User's Manual
Table Of Contents
- 1.0 INTRODUCTION
- 2.0 MODEL NUMBER CODES
- 3.0 HARDWARE INSTALLATION AND BASIC INTERFACE REQUIREMENTS
- 4.0 INITIAL STARTUP AND CONFIGURATION
- 4.1 Introduction
- 4.2 STEP 1—Power up the LEDR Radios
- 4.3 STEP 2—Establish Communications with the Radio
- 4.4 STEP 3—Make Initial Login to Radio
- 4.5 STEP 4—Change the SUPER Password
- 4.6 STEP 5—Review Essential Operating Parameters
- 4.7 STEP 6—Set TCP/IP Settings to Enable SNMP and/or Telnet Management (if required)
- 4.8 STEP 7—Set User Configurable Fields
- 4.9 STEP 8—Verify Radio Performance
- 4.10 STEP 9—Install the Link
- 4.11 STEP 10—Verify the Link Performance
- 5.0 CONFIGURATION AND CONTROL VIA THE FRONT PANEL
- 6.0 CONFIGURATIONAND CONTROL VIA THE CONSOLE PORT
- 7.0 STANDARDIZING RADIO CONFIGURATIONS
- 8.0 UPGRADING LEDR FIRMWARE
- 9.0 USING ORDERWIRE
- 10.0 USING THE SERVICE CHANNEL
- 11.0 PROTECTED CONFIGURATION
- 12.0 SPACE DIVERSITY OPERATION
- 13.0 SPARE PARTS, UNITS AND ACCESSORIES
- 14.0 Fractional-T1 INTERFACE CARD 03-3846A01 Fractional-E1 INTERFACE CARD 03-3846A02
- 15.0 INCREASE BANDWIDTH BY CHANGING TRANSMITTER AND RECEIVER FILTERS
- 16.0 BENCH TESTING OF RADIOS
- 17.0 TECHNICAL REFERENCE
- 17.1 Specifications— Models: LEDR 400S, 700S, 900S and1400S
- 17.2 Specifications— Models: LEDR 400F, 900F, 1400F
- 17.3 Specifications— Protected Switch Chassis
- 17.4 Optional Equipment (Consult factory for detailed information)
- 17.5 Accessories
- 17.6 I/O Connector Pinout Information
- 17.7 Watts-dBm-Volts Conversion
- 18.0 RADIO EVENT CODES
- 19.0 IN CASE OF DIFFICULTY
MDS 05-3627A01, Rev. D LEDR Series I/O Guide 73
This command is used to change the password for the user currently
logged in. A maximum of 8 characters is allowed, and it is case sensi-
tive.
ping Ping IP Address (Send ICMP Echo Request)
Usage:
ping [ip address] [reps]
This command is used to verify the accessibility of any IP address on the
network to determine availability and measure network response time.
This command requires proper IP Routing and IP connectivity.
ipaddress—IP address to which you will send the request
reps - Number of requests-to-send (default = 1, maximum = 1000)
Example:
LEDR> ping 10.2.233.12 5
Example Response:
PING 10.2.233.12: 56 data bytes
64 bytes from 10.2.233.12: seq=1, ttl=255, rtt=49ms
64 bytes from 10.2.233.12: seq=2, ttl=255, rtt=6ms
64 bytes from 10.2.233.12: seq=3, ttl=255, rtt=9ms
64 bytes from 10.2.233.12: seq=4, ttl=255, rtt=33ms
64 bytes from 10.2.233.12: seq=5, ttl=255, rtt=12ms
pll Phase Locked Loop
Displays current TX & RX frequencies, and TX/RX PLL status.
Example Response:
pll:
Tx Freq = 438075000 Hz, Rx Freq = 428075000
Tx PLL Status: Locked
Rx PLL Status: Locked
pmmode Power Measurement Mode
Usage:
pmmode <on|off>
This command is used to generate an unmodulated carrier on the trans-
mitter frequency for the purpose of measuring RF output power or fre-
quency stability using a spectrum analyzer.
Example Response:
pmmode: off
NOTE: Enabling the power measurement mode (pmmode on) will take
the local link down (out-of-service).