GE Security Legend User Manual
Copyright Copyright © 2005, GE Security Inc. All rights reserved. This document may not be copied in whole or in part, or otherwise reproduced except as specifically permitted under US copyright law, without the prior written consent from GE. Document number/revision: 1052027A. Disclaimer The information in this document is subject to change without notice. GE, in keeping pace with technological advances, is a company of product innovation.
iii Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Conventions used in this document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Safety terms and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv Legend DRAFT User Manual Alarms menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Programming tips for dome alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Summary screen ( Alarms | Summary ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Introduction This is the GE Legend User Manual. It provides an overview of the product and detailed instructions explaining how to program and operate all models. There is also information describing how to contact technical support if you have questions or concerns. For installation instructions, refer to the Legend Installation Manual.
2 Legend User Manual Overview The Legend™ dome is programmed through a graphical programming interface. The end-user’s system administrator and/or the installer will do the programming. Be aware that the installer would have turned on the passcodes for the system during installation, if they were to be used during normal operation. Legend is the next generation PTZ dome camera that maintains and enhances many of the features of CyberDome that you have come to rely on.
3 Accessing the programming interface If passcodes were turned on during installation or later, access to the programming interface will be passcodeprotected. You must log on to program the dome. Otherwise, you will be taken directly to the main programming screen. The passcodes control who has access to the features of your dome. See Passcode screen ( Setup | Passcode ) on page 11. The steps for accessing the programming interface from all GE keypads are similar.
4 Legend User Manual 4. At the enter site number display, enter the number for the camera site you are programming. This is a 3-digit number (for example, 007, 021, 243). You can enter one, two, or three digits and press set ( ). 5. Continue entering commands with the joystick. Figure 7. Enter site number display ENTER CAMERA SITE NUMBER _ _ _ "BACK Figure 8. See Monitor For Menus display SEE MONITOR FOR MENUS HOLD SEQ (3 SEC) TO EXIT 6.
5 Navigating the programming interface While in the programming interface, the joystick of your keypad operates in two modes depending upon what your current action is. While moving among the menus of the programming interface, the joystick is a simulated mouse and you enter commands using the joystick. While controlling live video, the joystick is a video controller.
6 Legend User Manual Keypad shortcuts The following are keypad shortcut commands carried over from CyberDome programming. Where keypad shortcuts exist for a feature, such as setting presets, you can use keys from the keypad, instead of menus from the programming interface, to program the feature. See Table 1. You can then go into the programming interface and customize the programmed feature with titles and other attributes. Table 1.
7 Basic programming The dome is ready to operate with its defaults. Presets and ShadowTours are the most commonly used programmable features. This section provides the step-by-step instructions for programming presets and ShadowTours. For more challenging surveillance conditions, you can take full advantage of the dome’s programming features. See Advanced programming on page 10. Presets You can set presets from the keypad or with the programming interface.
8 Legend User Manual Programming presets with the programming interface To program presets with the programming interface: 1. Access the programming interface. (For details, see Accessing the programming interface on page 3.) a. Press and hold the set ( ) key on the keypad until you hear a beep and the programming code display appears on the keypad’s LCD. b. Press the 9, 5, 1, and seq keys on the keypad. c. Press 3 to select CAMERA.
9 ShadowTours You have a total of 16 ShadowTours (totaling 20 minutes) that you can define for the dome. A ShadowTour is a tour that the camera learns by recording your manual operation of the camera. Use a keypad to manually direct the camera through the desired PTZ movements. The camera stores those movements in memory. The recorded tour can be replayed at any time. To program ShadowTours with the programming interface: 1. Access the programming interface.
10 Legend User Manual Advanced programming You will be using the graphical programming interface to program the dome. Keypad shortcuts do exist for some programmable features. These keypad commands are carried over from CyberDome programming (see Keypad shortcuts on page 6). Where keypad shortcuts exist for a feature, such as setting presets, you can use keys from the keypad or you can use menus from the programming interface to program the feature.
11 Figure 16. Memory screen ( Setup | Memory ) CAUTION Clearing memory replaces your custom programmed settings with the factory default settings. Select memory (clear options) You can clear all or specific portions of your dome’s programming, which is saved in the housing’s site-tied memory. After selecting an option, select Clear. Choices are Clear all (default), Clear setup options, Clear presets, Clear macros, Clear ShadowTours, Clear areas, Clear alarm actions, and Clear privacy masks.
