GE Monogram® 42" Built-In Refrigerators Custom Options Guide and Installation Instructions With Custom Panel Dimensions and Trim Kit Installation Instructions These Monogram built-in refrigerators are designed to be customized with decorator door and grille panels. Field installed panels are required. Factory installed trim will accommodate 1/4" thick custom panels or optional Lexan® and Stainless Steel panel kits. Optional trim kits allow an even broader range of custom appearance options.
Before you begin - Read these instructions completely and carefully. IMPORTANT - Save these instructions for local inspector’s use. IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer - Be sure to leave these instructions with the Consumer. Note to Consumer - Keep these instructions with your Use and Care Book for future reference. WARNING This appliance must be properly grounded. See “Grounding the Refrigerator,” page 15. appareil doit être correctement mis à la terre.
Design Information DESIGN INFORMATION 42" Built-In Refrigerator Advance Planning Flush or Semi-Flush Enclosure Installations 3/4" 0" True Flush Installation In a flush installation, the refrigerator doors will align evenly with the front face of adjacent cabinet doors. The refrigerator blends into the surrounding cabinetry. Monogram built-in refrigerators can be installed flush with typical 24-3/4" deep cabinetry. When installed semi-flush, the case trim will conceal slight gaps around the enclosure.
DESIGN INFORMATION Design Information 42" Built-In Refrigerators Installation Examples Side panels are required whenever the sides of the refrigerator will be exposed. 1/2" to 3/4" side panels are normally set into place and fastened to adjacent cabinetry or to the back wall before rolling the refrigerator into the opening. Therefore, the rough-in dimensions must allow for side panel thickness.
Design Information Advance planning exterior appearance options These refrigerators are designed to be customized with decorator door and grille panels. Field installed custom door and grille panels are required. Factory installed trim accommodates 1/4" thick custom panels, Lexan® or stainless steel panel kits. Appearance options are accomplished through the use of one or more trim kits. Kits must be ordered separately. Door and grille panel sizes vary to accommodate the kit being used.
Custom Panel Dimensions 42" Built-In Refrigerator Front View (not to scale) CUSTOM PANEL DIMENSIONS Side View (not to scale) 24 3/4" ZIS42N (Non-dispenser) 41" Case Width 42" Overall Width 12 1/4" max 10-3/4" min 84 1/2" max 83" min 72 1/4" 4" *Finished Width Wall View (not to Scale) 7" 84 1/2" max 83-1/4" min Finished Opening Locate Grounded Electrical outlet Within Solid Area Above 5" 5" 18 3/8" Locate Water Supply Within the Shaded Area Below 74" From Floor to Bottom of Electrical Area 5"
Custom Panel Dimensions 42" Built-In Refrigerator Custom Door Panel Dimensions Using Standard Trim Freezer Panel ZIS42N (non-dispenser) Standard Trim with 1/4" Panels • 1/4" Panels: Cut panels to size. • Custom handles with 1/4" door panels require Trim Kit ZKH1 (or ZKHSS1 for tubular-stainless steel handles).
Custom Panel Dimensions 42" Built-In Refrigerator Custom Door Panel Dimensions CUSTOM PANEL DIMENSIONS Using Trim Kit ZKT42 3/4" thick panel with standard handle Freezer Panel Fresh Food Panel 67 15/16" 15 1/16" 25 1/16" Important: Maximum weight for fresh food panels is 50 pounds and 30 pounds for freezer door panels. Custom Grille Panel 41 1/2" A Over 1/4" Thick (3/4" max) Panel Grille Panel height can vary to fill installation height.
Custom Panel Dimensions 42" Built-In Refrigerator Custom Door Panel Dimensions Fresh Food Panel Freezer Panel ZIS42N (non-dispenser) • ZKT42 and ZKHT1 installed together provides for the installation of 3/4" custom door and grille panels, using a custom handle, of your choice. Order ZKHTSS1 for tubular stainless-steel handles. Cut panels to size, rout the handle side of the panels as shown below and install.
