User Guide
Installation Instructions Document No. 466-1574.
32
Materials Needed
•Pencil
• Hammer
• Screwdriver
To mount the panel:
1. Choose a s
p
ot within a few feet of an electrical
outlet (the outlet should not be controlled b
y
a
wall switch) and also within reach of a tele
p
hone
j
ack. The Control Panel can be
p
laced on a desk,
tableto
p
, or it can be wall mounted.
2. O
p
en the Control Panel cover and
p
osition on the
wall.
3. Mark the screw hole locations with a
p
encil.
4. Start holes with the ti
p
of the screwdriver or a
nail.
5. Ta
p
the wall anchors
p
rovided into the holes.
6. Insert the screws and
p
artiall
y
ti
g
hten with the
screwdriver.
7. Han
g
the Control Panel on the screws and ti
g
hten
securel
y
.
8. Remove the center screw from the outlet cover
p
late.
9. Position the transformer so that its screw hole is
ali
g
ned with the screw hole on the outlet cover
p
late. Then
p
lu
g
the transformer into the outlet.
10. Re
p
lace the screw, and use it to secure the trans-
former to the outlet cover
p
late. Ti
g
hten the
screw firml
y
with
y
our screwdriver.
Sensor Installation
Use the installation instructions included with each
sensor or if installin
g
SAW sensors use document
466-1622, Booklet of Installation Instructions, at-
tached to the back of this manual, for SAW Sensors.
Testing the Control Panel
Test the Control Panel b
y
p
ressin
g
the buttons as de-
scribed below:
• ARM Doors & Windows-The Control Panel
arms Doors & Windows. Press twice to eliminate
the
p
re
p
ro
g
rammed entr
y
dela
y
. The button will
blink when No Entr
y
Dela
y
is on.
• ARM Motion Sensors-The Control Panel will
arm Motion Sensors. Press twice to turn Latch-
ke
y
on. The button blinks when Latchke
y
is on.
• DISARM -The Control Panel will disarm Doors,
Windows, and Motion Sensors when also enter-
in
g
the a
pp
ro
p
riate access code.
• SYSTEM STATUS-Press to determine s
y
stem
status and s
y
stem time.
• CHIME Doors-Press to enable two bee
p
s which
will sound from the interior siren out
p
ut, the
p
anel siren, SWS, and the X-10
p
owerhorn siren
(if set to unit number 9) when a
p
rotected door or
window, that is
p
ro
g
rammed as sensor t
yp
e 10 or
13, is o
p
ened.
• CHIME S
p
ecial Motion- Press to enable three
bee
p
s which will sound from the interior siren
out
p
ut, the
p
anel siren, SWS, and the X-10
p
ow-
erhorn siren (if set to unit number 9) when a
Motion Sensor, that is
p
ro
g
rammed as sensor
t
yp
e 25, is activated. If there are no sensors
learned as t
yp
e 25, this function will not be avail-
able. The control
p
anel will also announce which
sensor was tri
pp
ed if chime voice (o
p
tion 41) is
on.
• LIGHTS Time Activated-Press to enable s
y
stem
controlled li
g
hts to turn on/off at a scheduled
time.
• LIGHTS Sensor Activated-Press to enable s
y
s-
tem controlled li
g
hts to turn on for 4 minutes
when a s
p
ecific sensor is tri
pp
ed.
• EMERGENCY-Press and hold or
p
ress twice
q
uickl
y
to activate a non-medical emer
g
enc
y
alarm.
Testing the System
This section describes how to
p
erform the followin
g
test
p
rocedures:
• Testin
g
sensors
• Testin
g
p
hone communication
• Testin
g
central station communications
• Testin
g
the X-10 Lam
p
Modules
You should test the s
y
stem after installin
g
, after ser-
vicin
g
, and after addin
g
or removin
g
devices from the
s
y
stem.