Operator's Manual Part 1
Table Of Contents
- Contents
- 1 The Basics 1-1
- 2 Safety 2-1
- 3 Equipment Overview 3-1
- Introduction 3-3
- ApexPro Telemetry System 3-4
- Compatibility with Bedside Monitors 3-5
- ApexPro Transmitters 3-6
- ApexPro CH Transmitter (not for sale outside of the U.S. and Canada) 3-10
- ApexPro FH Transceiver (not for sale outside of the U.S.) 3-11
- Apex Oximeter SpO2 Module 3-12
- Xpod™ Oximeter 3-13
- Accutracker DX Noninvasive Blood Pressure (NBP) Monitor 3-14
- DINAMAP® PRO Series Monitors 3-16
- Antenna System 3-17
- Receiver System 3-17
- Unity Network 3-17
- CIC Pro Clinical Information Center 3-18
- 4 Connection 4-1
- 5 Maintenance 5-1
- 6 Telemetry Setup 6-1
- 7 Admit/View a Patient 7-1
- 8 Alarm Control 8-1
- 9 Printing 9-1
- 10 Patient Data 10-1
- 11 ECG Monitoring 11-1
- 12 SpO2 Monitoring 12-1
- 13 NBP Monitoring 13-1
- Introduction 13-3
- Safety Considerations 13-4
- Programming the Blood Pressure Monitor 13-5
- Patient Preparation 13-9
- NBP Monitoring 13-13
- Pressures Tab Sheet 13-15
- Troubleshooting 13-17
- Message Glossary A-3
- Contact Information B-3
- Abbreviations and Symbols C-3
- The Basics D-3
- Safety D-5
- Equipment Overview D-8
- Connections D-14
- Maintenance D-18
- Compliance D-26
- 1 The Basics
- 2 Safety
- 3 Equipment Overview
- Introduction
- ApexPro Telemetry System
- Compatibility with Bedside Monitors
- ApexPro Transmitters
- ApexPro CH Transmitter (not for sale outside of the U.S. and Canada)
- ApexPro FH Transceiver (not for sale outside of the U.S.)
- Apex Oximeter SpO2 Module
- Xpod™ Oximeter
- Accutracker DX Noninvasive Blood Pressure (NBP) Monitor
- DINAMAP® PRO Series Monitors
- Antenna System
- Receiver System
- Unity Network
- CIC Pro Clinical Information Center
- 4 Connection
- 5 Maintenance
- 6 Telemetry Setup
- 7 Admit/View a Patient
3-6 ApexPro Telemetry System Revision D
2001989-134
Equipment Overview: ApexPro Telemetry System
ApexPro Transmitters
The ApexPro transmitter sends the patient’s ECG data to the ApexPro
receiver subsystem for processing. Data is then transmitted via a
dedicated Ethernet interface to the CIC Pro for further processing and
viewing.
The ApexPro transmitter can send the patient’s SpO2 data when the
optional Apex Oximeter is connected to it. Additionally, the ApexPro
transmitter can send the patient’s SpO2 and noninvasive blood pressure
data when the optional Xpod Oximeter and/or Accutracker DX
noninvasive blood pressure monitor are connected to it.
The DINAMAP PRO 100–400 series monitors can also be connected to
the ApexPro transmitter. It monitors SpO2, NBP, and temperature.
Configurations
Your transmitters can have one of the following configurations.
1
Single Lead ECGs may be acquired using a 3-, 5-, or 6-lead Multi-Link
leadwire set. However, only a Single Lead ECG is transmitted or
processed.
2
Interface connector ports are active for service use only.
3
Interface connector ports are for connecting serial interface devices.
4
This is a purchased option.
Transmitter Configuration Transmitter Identification
Single Lead ECG
1
INACTIVE interface connector ports
2
Single Lead label.
Blue colored interface connector port dust
cover and the inactive interface connector
ports label.
Single Lead ECG
1
ACTIVE interface connector ports
3, 4
Single Lead label.
Gray colored interface connector port dust
covers.
Multi-Lead ECG
4
ACTIVE interface connector ports
3, 4
No Single Lead label.
Gray colored interface connector port dust
covers.