Custom Panel Dimensions CUSTOM PANEL DIMENSIONS 42" Built-In Refrigerator ZISW42D (white dispenser) ZISB42D (black dispenser) Front View (not to scale) Side View (not to scale) 24 3/4" 41" Case Width 42" Overall Width 12 1/4" max 10-3/4" min 84 1/2" max 83" min 72 1/4" 4" *Finished Width Wall View (not to Scale) 7" 84 1/2" max 83-1/4" min Finished Opening Locate Grounded Electrical outlet Within Solid Area Above 5" 5" 18 3/8" Locate Water Supply Within the Shaded Area Below 74" From Floor to B
Custom Panel Dimensions 42" Built-In Refrigerator Custom Door Panel Dimensions Using Standard Trim Freezer Panel Standard Dispenser Freezer Panel Custom Dispenser Fresh Food Panel 17 11/16" 16 5/8" 2 9/16" 36 7/8" 15 1/4 Standard Trim with 1/4" Panels • 1/4" Panels: Cut panels to size. • Custom handles with 1/4" door panels require Trim Kit ZKH1. When using ZKH1 with the standard dispenser trim, the length of the custom handle, top to bottom cannot exceed 11-3/4".
Custom Panel Dimensions 42" Built-In Refrigerator Custom Door Panel Dimensions CUSTOM PANEL DIMENSIONS Using Trim Kit ZKT42 3/4" thick panel with standard handle and/or ZWCD1 custom collar trim Freezer Panel Standard Dispenser Freezer Panel Custom Dispenser Fresh Food Panel 17 11/16" 16 11/16" 67 15/16" 2 5/16" ZISW42D (white dispenser) ZISB42D (black dispenser) • The ZKT42 trim kit provides for the installation of 3/4" custom door and grille panels, using the standard fulllength handle.
Custom Panel Dimensions 42" Built-In Refrigerator ZISW42D (white dispenser) ZISB42D (black dispenser) Custom Door Panel Dimensions Freezer Panel Standard Dispenser Freezer Panel Custom Dispenser Fresh Food Panel 17 11/16" 16 11/16" 67 15/16" 2 9/16" 37" 15 5/16" 15 5/16" 25 5/16" Important: Maximum weight for fresh food panels is 50 pounds and 30 pounds for freezer door panels.
Custom Panel Dimensions 42" Built-In Refrigerator CUSTOM PANEL DIMENSIONS Side Panel or Filler Options (not to scale) Side panels must be used whenever the sides of the refrigerator will be exposed. 23 9/16" 1/4" Side Panels Insert end of side panel into trim. For All Monogram Built-In Refrigerators 1/2" to 3/4" Side Panels Leading Edge Flush with Cabinet Front.
Installation 42" Built-In Refrigerator • Tinsnips to cut banding • Stepladder • 1-1/2" open-end wrench • Bucket • Level • Appliance Hand Truck • Tubing cutter Hardware Supplied • Special velcro adhesive strips for 1/4" side panels • 1/4-1/4 union with nuts • 1/4" panel foam spacers Materials Required • Water shut-off valve (optional but recommended) • Custom panels for fresh food, freezer compartments, grille panel • Side panels • Hardware for side panel installation.
Installation 42" Built-In Refrigerator Step 1 Remove Packaging CAUTION Refrigerator is much heavier at the top than at the bottom – be careful when moving. When using a hand truck, handle from side only. PRUDENCE PRODUCT INSTALLATION Le réfrigérateur est beaucoup plus lourd en haut qu'en bas. Il faut être prudent lors des déplacements. Si un diable est utilisé, il faut soulever le réfrigérateur sur le côté seulement. • Remove outer carton. – Carefully cut banding at the top and bottom.
Installation 42" Built-In Refrigerator Step 2A For Installations With A Reverse Osmosis System Only ATTENTION If the water supply to the refrigerator is from a Reverse Osmosis Water System AND the refrigerator also has a water filter, use the refrigerator’s filter bypass plug. Using the refrigerator’s water filtration cartridge in conjunction with the RO filter can result in hollow ice cubes and slower water flow from the water dispenser.
Installation PRODUCT INSTALLATION 42" Built-In Refrigerator Step 4 Roll Refrigerator Into Opening • Gently push refrigerator into opening with hands against front corners. The cardboard protective pad should be beneath the refrigerator. • Roll refrigerator into the opening until it is flush with adjacent cabinets. Step 5 Level Refrigerator All models have 4-point leveling. The front is supported by leveling legs, the rear is supported by wheels.