12 Legend User Manual You can turn on one installer passcode, one admin passcode, and one operator passcode. They have the following permissions: • • • Installer: The installer passcode allows access to all dome features. Admin: The admin passcode allows access to all dome features, except passcodes and firmware updates. Operator: The operator passcode allows no access until it is granted access to specific features on an area-by-area basis. Figure 17.
13 Title/Date screen ( Setup | Title/Date ) The Title/Date screen establishes the camera number, title, and installation date for the dome. Figure 18. Title/Date screen ( Setup | Title/Date ) Note: Remember to select OK to save any changes you make on the page. Camera number The programming interface reads the address number set in the camera with the rotary address switches and displays that address as the camera number. The camera number is not editable.
14 Legend User Manual Title font size The camera title will appear on screen in the font size selected. Choices are as shown. Default is 26 pt. Title font weight The camera title will appear on screen in the font weight selected. Choices are as shown. Default is Bold. Block color You can create a block (background) that offsets the camera title from the video behind it. The block will appear on screen in the color selected. Choices are as shown. Default is Black.
15 Net mask Enter the subnet mask address of the network subdivision that the dome is assigned to. Server Enter the IP address of the network server. If used, enter the IP address of the TFTP host. See Firmware Update screen ( System | Firmware Update ) on page 61. Gateway Enter the address of the gateway between the dome and the network server. MAC address Provided as the unique address of the dome, the MAC address allows you to connect to the dome before you have set up its network addressing.
16 Legend User Manual High temp warning The High temp warning feature allows you to display a high-temperature reading on the monitor screen when the temperature in the dome has reached a set high threshold. Place a check mark in the check box to display this warning. The threshold and duration features then become available. Threshold (high-temp) The high-temperature threshold feature allows you to set the high boundary of the allowable temperature range for the dome.
17 Pan The Pan feature displays the pan coordinate of the dome. Choices are Off, Bearings, Degrees 360 (default), and Degrees +/- 180. Figure 22. Pan coordinates Pan coordinates: Bearings/Degrees 360°/Degrees ±180° N/0°/0° NW/315°/-45° NE/45°/+45° W/270°/-90° E/90°/+90° SW/225°/-135° SE/135°/+135° S/180°/+180° Tilt The Tilt feature displays the tilt coordinate of the dome. Choices are Off, Degrees 180 (default), and Degrees +/- 90. Figure 23.
18 Legend User Manual Set north The Set north button programs the north (0°) point for the camera. Note: When using bearings for your pan coordinates, they are easier to interpret if you set the true due north point as the 0° point. If, however, you are using degree pan coordinates, you can set the 0° point anywhere along the scale. For example, you may want the 0° point to be a main entrance of a facility. To program the north point: 1. Select Set north.
19 Camera menu The dome is ready to operate with its default settings. The defaults are optimized for general applications. You can customize the dome’s performance for challenging applications by changing the dome’s camera features in the Camera menu. One camera feature, however, is adjusted with the keys on your keypad. Backlight compensation is adjusted with the iris control key, while you are in auto exposure mode.
20 Legend User Manual Figure 27. Privacy masks screen ( Camera | Privacy Masks ) Note: Remember to select OK to save any changes you make on the page. Mask number The Mask number drop-down box allows you to select the mask number that you want to program. Mask title The Mask title box allows you to give your masks unique titles. Default numerical titles are provided. There is a 60-character limit for all titles, but be aware of how much video you want to cover with your titles.
21 Mask color You can customize the color of each mask. Individual masks will appear on screen in the color selected. Choices are Gray (default) and Red. Show The Show button displays the mask that is currently selected by the mask number field. The screen will say “Privacy mask preview” in the upper left corner. Press iris +/-, esc, or set ( ) to return to the menus. Program The Program button programs the mask. There are two screens for programming masks.
22 Legend User Manual Settings screen ( Camera | Settings ) Page1 page ( Camera | Settings | Page1 ) Figure 28. Page1 page ( Camera | Settings | Page1 ) Note: Remember to select OK to save any changes you make on the page. Day/Night Day/Night is a camera feature that switches the camera mode from color (day) to monochrome (night) and removes the IR cut filter, which increases the camera’s sensitivity in low light. It also allows the camera to function with IR lighting.
23 White balance White balance is another camera feature that compensates for lighting conditions. It adjusts the quality of all of the colors in the video by balancing the colors to achieve the truest white possible for the available lighting conditions (Tungsten, fluorescent, natural). This feature is used instead of a more general color temperature setting. To correctly set the white balance, focus the camera on a white object. Choices are Auto (default), Indoor, Outdoor, ATW, and Manual.
