User's Manual
Table Of Contents
- 1.0 INTRODUCTION
- 2.0 MODEL NUMBER CODES
- 3.0 HARDWARE INSTALLATION AND BASIC INTERFACE REQUIREMENTS
- 4.0 INITIAL STARTUP AND CONFIGURATION
- 4.1 Introduction
- 4.2 STEP 1—Power up the LEDR Radios
- 4.3 STEP 2—Establish Communications with the Radio
- 4.4 STEP 3—Make Initial Login to Radio
- 4.5 STEP 4—Change the SUPER Password
- 4.6 STEP 5—Review Essential Operating Parameters
- 4.7 STEP 6—Set TCP/IP Settings to Enable SNMP and/or Telnet Management (if required)
- 4.8 STEP 7—Set User Configurable Fields
- 4.9 STEP 8—Verify Radio Performance
- 4.10 STEP 9—Install the Link
- 4.11 STEP 10—Verify the Link Performance
- 5.0 CONFIGURATION AND CONTROL VIA THE FRONT PANEL
- 6.0 CONFIGURATIONAND CONTROL VIA THE CONSOLE PORT
- 7.0 STANDARDIZING RADIO CONFIGURATIONS
- 8.0 UPGRADING LEDR FIRMWARE
- 9.0 USING ORDERWIRE
- 10.0 USING THE SERVICE CHANNEL
- 11.0 PROTECTED CONFIGURATION
- 12.0 SPACE DIVERSITY OPERATION
- 13.0 SPARE PARTS, UNITS AND ACCESSORIES
- 14.0 Fractional-T1 INTERFACE CARD 03-3846A01 Fractional-E1 INTERFACE CARD 03-3846A02
- 15.0 INCREASE BANDWIDTH BY CHANGING TRANSMITTER AND RECEIVER FILTERS
- 16.0 BENCH TESTING OF RADIOS
- 17.0 TECHNICAL REFERENCE
- 17.1 Specifications— Models: LEDR 400S, 700S, 900S and1400S
- 17.2 Specifications— Models: LEDR 400F, 900F, 1400F
- 17.3 Specifications— Protected Switch Chassis
- 17.4 Optional Equipment (Consult factory for detailed information)
- 17.5 Accessories
- 17.6 I/O Connector Pinout Information
- 17.7 Watts-dBm-Volts Conversion
- 18.0 RADIO EVENT CODES
- 19.0 IN CASE OF DIFFICULTY
86 LEDR Series I/O Guide MDS 05-3627A01, Rev. D
This command is used to display continuously updated readings of:
RSSI, radio temperature, RF output, signal-to-noise ratio, and FEC
errors (corrected and uncorrectable). The display can be stopped by
pressing Control-C on the terminal.
If the
trend command is used by itself or with all (trend all), all associated
parameters will be reported. More than one argument can be used to dis-
play several selected items in the desired order.
NOTE: This command is not available from a Telnet session.
txkey Radio Transmitter Keying Status
Usage:
txkey [on|off]
This command sets or displays the radio transmitter status. ON indicates
the radio transmitter is keyed and transmitting.
OFF indicates the trans-
mitter is not keyed.
unitid Unit Identification Number for Orderwire and NMS
Usage:
unitid [<ID>]
This command sets or displays the radio’s unit identification number.
This number is used for Orderwire signaling and by the NMS (Network
Management System). (See “USING ORDERWIRE” on Page 99.) The
factory default is the last three numbers of the unit serial number.
(1-999)
uptime Up Time
Usage:
uptime
This command displays how long the radio has been powered-on.
user User Account Information
Usage:
user [subcommand] [<argument>]
Subcommands: add <user> <pass> <perm>
del <user>
perm <user> <perm>
pass
This command provides administrator access for setting new user
accounts and permission levels.
NOTE: The password (pass) and user names are case sensitive and
may not exceed eight characters. Two quotation mark charac-
ters ("") may be used as a “blank” password. If quotation
marks are used, the shift key or cap lock keys must be
depressed.