Installation 42" Built-In Refrigerator Step 7 OPTION 1 Secure refrigerator at the top WARNING Soffit Block ANTI-TIP PRECAUTIONS The refrigerator is heavy at the top and must be secured to prevent the possibility of tipping forward. ATTENTION PRODUCT INSTALLATION PRECAUTIONS CONTRE LES BASCULEMENTS Le réfrigérateur est beaucoup plus lourd en haut et il faut le maintenir en place pour éviter la possibilité de son basculement vers l'avant.
Installation PRODUCT INSTALLATION 42" Built-In Refrigerator Step 9 Connect power • Connect refrigerator power cord plug to properly grounded receptacle, accessible through the top right side of the grille opening. • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on. Step 10 Mount Top Grille Panel If you are using 3/4" thick custom panels, SKIP THIS STEP. See Custom Panel Dimensions for grille panel sizes.
ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles These instructions are divided into 2 options: Option 1—For non-dispenser and dispenser models using custom collar trim. Option 2—For dispenser model using the standard full-width trim. Tools and materials required: •#2 Phillips screwdriver •Drill and appropriate bits •Custom door panels •Custom handles •Safety glasses Kit contents ZKH1 INSTALLATION Parts List: A. Fresh food door extrusion B.
ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles Option 1 Installation Step 2 Locate position of handles ZKH1 INSTALLATION Door Extrusion 3/4" Min. 1-1/2" Max. Note: Handle must be located 3/4" to 1-1/2" from edge of extrusion. • Again, with both doors closed, check the location of • Slide custom panels into fresh food and freezer door the centerlines to be sure they are parallel to the edge frames. of the door, and level with opposite door.
ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles Option 1 Installation Step 3 Assemble panel, extrusion and handle Screw Extrusion Decorator Door Panel Decorator Door Panel Handle 3/4" Min. 1-1/2" Max. ZKH1 INSTALLATION Door Handle • Remove the door extrusions and door panels. • Drill 1/16" pilot hole through extrusion. • Drill clearance holes through the panel and extrusion. • Assemble the door panel, extrusion and custom handle.
ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles OPTION 2 For dispenser model using full-width trim • Open door to 90°. Remove the screws from the full-length aluminum handle of the freezer door. • Retain screws, discard handle. ZKH1 INSTALLATION Step 1 Remove handles Step 2 Remove trim Remove door panel trim above and below dispenser. Lift off dispenser trim. Retain screws and trim.
ZKH1 Trim Kit (For 1/4" Panels) Support for Custom Handles Option 2 Installation Step 4 Install custom handle • Drill clearance holes through the handle bracket and the dispenser trim. • Install screw(s) long enough to pass through the handle bracket, dispenser trim and into the custom handle. Dispenser Trim Handle Bracket ZKH1 INSTALLATION Handle Bracket Note: The custom handle must be installed against the handle bracket. The custom handle cannot exceed 11-3/4" length.
ZG2 Trim Kit Grille Panel Frame Adjustment FOR 83", 83-1/2" AND 84-1/2" INSTALLATION HEIGHTS • This kit provides optional side trim pieces for the original grille frame to fit 83", 83-1/2" or 84-1/2" installation heights. To change grille panel size: • Determine the installation height by measuring the enclosure from the floor to the underside of soffit. When there is no soffit, measure to the top of adjacent cabinets. • Adjust refrigerator case trim to desired height. See Product Installation.
ZKT42 Trim Kit 3/4" Custom Panels These instructions are divided into 2 options: Option 1—For non-dispenser and dispenser models using custom collar trim. Option 2—For dispenser model using the standard full-width trim. Tools and materials required: •#2 Phillips screwdriver •Stubby Phillips screwdriver •Drill and appropriate bits •Safety glasses •Custom panels Kit contents Parts List: Freezer Door A. Top trim B. Side trim C. Bottom trim A B C Fresh Food Door D. Top trim E. Side trim F. Bottom trim G.
ZKT42 Trim Kit 3/4" Custom Panels OPTION 1 For non-dispenser model or dispenser model using custom collar trim Step 1 Remove handles & trim Note: If a custom collar is to Important: When the bottom be used, order ZWCD1 trim kit. If a custom handle is to be used, order ZKHT1 trim kit. trim piece is removed, an aluminum shim secured to the bottom of the door can be seen. Do not attempt to remove this piece. • Attach the new 3/4" trim pieces on the top, hinge side and bottom using original screws.