24 Legend User Manual Exposure: Control Control is an exposure feature that determines which exposure control setting takes priority in automatic and manual operation. Note: The Day/Night feature works only if the Exposure feature is set to Auto or Return to auto. Also see Interrelationship between the Exposure and Day/Night features on page 64. Choices are Auto, Shutter, Iris (default), and Manual. See Table 2 on page 24 and Table 3 on page 25 for details about the exposure settings.
25 Table 2. Exposure control settings Exposure control setting Operation Automatic adjustments Auto • Iris setting (F-stop) • Shutter speed (sec) • Gain (dB) Shutter Iris Manual • Iris setting (F-stop) • Gain (dB) • Shutter speed (sec) • Gain (dB) N/A • Lowest shutter speed • Return to auto Return to auto • Lowest shutter speed • Return to auto Except when the shutter speed is below 1/60s NTSC or 1/50s PAL. Available controls Table 3.
26 Legend User Manual Page2 page ( Camera | Settings | Page2 ) Figure 29. Page2 page ( Camera | Settings | Page1 ) Note: Remember to select OK to save any changes you make on the page. Phase lock enabled Phase lock enabled is a camera feature that allows synchronization of the video signal to reduce the effect of picture roll on analog video switchers. By default, the phase lock is off. As such, each camera is synchronizing its video signal to its own internal clock crystal.
27 Digital zoom limit Digital zoom is an electronic camera feature that increases the apparent size of images beyond the magnification of the camera’s optical lens. Because image information is not also increased, there is some loss of image resolution. So test the different settings for suitability. Selecting too high of a digital zoom can result in the loss of video clarity for some scenes. To test: Select a setting and use your keypad’s zoom key to zoom in and out.
28 Legend User Manual Tilt down limit Tilt down limit is a feature that sets a programmable stop for the camera at the lowest point that you want it to tilt down. By default, the pan and tilt limits are off. Programming them turns them on. Note: Pan left limit Pan left limit is a feature that sets a programmable stop for the camera at the leftmost point that you want it to pan left. By default, the pan and tilt limits are off. Programming them turns them on.
29 Actions menu You can program a variety of custom actions for each dome. Your custom actions include 127 preset positions, 16 ShadowTours, 32 macros, and 120 areas. You can edit the title and description of any action and you can reassign the positions of existing presets. The keypad’s joystick will function as a simulated mouse or video controller at different times during the programming of your actions. Figure 30.
30 Legend User Manual Summary page ( Actions | Presets | Summary ) The summary page provides the number and title of all 127 presets (1 through 127) that are available for the dome, whether or not they are programmed or titled. Figure 31. Summary page ( Actions | Presets | Summary ) No. The No. column of the summary page lists all 127 presets (1 through 127) in numerical order, whether or not they are programmed. Title The Title column of the summary page lists the titles of all 127 presets.
31 Edit page ( Actions | Presets | Edit ) The Edit page is where you program your presets. You can select any preset number, whether previously programmed with a preset position or not. You can reassign new positions to existing presets. After you have selected a number and established the duration of the preset title, you will select the POS button and program the preset position.
32 Legend User Manual POS (position) The POS (position) button programs the preset. There is one screen for programming presets. To program a preset: 1. Select POS. The programming interface will be replaced by a full screen of live video that asks you to set the desired position for the preset. 2. At the live video screen, use the joystick to pan, tilt, and zoom the camera to the desired position. 3.
33 Title POS The preset title will appear on screen in a default position on the monitor screen (bottom center), but you can reposition it with the Title POS button. Be aware of where you already have other titles (camera, privacy masks, tours, macros, areas, and alarms) positioned. To set the position of the preset title: 1. Select Title POS. 2. Move the joystick to move the title to the desired position. 3.
34 Legend User Manual Figure 34. Advanced page ( Actions | Presets | Advanced ) Note: Remember to select OK to save any changes you make on the page. No. The No. drop-down box allows you to select the preset number that you want to continue programming. Title The Title box shows you the existing title for the selected preset number. You can customize the default title on the Display page.
35 Night mode For the duration of this preset, you can change the camera’s Day/Night setting. Day/Night is a camera feature that switches the camera mode from color (day) to monochrome (night) and removes the IR cut filter, which increases the camera’s sensitivity in low light. It also allows the camera to function with IR lighting. It is programmed under Camera | Settings (see Settings screen ( Camera | Settings ) on page 22).
36 Legend User Manual White (white balance) For the duration of this preset, you can change the camera’s White balance setting. White balance is a the feature that compensates for lighting conditions. It adjusts the quality of all of the colors in the video by balancing the colors to achieve the truest white possible for the available lighting conditions (Tungsten, fluorescent, natural). This feature is used instead of a more general color temperature setting.
37 Exposure For the duration of this preset, you can change the camera’s Exposure setting. Exposure is a feature that establishes what controls the light coming into the camera through the lens. Note: The Day/Night feature works only if the Exposure feature is set to Auto or Return to auto. See Interrelationship between the Exposure and Day/Night features on page 64. Choices are Auto (default), Shutter, Iris, and Manual.
38 Legend User Manual ShadowTours screen ( Actions | ShadowTours ) You have a total of 16 ShadowTours (totaling 20 minutes) that you can define for the dome. Figure 35. ShadowTours screen ( Actions | ShadowTours ) Note: Remember to select OK to save any changes you make on the page. No. The No. drop-down box allows you to select the ShadowTour number that you want to program. Title The Title box allows you to give your ShadowTours unique titles. Default numerical titles are provided.
39 Title font weight The ShadowTour title will appear on screen in the font weight selected. Choices are as shown. Default is Bold. Block color You can create a block (background) that offsets the ShadowTour title from the video behind it. The block will appear on screen in the color selected. Choices are as shown. Default is Black. Block transparency You can set the block (background) to be a solid color or a transparency. The block will appear on screen in the transparency selected.
40 Legend User Manual Macros screen ( Actions | Macros ) You can program 32 macros per dome. Macros are any preset tour or programmed routine. Each macro can contain up to 16 steps. The step, type, and type number options will appear on all macro programming screens. The step type determines what additional options are available for programming. Program page ( Actions | Macros | Program ) Figure 36.
41 Speed (with Preset or Tour) The Speed option allows you to set how fast the camera will move to the preset step. Choices are Slow, Medium, Fast, and Max. Transition (with Preset or Tour)The Transition option allows you to set how the video will be seen on the monitor screen during a preset step. Choices are Freeze (default) and Zoom out. • The Freeze feature freezes the last image on the monitor screen while the camera is moving. A static image will show on the monitor screen until the camera stops.
42 Legend User Manual Display page ( Actions | Macros | Display ) Figure 37. Display page ( Actions | Macros | Display ) Note: Remember to select OK to save any changes you make on the page. No. The No. drop-down box allows you to select the macro number that you want to continue programming. Title The Title box allows you to give your macros unique titles. Default numerical titles are provided.
43 Block color You can create a block (background) that offsets the ShadowTour title from the video behind it. The block will appear on screen in the color selected. Choices are as shown. Default is Black. Block transparency You can set the block (background) to be a solid color or a transparency. The block will appear on screen in the transparency selected. Choices are as shown. Default is No color. Areas screen ( Actions | Areas ) Areas are similar to privacy masks.
44 Legend User Manual Display page ( Actions | Areas | Display ) Figure 39. Display page ( Actions | Areas | Display ) Note: Remember to select OK to save any changes you make on the page. No. The No. drop-down box allows you to select the area number that you want to program. Title The Title box allows you to give your areas unique titles. Default numerical titles are provided. There is a 60-character limit for all titles, but be aware of how much video you want to cover with your titles.
45 Title font size Individual area titles will appear on screen in the font size selected. Choices are as shown. Default is 26 pt. Title font weight Individual area titles will appear on screen in the font weight selected. Choices are as shown. Default is Bold. Block color You can create a block (background) that offsets the title from the video behind it. Individual area blocks will appear on screen in the color selected. Choices are as shown. Default is Black.
46 Legend User Manual Alarms menu You can program up to eight alarm inputs and two relay outputs per dome. Each alarm input can call up (display) any preset, macro (preset tour or programmed routine), or ShadowTour. The eight alarms are numbered from 1 to 8. Programming tips for dome alarms Legend domes do not handle alarms the same way as most other alarm equipment. You need to be aware of the differences to manage the dome’s inputs and outputs effectively. Here are some key concepts.
