User's Manual
Table Of Contents
- 1.0 INTRODUCTION
- 2.0 MODEL NUMBER CODES
- 3.0 HARDWARE INSTALLATION AND BASIC INTERFACE REQUIREMENTS
- 4.0 INITIAL STARTUP AND CONFIGURATION
- 4.1 Introduction
- 4.2 STEP 1—Power up the LEDR Radios
- 4.3 STEP 2—Establish Communications with the Radio
- 4.4 STEP 3—Make Initial Login to Radio
- 4.5 STEP 4—Change the SUPER Password
- 4.6 STEP 5—Review Essential Operating Parameters
- 4.7 STEP 6—Set TCP/IP Settings to Enable SNMP and/or Telnet Management (if required)
- 4.8 STEP 7—Set User Configurable Fields
- 4.9 STEP 8—Verify Radio Performance
- 4.10 STEP 9—Install the Link
- 4.11 STEP 10—Verify the Link Performance
- 5.0 CONFIGURATION AND CONTROL VIA THE FRONT PANEL
- 6.0 CONFIGURATIONAND CONTROL VIA THE CONSOLE PORT
- 7.0 STANDARDIZING RADIO CONFIGURATIONS
- 8.0 UPGRADING LEDR FIRMWARE
- 9.0 USING ORDERWIRE
- 10.0 USING THE SERVICE CHANNEL
- 11.0 PROTECTED CONFIGURATION
- 12.0 SPACE DIVERSITY OPERATION
- 13.0 SPARE PARTS, UNITS AND ACCESSORIES
- 14.0 Fractional-T1 INTERFACE CARD 03-3846A01 Fractional-E1 INTERFACE CARD 03-3846A02
- 15.0 INCREASE BANDWIDTH BY CHANGING TRANSMITTER AND RECEIVER FILTERS
- 16.0 BENCH TESTING OF RADIOS
- 17.0 TECHNICAL REFERENCE
- 17.1 Specifications— Models: LEDR 400S, 700S, 900S and1400S
- 17.2 Specifications— Models: LEDR 400F, 900F, 1400F
- 17.3 Specifications— Protected Switch Chassis
- 17.4 Optional Equipment (Consult factory for detailed information)
- 17.5 Accessories
- 17.6 I/O Connector Pinout Information
- 17.7 Watts-dBm-Volts Conversion
- 18.0 RADIO EVENT CODES
- 19.0 IN CASE OF DIFFICULTY
44 LEDR Series I/O Guide MDS 05-3627A01, Rev. D
6.2 Initial Connection to the CONSOLE Port
NOTE: The default connection parameters for console operation are
9600 bps, 8 bits, no parity, 1 stop bit (96008N1). The console
port is configured as DCE.
1. Connect a terminal to the front panel DB-9 connector labeled .
2. Open an ANSI terminal application on the terminal. (If using the
Windows operating system, a HyperTerminal session can be started
by selecting
Programs>>Accessories>>HyperTerminal.)
3. Press a few times. When communications are established
with the radio, a
LEDR> text prompt appears on the terminal screen.
4. Type
login <your username> (or rlogin <your username> for remote
access) and press . At the password> prompt, type your pass-
word (Eight characters maximum; case sensitive).
5. You now have access to the command line interface. It can be used
to configure and query the radio parameters and setup information.
The available commands can be listed on the display by typing
help
at the
LEDR> prompt, then .
6.3 NMS Commands
Once you are successfully logged in, the Network Management System
(NMS) commands shown in Table 15 are available at the command line
prompt (
LEDR>). Note that some commands are model and/or feature
specific. See Table 16 on Page 48 for an explanation of feature-specific
icons.
Command Entry Hints—Recalling Commands
Recalling the most
recent command
To recall the most recent command issued from the terminal, enter two
exclamation points (
!!) followed by . The command will reap-
pear at the
LEDR> prompt. Press again to invoke the command,
or edit the string as necessary.
Recalling the most
recent command
beginning with xyz...
To recall the most recent command beginning with xyz (where xyz is a
string of up to 16 characters), enter an exclamation point (
!) followed by
a few characters of the command. For example, if the
threshold com-
mand was recently used, entering !thresh followed by would
make the
threshold command reappear at the LEDR> prompt. Press
again to invoke the command, or edit the string as necessary.
These “recall” techniques are especially useful for commands con-
taining a long string of characters, such as IP addresses or other config-
uration data.
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER