User's Manual
Table Of Contents
- 1.0 INTRODUCTION
- 2.0 MODEL NUMBER CODES
- 3.0 HARDWARE INSTALLATION AND BASIC INTERFACE REQUIREMENTS
- 4.0 INITIAL STARTUP AND CONFIGURATION
- 4.1 Introduction
- 4.2 STEP 1—Power up the LEDR Radios
- 4.3 STEP 2—Establish Communications with the Radio
- 4.4 STEP 3—Make Initial Login to Radio
- 4.5 STEP 4—Change the SUPER Password
- 4.6 STEP 5—Review Essential Operating Parameters
- 4.7 STEP 6—Set TCP/IP Settings to Enable SNMP and/or Telnet Management (if required)
- 4.8 STEP 7—Set User Configurable Fields
- 4.9 STEP 8—Verify Radio Performance
- 4.10 STEP 9—Install the Link
- 4.11 STEP 10—Verify the Link Performance
- 5.0 CONFIGURATION AND CONTROL VIA THE FRONT PANEL
- 6.0 CONFIGURATIONAND CONTROL VIA THE CONSOLE PORT
- 7.0 STANDARDIZING RADIO CONFIGURATIONS
- 8.0 UPGRADING LEDR FIRMWARE
- 9.0 USING ORDERWIRE
- 10.0 USING THE SERVICE CHANNEL
- 11.0 PROTECTED CONFIGURATION
- 12.0 SPACE DIVERSITY OPERATION
- 13.0 SPARE PARTS, UNITS AND ACCESSORIES
- 14.0 Fractional-T1 INTERFACE CARD 03-3846A01 Fractional-E1 INTERFACE CARD 03-3846A02
- 15.0 INCREASE BANDWIDTH BY CHANGING TRANSMITTER AND RECEIVER FILTERS
- 16.0 BENCH TESTING OF RADIOS
- 17.0 TECHNICAL REFERENCE
- 17.1 Specifications— Models: LEDR 400S, 700S, 900S and1400S
- 17.2 Specifications— Models: LEDR 400F, 900F, 1400F
- 17.3 Specifications— Protected Switch Chassis
- 17.4 Optional Equipment (Consult factory for detailed information)
- 17.5 Accessories
- 17.6 I/O Connector Pinout Information
- 17.7 Watts-dBm-Volts Conversion
- 18.0 RADIO EVENT CODES
- 19.0 IN CASE OF DIFFICULTY
MDS 05-3627A01, Rev. D LEDR Series I/O Guide 67
NOTE: FE1/FT1 always use Span A.
Figure 16 shows the example pictorially. There are no restrictions of
which lines are mapped to which data channel spans.
Invisible place holder
Figure 16. Example of Linemapping
NOTE: The cluster of four RJ-45 jacks on the rear of the radio is coded
from left to right as 1, 2, 3 and 4 as viewed from the outside of the
chassis.
linename Line Name
Usage: linename <linelist> <namelist>
This command is used to set or display meaningful names of up to 16
characters to the four possible line interfaces.The
[linelist] variable rep-
resents a list of line interfaces. It can consist of a single line number or
line name, a comma separated list of line numbers or line names, a range
of line numbers (i.e., 1–4) or, if linelist is not given, all lines. See
Table 19 on Page 59 for a list of line numbers.
The namelist variable consists of a list of names. It can consist of a
single name or a comma/whitespace-separated list of names. Names can
be up to 16 characters long.
linerr Line Errors
Usage:
linerr [linelist] [on|off]
This command measures and displays the line performance between the
radio and customer equipment. Entering the command
linerr on will ini-
tialize the line error measurement feature. The
[linelist] variable repre-
sents a list of line interfaces. It can consist of a single line number or line
name, a comma-separated list of line numbers or line names, a range of
line numbers (i.e., 1–4), or if linelist is not given all lines will be dis-
played. See Table 19 on Page 59 for a list of line numbers.
log Log of Events
3
4
2
1
Span A
Span B
Span C
Span D
LEDR LINE
E1/T1 SPAN(RJ-45 JACK)
E1
FT1
FE1
E1
FT1
FE1