Advanced Planning Guide

monogram.com
53
Chimney hoods
Professional hoodsCustom hood insertsTelescopic
downdraft vents
Advance planning for chimney hoods—island
This vent hood must be installed 24" minimum to 30" maximum
above the cooking surface; 25-1/2" is recommended to
ensure
that the duct cover meets the ceiling. The cooking
surface
should be at least 36" above the floor.
A mounting template is provided with the installation
instructions to help position the hood above the cooking
surface and to locate the mounting brackets.
Charcoal filter replacements are available from your dealer or
by calling 800.626.2002. Order catalog number WB02X10731.
Product dimensions and clearances
This stainless steel hood can be installed over any Monogram
®
cooktop except Professional models. Accessories to meet
correct ceiling heights are required.
Model ZV850/855SPSS
* 50-1/8" for 10' ceiling using
ZX8510SPSS accessory
605Dia150
*Height
to Ceiling
8-1/4"
35-3/8" (excluding utensil rods)
36-1/2" (including utensil rods)
27-1/2"
24" to 30"
36" Min.
Using duct cover accessories
A duct cover accessory is required for all ceiling heights.
Use this chart to determine the correct duct cover accessory
for 8' to 10' ceilings that must be ordered with the hood.
15-3/4"
9-7/16"
20-3/4"
20-3/4"
The serial plate is located behind the removable filters.
ZV850/ZV855 installation heights
Ceiling
height
Possible vented
installation
height*
Possible
recirculating
installation
height
Lower frame 20-3/4" Lower frame 20-3/4" Lower duct 18" Upper duct 18" Upper frame 31" Supplied lower frame Lower duct 26-1/4" Upper duct 26-1/4"
7' 11" 24" 24"
Supplied frame
Supplied duct covers
8' 0" 24" to 25" 24" to 25"
8' 1" 24" to 26" 24" to 26"
8' 2" 24" to 27" 24" to 27"
8' 3" 24" to 28" 24" to 28"
8' 4" 27" to 29" 24" to 29"
8' 5" 28" to 30" 24" to 30"
8' 6" 29" to 30" 25" to 30"
8' 7" 30" 26" to 30"
8' 8" 27" to 30"
8' 9" 28" to 30"
ZX8510SPSS – accessory upper frame
8' 10" 29" to 30"
8' 11" 30"
8' 7" 24" 24"
ZX8510SPSS – accessory duct covers
8' 8" 24" to 25" 24" to 25"
8' 9" 24" to 26" 24" to 26"
8' 10" 24" to 27" 24" to 27"
8' 11" 24" to 28" 24" to 28"
9' 0" 24" to 29" 24" to 29"
9' 1" 24" to 30" 24" to 30"
9' 2" 24" to 30" 24" to 30"
9' 3" 24" to 30" 24" to 30"
9' 4" 24" to 30" 24" to 30"
9' 5" 24" to 30" 24" to 30"
9' 6" 24" to 30" 24" to 30"
9' 7" 24" to 30" 24" to 30"
9' 8" 25" to 30" 24" to 30"
9' 9" 26" to 30" 24" to 30"
9' 10" 27" to 30" 25" to 30"
9' 11" 28" to 30" 25" to 30"
10' 0" 29" to 30" 26" to 30"
10' 1" 30" 27" to 30"
10' 2" 28" to 30"
10' 3" 29" to 30"
10' 4" 30"
*Based on 36" countertop height.
Duct Cover Dimensions
ZX8510SPSS Duct Cover
Accessory
This accessory is available for
installation with ceiling heights
above 8'7" to 10' and higher.
This accessory consists of two
26-1/4" duct covers and a 31"
upper support frame piece.
Supplied
duct cover