Installation Guide
13
USE LA PLANTILLA DEL
GABINETE SUPERIOR PARA LA
PREPARACIÓN DEL GABINETE
'HEHUiSHUIRUDUDJXMHURVSDUDORVWRUQLOORVGHDSR\R
superiores, un agujero suficientemente grande
SDUDTXHHOFDEOHHOpFWULFRTXHSD\XQUHFRUWHOR
suficientemente grande como para
TXHHODGDSWDGRUGHHVFDSHSXHGDVHULQWURGXFLGR
A2.
/HDODVLQVWUXFFLRQHVVREUHOD3/$17,//$'(/
*$%,1(7(683(5,25
3pJXHORGHEDMRGHOJDELQHWHVXSHULRU
7DODGUHORVDJXMHURVVLJXLHQGRODVLQVWUXFFLRQHV
HQOD3/$17,//$'(/*$%,1(7(683(5,25
PRECAUCIÓN
Use gafas de seguridad
cuando perfore los agujeros en el fondo del
gabinete.
Instrucciones de instalación
CONTROLE LA ORIENTACIÓN DEL
MOTOR DEL CALEFACTOR
/DDEHUWXUDGHODVSDOHWDVGHOYHQWLODGRUGHO
calefactor debe apuntar hacia la parte superior del
KRUQRPLFURRQGDV6LODDEHUWXUDGHOYHQWLODGRU\D
está apuntada hacia la parte superior del horno
PLFURRQGDVYD\DGLUHFWRDO3DVR$'HRWURPRGR
continúe con el Paso A4 para ajustar la orientación
del motor.
ADAPTACIÓN DEL CALEFACTOR
PARA LA VENTILACIÓN EXTERNA
5HWLUH\JXDUGHORVWRUQLOORVTXHVRVWLHQHQHO
motor del calefactor al horno microondas.
Retire y guarde el escudo metálico del calefactor
en la parte superior del microondas, deslizando el
mismo de forma recta.
A3.
A4.
1
2
Parte posterior del
horno microondas
7RUQLOORVGH
Retención del
Calentador
Plato del calefactor
7RUQLOORGH5HWHQFLyQGHO
Calentador
ADAPTACIÓN DEL CALEFACTOR
PARA LA VENTILACIÓN EXTERNA
(Cont.)
Adhiera el escudo metálico del calefactor sobre
la parte trasera del microondas, deslizando el
mismo hacia abajo.
$EUDODSXHUWDGHOFDOHIDFWRUOHYDQWDQGRHOPLVPR
sobre la parte trasera del horno microondas.
Con cuidado, empuje hacia usted la unidad del
FDOHIDFWRU/RVFDEOHVVHH[WHQGHUiQORVXILFLHQWH
como para permitirle ajustar la unidad del
calefactor.
Haga rodar la unidad del calentador 90º, de modo
TXHODVDEHUWXUDVGHODVSDOHWDVGHOYHQWLODGRU
enfrenten la parte superior del horno.
A4.
3
4
5
6
ANTES: Aberturas
de las Paletas del
Ventilador Hacia
Arriba
DESPUÉS: Aberturas
de las Paletas del
Ventilador Hacia
Arriba
Escudo del
Calefactor
Roll
NOTA: Asegúrese
GHTXHORVFDEOHV
permanezcan
dirigidos hacia las
ranuras de la
estructura del
motor.