47 Figure 40. Alarms menu Summary screen ( Alarms | Summary ) You can view the status of alarms from the summary page. Alarms are presented in numerical order with whatever titles have been assigned. Statuses are as follows: • • On: Status shows as On if the contact for the alarm is in its active state. So, for a N/O (normally open) contact that is closed, the status reports as on, because it is in its activated, abnormal state.
48 Legend User Manual Figure 41. Summary screen ( Alarms | Summary ) Summary: No. The No. column of the summary page lists all alarms in numerical order, whether programmed or not. The eight alarms are numbered from 1 to 8. Summary: Title The Title column of the summary page lists the titles for all available alarms, whether programmed or not. Summary: Status The Status column of the summary page lists the status of each programmed alarm as either on (active) or off (inactive).
49 Contact Setup screen ( Alarms | Contact Setup ) The Contact Setup screen is where you define the individual alarms. For tips, see Programming tips for dome alarms on page 46. Figure 42. Contact Setup screen ( Alarms | Contact Setup ) Note: Remember to select OK to save any changes you make on the page. Contact no. The Contact no. drop-down box allows you to select the alarm number that you want to program. Contact type Alarm contacts are identified as N/O (normally open) or N/C (normally closed).
50 Legend User Manual Relay 2 Each Relay feature associates one relay action with an alarm. Relays can be used to trip such devices as speakers, doors, and DVMRs. Each alarm can be programmed with up to three actions (one dome action and two relay actions). You can set both relays to activate with an alarm. An action is not required. Choices are No action (default), On, and Off. Duration The Duration feature defines how long the relay is active.
51 Display screen ( Alarms | Display ) The Display screen is where you define the appearance of the block of alarms and relays that displays on the monitor screen. To display the alarm block at all times, you must set the Alarm box content to All status and the Alarm box duration to Indefinite. Figure 44. Display screen ( Alarms | Display ) Note: Remember to select OK to save any changes you make on the page. Alarm title This feature does not title the individual alarms.
52 Legend User Manual Title font weight Alarm titles will appear on screen in the font weight selected. Choices are as shown. Default is Bold. Note: If All status is selected for the Alarm box content feature, then the selected Title font weight is overridden and all alarms are listed in the alarm box with normal weight and only the active alarms are listed with bold weight. Block color You can create a block (background) that offsets the alarm block from the video behind it.
53 Relay State screen ( Alarms | Relay State ) Figure 45. Relay State screen ( Alarms | Relay State ) Note: Remember to select OK to save any changes you make on the page. Summary: Name The Name column of the summary page lists both relays in numerical order, whether programmed or not. The two relays are numbered 1 and 2. Summary: State The State column of the summary page lists the status of each programmed relay as either on (active) or off (inactive).
54 Legend User Manual Control menu You can program a variety of general camera features that control each dome. These general features include a specific operation for the camera to execute when it is first powered up (Power-on), a specific operation for the camera to execute when the keypad has been inactive for a duration of time (Resume), and speed settings for panning, tilting, autopanning, and moving between presets. Figure 46.
55 Figure 47. Command Map screen ( Control | Command Map ) Note: Remember to select OK to save any changes you make on the page. Summary The Summary feature lists what actions are currently assigned to each command. The Summary feature lists presets and tours separately, according to whichever list (preset or tour) you currently have selected under the Command option. Command The Command feature changes the group of commands listed in the summary between presets and tours.
56 Legend User Manual Power-on and Resume screen ( Control | Power-on and Resume ) Figure 48. Power-on and Resume screen ( Control | Power-on and Resume ) Note: Remember to select OK to save any changes you make on the page. Power-on operation Power-on defines the first operation that the dome performs after it is powered up and initialized. Choices are Off (default), Preset, Macro, ShadowTour, and Autopan.
57 Speeds/Tracking screen ( Control | Speeds/Tracking ) Figure 49. Speeds/Tracking screen ( Control | Speeds/Tracking ) Note: Remember to select OK to save any changes you make on the page. Manual PTZ: Max pan speed (deg/s) The Max pan speed is a feature that sets the fastest the camera will move (in degrees per second) while manually panning. Choices are 100 through 250 (default) in increments of 10.
58 Legend User Manual Autopan speed The Autopan speed is a feature that sets how fast the camera moves while autopanning. Choices are Slow (default), Medium, and Fast. These settings are scaled according to the settings set for the slow, medium, and fast Macro and autopan speed settings. If the numbers in the Macro and autopan speed setting boxes are lower, then the corresponding Autopan speed settings will be slower.
