User's Manual
Table Of Contents
- Slide Number 1
- Document Control
- Transport
- Storage
- Unpacking of Equipment
- Installation
- Slide Number 7
- Specialty Tools Required / Adhesives
- Specialty Tools Required / Adhesives
- Specialty Tools Required / Adhesives
- In Vehicle Unit (IVU) (PROD0842)
- Input Power & Signal Connections
- Input Power & Signal Connections
- IVU Mounting
- Mounting Locations & Cable Runs
- Mounting Locations & Cable Runs
- Light Vehicle
- Light Vehicle
- Haul Truck
- Haul Truck
- Slide Number 21
- Slide Number 22
- Slide Number 23
- Slide Number 24
- Heavy vehicle (excluding Haul Truck)
- Heavy vehicle (excluding Haul Truck)
- Display Unit (PROD0839)
- Display Unit (PROD0839)
- Display Unit (PROD0839)
- Display Unit (PROD0839)
- Display Unit (PROD0839)
- RF Installations
- RF Installations
- Upgrades
- Interconnections – 4CAM/4RF
- Interconnections – 4CAM/4RF
- Interconnections – 1CAM/1RF
- Interconnections – 1CAM/1RF
- Interconnections - LV
- Interconnections - LV
- Input Power & Signal Connections
- Slide Number 42
- Slide Number 43
- Deutsch Connector
- Input Power & Signal Connections
- Input Power & Signal Connections
- General Wiring Principles
- Antenna cable terminations
- Antenna cable terminations
- Antenna cable terminations
- Antenna cable terminations
- Antenna cable terminations
- Antenna cable terminations
- Testing Antenna cable terminations
- Testing Antenna cable terminations
- Antenna Cable Connection Security
- Configuration
- Configuration – Installation Measurements
- Configuration – Installation Measurements
- Configuration – Installation Measurements
- IVU Orientation
- IVU Orientation (Examples)
- Configuration
- Configuration
- Shovel with Heading
- Shovel with Heading Overview
- Primary IVU Configuration
- Primary IVU Configuration
- Secondary IVU Installation
- Secondary IVU Wiring
- Secondary IVU Configuration
- Shovel Heading Testing
- Shovel Heading Testing
- Configuration & Install Record
- Configuration & Install Record
- Configuration & Install Record
- Record Keeping
- Trouble Shooting
- Trouble Shooting
- Trouble Shooting
- Service and Maintenance
- Service and Maintenance
- Decommission
- Disposal
- Disclaimer
- Disclaimer
- Contact Details
- Slide Number 88
6
CAS GPS Installation Manual Rev G1
2/17/2016
Installation
Installation should be in accordance with the installation procedures defined by GE
Mining and only performed by authorised and qualified installers.
This device has been designed to operate with the antennas listed below, and having
a maximum gain listed. Antennas not included in this list or having a gain greater
than those listed are strictly prohibited for use with this device. The required antenna
impedance is 50ohms.
GE
Part#
Relevant Product
(x = any variant)
CAS-GPS Port Nominal
Impedance
Gain Operating
Frequency
PROD0852 PROD084x-2 V2V 50 Ω +4dBi 902-928MHz
PROD0874 PROD084x-1 V2V 50 Ω +4dBi 821-896MHz
PROD0853 PROD084x-x GPS (Receive Only) 50 Ω +26dBi 1574.42-1576.42MHz
PROD0854 PROD0843-x, PROD0847-x GSM / 3G 50 Ω 0dBi
+1.7dBi
+2.9dBi
698-960MHz
1710-1990MHz
2100-2700MHz
PROD0833 PROD0842-x, PROD0847-x Wi - Fi 50 Ω <+5.0dBi 2400-2484MHz