User's Manual
Table Of Contents
- 1.0 INTRODUCTION
- 2.0 MODEL NUMBER CODES
- 3.0 HARDWARE INSTALLATION AND BASIC INTERFACE REQUIREMENTS
- 4.0 INITIAL STARTUP AND CONFIGURATION
- 4.1 Introduction
- 4.2 STEP 1—Power up the LEDR Radios
- 4.3 STEP 2—Establish Communications with the Radio
- 4.4 STEP 3—Make Initial Login to Radio
- 4.5 STEP 4—Change the SUPER Password
- 4.6 STEP 5—Review Essential Operating Parameters
- 4.7 STEP 6—Set TCP/IP Settings to Enable SNMP and/or Telnet Management (if required)
- 4.8 STEP 7—Set User Configurable Fields
- 4.9 STEP 8—Verify Radio Performance
- 4.10 STEP 9—Install the Link
- 4.11 STEP 10—Verify the Link Performance
- 5.0 CONFIGURATION AND CONTROL VIA THE FRONT PANEL
- 6.0 CONFIGURATIONAND CONTROL VIA THE CONSOLE PORT
- 7.0 STANDARDIZING RADIO CONFIGURATIONS
- 8.0 UPGRADING LEDR FIRMWARE
- 9.0 USING ORDERWIRE
- 10.0 USING THE SERVICE CHANNEL
- 11.0 PROTECTED CONFIGURATION
- 12.0 SPACE DIVERSITY OPERATION
- 13.0 SPARE PARTS, UNITS AND ACCESSORIES
- 14.0 Fractional-T1 INTERFACE CARD 03-3846A01 Fractional-E1 INTERFACE CARD 03-3846A02
- 15.0 INCREASE BANDWIDTH BY CHANGING TRANSMITTER AND RECEIVER FILTERS
- 16.0 BENCH TESTING OF RADIOS
- 17.0 TECHNICAL REFERENCE
- 17.1 Specifications— Models: LEDR 400S, 700S, 900S and1400S
- 17.2 Specifications— Models: LEDR 400F, 900F, 1400F
- 17.3 Specifications— Protected Switch Chassis
- 17.4 Optional Equipment (Consult factory for detailed information)
- 17.5 Accessories
- 17.6 I/O Connector Pinout Information
- 17.7 Watts-dBm-Volts Conversion
- 18.0 RADIO EVENT CODES
- 19.0 IN CASE OF DIFFICULTY
46 LEDR Series I/O Guide MDS 05-3627A01, Rev. D
icopy Firmware image copy
Page 61
idlepat Set/display timeslot idle pattern
Page 61
info Set/display radio/owner information
Page 62
interface Set/display the payload data interface
Page 62
interleave Set/display interleave depth
Page 63
ip Set/display the radio’s IP configuration
Page 63
iverify Firmware image verify
Page 64
lcd Tests radio’s front panel LCD display
Page 64
led Tests radio’s front panel LEDs
Page 64
line Set/display pulse shape settings
Page 65
linecode Set/display the linecode used by span(s)
Page 66
linerr Show/enable/clear line errors
Page 67
linemap Set/display current linemapping configuration
Page 66
linename Set/display names for line interfaces
Page 67
log View, sort, clear, send event log information
Page 67
login Console user level access
Page 68
logout Console user exit
Page 69
loopback Set/display loopback modes
Page 69
model Display radio model number
Page 71
modem Set/display radio modulation type and data rate
Page 71
network Display radios in the network
Page 72
passwd Sets new user password (8 characters max.)
Page 72
ping Test link to IP address on network
Page 73
pll Displays Phase Lock Loop status
Page 73
pmmode Enables/disables modem modulator power
measurement mode (on/off)
Page 73
rdnt Set/display redundant operating configuration
Page 74
reframe Set/display the reframe criteria
Page 75
reprogram Reprograms radio software
Page 76
rfocal Set/display RF power output calibration sequence
Page 76
rfout Displays transmit power
Page 77
rlogin Log in to remote radio
Page 77
route Add/delete/modify IP routing table entries
Page 77
Table 15. NMS Commands (Continued)
Command Description Summary Details