59 System menu You can access diagnostics, status, and communication logs of your system’s features through the System menu screens. Under Diagnostics, you can see what temperature your dome is operating at. Under Status, you can see a detailed listing of your dome’s site (camera) information such as title and IP address, customized settings, alarm status, and customized presets, tours, masks, and macros.
60 Legend User Manual Diagnostics screen ( System | Diagnostics ) The Diagnostics screen provides the operating temperature of your dome. Figure 51. Diagnostics screen ( System | Diagnostics ) Status screen ( System | Status ) The Status screen provides a detailed listing of your dome’s site (camera) information such as title and IP address, customized settings, alarm status, and customized presets, tours, masks, and macros. Figure 52.
61 Logs screen ( System | Log ) The Logs screen provides a history of the command, protocol, and motor messages of the dome’s most recent operations. Level 1 logs list the most restrictive and important messages, level 2 list those of medium restriction and importance, and level 3 lists those of least restriction and importance. Figure 53. Log screen ( System | Log ) Firmware Update screen ( System | Firmware Update ) There are two ways to reload or update the software in your dome.
62 Legend User Manual Figure 54. Firmware Update screen ( System | Firmware Update ) To update (or reload) the dome’s software using the Firmware Update feature, see Figure 54 and do the following: CAUTION For all installations, heed these cautions: • DO NOT interrupt the reload/update purpose until it has completed. Don’t use the keypad, don’t break the network connection, and don’t cycle the power to the dome.
63 System operation Legend domes are controlled from at least one controller keypad. Refer to your keypad’s manual for instructions on operating the dome. This chapter lists some general guidelines and restrictions for operating the Legend domes. Setting autopan limits Figure 55. No E-flip with autopan limits 0° (+90°) Legend Legend When setting autopan limits, be aware that you must set both the right and left limit in the same tilt hemisphere.
64 Legend User Manual Calling up presets from a keypad Most keypads have a limited number of preset numbers they can call. If you have a GE KTD-405 keypad with firmware version 1.2.09 or later, then you can call up all 127 preset numbers (1 through 127) directly from the keypad. If, however, you have a GE KTD-405 keypad with an earlier version of firmware, then you can use the keypad to call up only the first 63 preset numbers (1 through 63).
65 Troubleshooting, maintenance, support This section provides information to help you diagnose and solve various problems that may arise while configuring or using your GE Security product and offers technical support contacts in case you need assistance. See Contacting technical support on page 67. Troubleshooting your Legend system Common programming issues Is the programming interface not responding? • • First, reboot the camera with the keypad using the procedure in Rebooting the dome on page 63.
66 Legend User Manual • • IP for domes: 192.168.208.XXX, where XXX is the site number (or camera address) of the dome. Subnet mask for domes: 255.255.255.0 2. Copy the update file from the Legend system CD to your computer. It will usually be named in the format of Legend.raw.gz with some variations. 3. Open Microsoft Internet Explorer. 4. Type your dome’s IP address into the address box in the form of http://XXX.XXX.XXX.XXX/update.htm. 5. Press Enter or click Go. 6.
67 After you have clicked Send File, the reload/update can continue processing in one of two ways: • • In most cases, a notice will appear on the monitor screen saying that the update is in progress, while another message appears on the computer screen in Internet Explorer saying that the update is proceeding successfully. In some cases, the camera may not have enough memory to process the reload/update files. In which case, a camera memory low message is displayed.
68 Legend User Manual Appendix. System defaults Default title positions Figure 58 shows you all of the titles that you can turn on to appear on the monitor screen. Figure 58. Default title positions Default programming settings Table 4 lists the system’s programming defaults. Table 4.
69 Table 4. Default programming settings Setting Default Day/Night Automatic Digital zoom limit 12x Electronic image flip (E-flip) On Exposure control Iris Gain 0 Language English Lift 0 Night mode Off IP address 192.168.208.
70 Legend User Manual Table 4.
71 Index A action.......................................................................................................46 actions menu ...........................................................................................29 admin passcode .......................................................................................12 advanced programming...........................................................................10 alarms........................................................................
72 Legend DRAFT User Manual L lift............................................................................................................27 logs screen...............................................................................................61 M program areas ...................................................................................................45 presets.........................................................................................7, 8, 32 privacy masks .................
73 system menu ...........................................................................................59 troubleshooting .......................................................................................65 system operation .....................................................................................63 T U updating the software..............................................................................65 technical support ..............................................................
