Design Guide with Installation Instructions 36” Built-In French Door, Bottom-Freezer Refrigerators 31-49074 224D3560P002 12-14 GE monogram.
Safety Information BEFORE YOU BEGIN If you received a damaged refrigerator, you should immediately contact your dealer or builder. Skill Level – Installation of this refrigerator requires basic mechanical, carpentry and plumbing skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Owner’s Manual for warranty information. Read these instructions completely and carefully.
Consignes de Sécurité Ce symbole représente une alerte de sécurité. Ce symbole vous avise de dangers possibles pouvant causer la mort, des blessures ou autres. Tous les messages de sécurité seront précédés du symbole d’alerte de sécurité ainsi que des mots « DANGER », « AVERTISSEMENT » ou « MISE EN GARDE ». Ces messages sont les suivants : DANGER Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, entraînera des bles sures graves, voire la mort.
Contents Safety Planning Guide The Installation Space Dimensions and Clearances 130° Door Swing 90° Door Swing Side Panels Installation Instructions Tools, Hardware, Materials Grounding the Refrigerator Step 1. Remove Packaging Step 2. Install Water Line Step 2A. Water Line with Reverse Osmosis System Step 3. Install Side Panels 2-3 Step 4. Anti-Tip Procedures Step 5. Level Refrigerator Step 6. Secure Unit to Wall Step 7. Alternate Anti-Tip Procedure Step 8. Secure Refrigerator to Cabinetry Step 9.
Design Guide DIMENSIONS AND CLEARANCES THE INSTALLATION SPACE The finished cutout width must be 35-1/2”. 35-1/2" Finished Width Wall View 2-5/16" 10" 84-1/2" Max.
Design Guide Refrigerator Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips.
Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips.
Design Guide SIDE PANELS Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4” side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer. • Cut a notch in the top front corner as shown to allow clearance for corner keys in the front side trim. 24" * Depending on installation height.
Installation Instructions TOOLS REQUIRED HARDWARE SUPPLIED • Tinsnips to cut banding • Stepladder • Bucket • Level • Appliance Hand Truck • Tubing cutter • 7/16” open-end wrench • #2 Phillips screwdriver • Drill and appropriate bits • 5/16”, 7/16” socket • Safety glasses • 1-1/4” open end wrench • Pliers • 1/4” ratchet • Water filter bypass plug • Anti-Tip brackets • 1/4” nut and ferrule • Flush inset bracket pack • Case trim(s) FLOORING For proper installation, this refrigerator must be placed on a lev
Installation Instructions STEP 1 REMOVE PACKAGING WARNING • The unit is secured to the skid with 2 full-length tie-down straps. Remove the ten 5/16” bolts from the base channels in the tieRemove 5 downs. base channel • Remove the four 7/16” bolts on each bolts securing the straps to side the skid. NOTE: DO NOT ATTEMPT TO ROLL UNIT OFF SKID.
Installation Instructions STEP 4 ANIT-TIP PROCEDURE (CONT) STEP 2A WATER LINE INSTALLATION WITH A REVERSE OSMOSIS SYSTEM • The kit supplied with the unit contains 2 lag bolts and 4 toggles with bolts. The wall bracket will be attached to the wall in 4 places. • Measure the opening where the unit is to be installed. Mark the center with a vertical line. • Measure up 81 1/2” from the floor. Mark this point on the wall. • Using a level, draw a horizontal line on the wall at this height.
Installation Instructions STEP 4 ANIT-TIP PROCEDURE (CONT) STEP 4 ANIT-TIP PROCEDURE (CONT) • The anti-tip wall bracket has a series of holes. Select 2 holes that match with the located studs. Make sure the holes selected are on the center of the studs. Mark the wall at these points. • Mark an additional hole at each end of the bracket. If one of the studs is closer to the end of the bracket, mark an additional hole towards the center of the bracket.
Installation Instructions STEP 6 SECURE UNIT TO WALL STEP 5 LEVEL REFRIGERATOR • The “L” rod can be found in the upper left corner of the unit in the access compartment. Look through the access compartment to make sure the rod lines up with the anti-tip bracket. • There are 2 washers and a hair pin cotter with the rod. Remove the washers and hair pin cotter from the end of the rod. • Rotate and move the “L” rod into the slot in the anti-tip bracket tab.
Installation Instructions STEP 7 ADJUST DOOR SWING STEP 8 SECURE REFRIGERATOR TO CABINETRY NOTE: This refrigerator has a 2-position door stop. When space does not allow the door to swing open fully to 130°, you may change the door swing to a 90° opening. Skip this step if door opening is satisfactory for your installation situation. Whenever possible, perform this step in addition to the Anti-Tip Procedures for anti-tip security. The refrigerator must be secured to prevent tipping.
Installation Instructions STEP 10 CONNECT POWER STEP 9 CONNECT WATER SUPPLY • Check to be sure the power cord is plugged into the receptacle. Raise Grille Panel Electrical Outlet House Water Supply • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on. • The temperature controls are preset at 37°F for the fresh food section and 0°F for the freezer. • Allow 24 hours to stabilize before making adjustments.
Installation Instructions STEP 12 INSTALL TOEKICK INSPECT FINAL INSTALLATION • Locate the 2 supplied toekicks (shipped taped to the side of the refrigerator). Install the toekick assembly with the 2 screws provided, adjust to the desired height and tighten the screws. Check door alignment Stand back away from the refrigerator to inspect the final installation. • Installation or the addition of heavy door panels may have caused the doors to move slightly out of alignment.
Notes 17
Notes 18
Notes 19
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. GE Appliances 31-49074 224D3560P002 12-14 GE Appliance Park Louisville, KY 40225 GEAppliances.