ZKT42 Trim Kit 3/4" Custom Panels Option 1 Installation Step 3 Apply panel support brackets Back Side Door Panel Dimension A ZKT42–6-3/4" Hinge Sde Support Bracket Support Bracket Dimension B ZKT42–7-7/8" Bottom Edge Bottom Edge A Freezer Panels • Position support bracket on freezer panel, dimension A, from the hinge side edge. • Position support bracket on fresh food panel, dimension B, from the hinge side edge.
ZKT42 Trim Kit 3/4" Custom Panels Option 1 Installation Step 5 Adjust grille panel height The refrigerator is shipped with the top case trim secured at the 83" refrigerator height. • Loosen 2 screws on both sides and raise the top case trim to meet soffit height, from 83" to 84-1/2". • Tighten all 4 screws. Screws Top Case Trim Raise To Installation Height Important: Maintain 1-1/2" min. gap between top of doors and bottom of grille panel.
ZKT42 Trim Kit 3/4" Custom Panels OPTION 2 For dispenser model using full-width trim Step 1 Remove handles & trim • Open freezer door to 90°. • Remove the Phillips head screws from the full-length handles. • Open door fully to stop. • Remove screws from the aluminum trim, top, bottom and hinge side. • Remove the trim above and below the dispenser. • Retain screws and full-length handles. Discard original trim. • Attach the new 3/4" trim pieces at the top and hinge side using original screws.
ZKT42 Trim Kit 3/4" Custom Panels Step 4 Install panels ZKT42 INSTALLATION • Install the lower panel by slipping tabs into the slots on the underside of the dispenser trim. • Hold in position while fitting new bottom trim against the bottom of the door. Tabs should protrude through the bottom trim. • Install screws up through the bottom trim using stubby Phillips screwdriver. • Open door and install screws through the back side of the trim and into the panel at the hinge side.
ZKHT1 Trim Kit (For 3/4" Panels) Support for Custom Handles These instructions are divided into 2 options: Option 1—For non-dispenser and dispenser models using custom collar trim. Option 2—For dispenser model using the standard full-width trim. Tools and materials required: •#2 Phillips screwdriver •Stubby Phillips screwdriver •Drill and appropriate bits •Custom panels •Custom handles •Safety glasses Note: This kit must be used in conjunction with ZKT42 trim kit for 3/4" panel trim.
ZKHT1 Trim Kit (For 3/4" Panels) Support for Custom Handles Step 1 Temporarily mount door panels • Place the prepared 3/4"custom door panels on the bottom trim with support bracket tabs inserted into slots. • Push the panel back against the steel door, making sure panel is flush with hinge side trim. • Secure the panel to the trim temporarily by driving 2 screws through the back side of the trim at the top. • Slide door extrusion in between panel and steel door. Temporarily secure with 2 screws.
ZKHT1 Trim Kit (For 3/4" Panels) Support for Custom Handles Option 1 Installation Step 3 Assemble panel, extrusion and handle • • • • Remove the door extrusions and door panels. Drill 1/16" pilot hole through extrusion. Drill clearance holes through the panel and extrusion. Assemble the door panel, extrusions and custom handle. • Install screw(s) long enough to pass through the extrusion, door panel and into the handle. 3/4" Min. 1-1/2" Max.
ZKHT1 Trim Kit (For 3/4" Panels) Support for Custom Handles Option 1 Installation OPTION 2 For dispenser model using full-width trim Note: Optimal final appearance depends on careful routing depth. Do not exceed 1⁄4" routing depth. 1-13/16" Back Side 1-13/16" 1/4" Max. Handle Side Back Side Handle Side Freezer Panel Before you begin All 3 custom door panels must be routed to accommodate the door extrusions. Route the panels as illustrated, max.
ZKHT1 Trim Kit (For 3/4" Panels) Support for Custom Handles Option 2 Installation Step 2 Install custom handle • Drill clearance holes through the handle bracket and the dispenser trim. • Install screw(s) long enough to pass through the handle bracket, dispenser trim and into the custom handle. Dispenser Trim Handle Bracket Handle Bracket Dispenser Trim Custom Handle Step 3 Mount assembled dispenser trim • Mount assembled dispenser trim with handle onto the door.
ZKHSS1 for 1/4" Panels Tubular Stainless Steel Handles This kit provides for the installation of Stainless Steel custom handles on 1/4" thick decorator door panels. The door extrusions allow these custom handles to be secured to the door structure, rather than to the custom panels. This kit contains all the necessary parts for dispenser and non-dispenser models.
ZKHSS1 for 1/4" Panels Tubular Stainless Steel Handles Step 2: Match Handle Extrusions to Handle • Cut a piece of corrugated to use as a pad to protect the panel finish. Use 1/2" thick section of plywood to protect flooring when drilling. • Place custom panels on the pad, appearance side down. Top End Note: If panels are wood, be sure to note which end is the top so that wood grain is in the correct direction on both (or all 3) panels.
ZKHSS1 for 1/4" Panels Tubular Stainless Steel Handles Step 2A: FOR STAINLESS STEEL PANELS Step 3: Install Standoffs onto Handles If you are installing these handles onto Stainless Steel panels: Use extreme caution if you are drilling through stainless steel panels. Stainless panels must be handled gently. Do not kneel on stainless steel panels. It will leave a permanent dent. Do not remove protective plastic covering until final installation.
ZKHSS1 for 1/4" Panels Tubular Stainless Steel Handles Step 4A: Install Handles and Panels Door Handle FOR STAINLESS STEEL PANELS Extrusion Screw Spacer Ring 1/4" Stainless Panel Corrugated For Stainless Panels: • Press foam pads against steel doors to temporarily reduce thickness. • Crimp top and bottom edges of corrugated. • Slide corrugated onto doors, leave about 1/4" gap between edge of corrugated and hinge side. Note: Panels have a protective plastic covering.
ZKHTSS1 for 3/4" Panels Tubulor Stainless Steel Handles This kit provides for the installation of Stainless Steel custom handles on 3/4" thick decorator door panels. The door extrusions allow these custom handles to be secured to the door structure, rather than to the custom panels. This kit contains all the necessary parts for dispenser and non-dispenser models.
ZKHTSS1 for 3/4" Panels Tubulor Stainless Steel Handles Step 1: Remove Handles • Open doors to 90°. Remove the screws from the full-length handles of both doors. • Retain screws, discard handles. Note: If a custom collar is to be used, order ZWCD1 Trim Kit for 36" and 42" wide models. Order ZWCD2 for 48" wide models. Step 2: Match Handle Extrusions to Panels • Cut a piece of corrugated to use as a pad to protect the panel finish. Use 1/2" thick section of plywood to protect flooring when drilling.
ZKHTSS1 for 3/4" panels Tubular Stainless Steel Handles Step 3: Install Standoffs onto Handles Step 4: Install Handles • Place a handle standoff on each attachment post along the handle. Position the screw hole on the standoff to point to the floor. • Install set screws into the bottom of each standoff, using the Allen wrench provided. The standoff should be tight against the handle. Screw Allen Wrench • Start mounting screws through the extrusion and just through the custom panel.
ZKHTSS1 for 3/4" Panels Tubular Stainless Steel Handles Step 5 Install Assembled Panels (continued) For models with full width dispenser trim and 2 piece freezer panels: It is best that 2 people perform this step. • Carefully, lift the assembled panel to the case trim. Hold both panels so they do not twist the extrustion. • Insert the support bracket tabs into the bottom trim. • Push and hold the panel back against the steel door. • Reinstall original screws into the door extrustion.
ZWCD1 Trim Kit Custom Dispenser Collar Tools and materials required: •#2 Phillips screwdriver •Drill and appropriate bits •Custom door panels •Safety glasses Kit contents Parts List: A. Collar trim (Both black and white trim included) B. Top bracket C. Bottom bracket D. Screws (2) B C D This kit provides for the use of a custom dispenser collar trim, replacing the standard full-width trim. This kit can be used alone, or combined with one or all other trim kits.
ZWCD1 Trim Kit Custom Dispenser Collar Cut dispenser hole and rout door panel The use of this custom collar trim requires that the hole for dispenser be located and cut very accurately. 3/4" door panels must be routed on all 4 sides of the dispenser cutout. Rout the back side of the panel 1/4" deep and 7/8" wide, flush with the edge of the cutout. Note: 1/4" door panels do not 9 7/16" 12 5/16" 7/8" Wide Rout The Cutout is 9 7/16" wide by 12 5/16" high.
Note: While performing installations described in this book, safety glasses or goggles should be worn. To obtain specific information concerning any Monogram product or service, call GE Answer Center® consumer information service at 800.626.2000–any time, day or night. For Monogram local service in your area, call 1-800-444-1845. TM Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. ® Monogram.
