User Guide
Installation Instructions Document No. 466-1574.
4
Introduction
This ITI Securit
y
S
y
stem is eas
y
to install if
y
ou
p
lan
ahead and
p
erform the installation in the followin
g
or-
der.
1. Plan where to locate the hardwire sirens, sensors
and Control Panel. Use the tear out
p
lannin
g
sheets at back of this manual.
2. Wire the Class II transformer, hardwire sirens,
and
p
hone.
3. Decide how the sensors, li
g
hts, and s
y
stem
o
p
tions will o
p
erate.
4. Pro
g
ram the sensors, li
g
hts and a
pp
liances, and
s
y
stem o
p
tions.
5. Install sensors and Li
g
htin
g
Modules.
6. Test s
y
stem.
Note
: Program the sensors before installing them because
the Control Panel and sensors must be in the same place
for programming. After you’ve programmed each sensor,
you can install them where you planned.
System Components
The s
y
stem can monitor u
p
to 24 sensors usin
g
an
y
combination of the followin
g
sensors:
• Door/Window Sensor (60-670-95R)
•Ke
y
Chain Touch
p
ad (60-659-95R)
• Remote Handheld Touch
p
ad (60-671-95R)
• Touchtalk 2-Wa
y
RF Touch
p
ad (60-788-95R)*
• Indoor Motion Sensor (60-639-95R)
• Outdoor Motion Sensor (60-639-95R-OD)
• Carbon Monoxide Alarm (60-652-95)
• Water Sensor (60-744-95R)
• Freeze Sensor (60-742-95R)
• SWS (60-736-95)*
• ITI 319.5 Sensors (includin
g
Smoke Sensors,
excludin
g
other touch
p
ads)
Note
: Both ITI SAW and Crystal sensors function with this
Control Panel.
You ma
y
use an
y
of these modules:
•Interro
g
ator
®
200 Audio Verification Module
(AVM) (60-787)*
• X-10 Lam
p
Modules (13-403)*
• X-10 A
pp
liance Modules (13-402)*
• X-10 Powerhorn/Remote Siren Modules (13-
398)*
• X-10 Universal/Gara
g
e Door Modules (13-399)*
• X-10 Wall Switch Modules (13-397)*
Note
: Use of the above X-10 modules has not been inves-
tigated by UL.
Fi
g
ure 1. shows the Control Panel, control touch
p
ads,
and some com
p
atible sensors and modules.
Figure 1. Typical Security System Components
Security System
The securit
y
s
y
stem has three t
yp
es of com
p
onents:
the Control Panel, devices that re
p
ort to the Control
Panel, and devices that res
p
ond to commands from
the Control Panel.
Control Panel
The Control Panel is the main
p
rocessin
g
unit for all
securit
y
functions. It receives si
g
nals from and re-
s
p
onds to wireless sensors and wireless touch
p
ads
throu
g
hout the
p
remises. The buttons o
p
erate the se-
curit
y
s
y
stem. When usin
g
the Control Panel with the
cover o
p
en, the buttons
p
ro
g
ram the securit
y
s
y
stem.
Two confi
g
urations of the Simon Control Panel are
available. One has an on-board 2-wa
y
voice micro-
p
hone, the other does not. The Interro
g
ator® can be
added to either confi
g
uration.
X-10 POWERHOUSE
1
3
5
9
13
7
11
15
A
C
E
I
M
GK
O
UNIT CODE
HOUSE CODE
CONTINUOUS
MOMENTARY
SOUNDER ONLY
SOUNDER & RELAY
RELAY ONLY
ON
OFF
DOOR/WINDOW
SENSOR
LAMP
MODULE
APPLIANCE
MODULE
GARAGE DOOR
MODULE
REMOTE
HANDHELD
TOUCHPAD
MOTION
SENSOR
KEYCHAIN
TOUCHPAD
SMOKE
SENSOR
8988G21D.DSF
1
3
5
9
13
7
11
15
A
C
E
I
M
GK
O
1
3
5
9
13
7
11
15
A
C
E
I
M
GK
O
7
4
1
89
5
2
6
3
Off
sP
EMERGENCY
On
d&sre s Hol hBtoeKy
DISARM
SYSTEM
STATUS
Doors &
Windows
ARM
ARM
Sensors
Motion
-
CARBON
MONOXIDE
DETECTOR
CARBON MONOXIDE
ALARM
TOUCHTALK
2-WAY RF
TOUCHPAD
AUDIO VERIFICATION
MODULE
* = Not Available with Basic Model