOT be
installed below induction or Monogram (2GU3841385) gas cooktops.
NOTE: PSB9120 series Advantium oven comes with two lower trim
pieces. One is for use above 36-inch height installations and one is
for use below 36-inch installations. Use of the accessory drawer will
replace the bottom trim piece for applicable installations. Please see
installation instructions for full details.
25-1/4"
Min.
23-1/2"
21"
30"
Installation over Warming Drawer:
2" Min.
(3" recommended)
Per warming
drawer
requirement
36-3/4" Min.
from floor
1" Min.
above
toekick
Construct solid
bottom - Min. 3/8"
plywood supported
by 2x4 or 2x2
runners all four
sides
23-1/2"
Construct solid
bottom - Min. 3/8"
plywood supported
by 2x4 or 2x2
runners all four
sides
21"
30"
Installation over a Wall Oven and Warming Drawer:
2" Min.
(3" recommended)
2" Min.
Per oven
requirement
25-1/4"
Min.
Per warming drawer requirement
45-1/4" Min.
from floor
1" Min.
above
toekick
25-1/4"
23-1/2"
Construct base -
Min. 3/8" plywood
supported by 2x4
or 2x2 runners all
four sides.
21"
30"
36-3/4" Min.
from floor
1" Min.
above
toekick