User's Manual
Table Of Contents
- 1.0 INTRODUCTION
- 2.0 MODEL NUMBER CODES
- 3.0 HARDWARE INSTALLATION AND BASIC INTERFACE REQUIREMENTS
- 4.0 INITIAL STARTUP AND CONFIGURATION
- 4.1 Introduction
- 4.2 STEP 1—Power up the LEDR Radios
- 4.3 STEP 2—Establish Communications with the Radio
- 4.4 STEP 3—Make Initial Login to Radio
- 4.5 STEP 4—Change the SUPER Password
- 4.6 STEP 5—Review Essential Operating Parameters
- 4.7 STEP 6—Set TCP/IP Settings to Enable SNMP and/or Telnet Management (if required)
- 4.8 STEP 7—Set User Configurable Fields
- 4.9 STEP 8—Verify Radio Performance
- 4.10 STEP 9—Install the Link
- 4.11 STEP 10—Verify the Link Performance
- 5.0 CONFIGURATION AND CONTROL VIA THE FRONT PANEL
- 6.0 CONFIGURATIONAND CONTROL VIA THE CONSOLE PORT
- 7.0 STANDARDIZING RADIO CONFIGURATIONS
- 8.0 UPGRADING LEDR FIRMWARE
- 9.0 USING ORDERWIRE
- 10.0 USING THE SERVICE CHANNEL
- 11.0 PROTECTED CONFIGURATION
- 12.0 SPACE DIVERSITY OPERATION
- 13.0 SPARE PARTS, UNITS AND ACCESSORIES
- 14.0 Fractional-T1 INTERFACE CARD 03-3846A01 Fractional-E1 INTERFACE CARD 03-3846A02
- 15.0 INCREASE BANDWIDTH BY CHANGING TRANSMITTER AND RECEIVER FILTERS
- 16.0 BENCH TESTING OF RADIOS
- 17.0 TECHNICAL REFERENCE
- 17.1 Specifications— Models: LEDR 400S, 700S, 900S and1400S
- 17.2 Specifications— Models: LEDR 400F, 900F, 1400F
- 17.3 Specifications— Protected Switch Chassis
- 17.4 Optional Equipment (Consult factory for detailed information)
- 17.5 Accessories
- 17.6 I/O Connector Pinout Information
- 17.7 Watts-dBm-Volts Conversion
- 18.0 RADIO EVENT CODES
- 19.0 IN CASE OF DIFFICULTY
MDS 05-3627A01, Rev. D LEDR Series I/O Guide v
EIA-530-A Data—Rear Panel ......................................................................................................128
G.703 Data Connectors (4)—Rear Panel ....................................................................................128
Service Channel—Rear Panel.....................................................................................................129
Alarm—Rear Panel......................................................................................................................129
17.7 Watts-dBm-Volts Conversion ...................................................................................................129
18.0 RADIO EVENT CODES..................................................................................................130
19.0 IN CASE OF DIFFICULTY ..............................................................................................138
19.1 FACTORY TECHNICAL ASSISTANCE ...................................................................................138
19.2 FACTORY REPAIRS ................................................................................................................139
To Our Customers
We appreciate your patronage. You are our business. We promise to serve and anticipate your needs. We will strive to
give you solutions that are cost effective, innovative, reliable and of the highest quality possible. We promise to build
a relationship that is forthright and ethical, one that builds confidence and trust.
Copyright Notice
This document and all software described herein are protected by copyright. Copyright 2003, Microwave Data Sys-
tems Inc. All rights reserved. Trademarks held by other companies used in this publication are acknowledged to be
property of the holder.
Antenna Installation Warning
1. All antenna installation and servicing is to be performed by qualified technical personnel only. When servicing
the antenna, or working at distances closer than those listed in the tables below, ensure the transmitter has been
disabled.
2.
Typically, the antenna connected to the transmitter is a directional (high gain) antenna, fixed-mounted on the
side or top of a building, or on a tower. Depending upon the application and the gain of the antenna, the total com-
posite power could exceed 20 to 50 watts EIRP. The antenna location should be such that only qualified technical
personnel can access it, and that under normal operating conditions no other person can touch the antenna or
approach within 4.34 meters of the antenna. This is a worst case scenario derived from maximum permissible exposure evaluation
Exposure
RF
for General Population/Uncontrolled Exposure using maximum permitted antenna gain (30 dBi) for LEDR Series