MFL59060917
Safety Information BEFORE YOU BEGIN CONTENTS Design Information Models Available ......................................................................2 Product Dimensions and Clearances ............................4 Tools and Parts Required ....................................................4 Parts Supplied ...........................................................................4 Advance Planning ...................................................................
Información de seguridad ANTES DE COMENZAR Lea estas instrucciones por completo y con detenimiento. IMPORTANTE ³ Guarde estas instrucciones para el uso de inspectores locales. IMPORTANTE ³ Cumpla con todos los códigos y ordenanzas vigentes. • Nota al instalador ³ Asegúrese de dejar estas instrucciones con el Consumidor. • Nota al consumidor ³ Mantenga estas instrucciones con el Manual del Propietario para referencia futura.
Installation Preparation ELECTRICAL REQUIREMENTS Single Advantium 120 Installation: This product requires a 120-volt, 60 Hz, 15-amp circuit and draws 1.8 kilowatts. This product must be connected to a supply circuit of the proper voltage and frequency. • Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating. • The power supply cord and plug should be brought to a separate 15 or 20 ampere branch circuit single grounded receptacle.
Installation Preparation Preparation WITHOUT an Accessory Storage Drawer PREPARE THE OPENING PREPARE THE OPENING (cont.) The Advantium 120V can be installed in combination with other GE/Monogram appliances. Always follow each product’s Installation Instructions to complete the installation. Installation over a GE/Monogram Warming Drawer: 30s 23-1/2s Single Advantium 120V Installation: Order a 30s wide single oven cabinet or cut the opening in a wall to the dimensions shown.
Installation Preparation Preparation WITHOUT an Accessory Storage Drawer PREPARE THE OPENING (cont.) PREPARE THE OPENING (cont.) Installation over a GE/Monogram oven: Installation over a GE/Monogram Oven and Warming Drawer: 30s 23-1/2s 25-1/4s 17-1/2s 30s Construct Solid Bottom Min. 3/8s Plywood Supported by 2 x 4 or 2 x 2 Runners all Four Sides 23-1/2s 25-1/4s 2s Min. (3s Recommended) 17-1/2s Per Oven Requirement Construct Solid Bottom Min.
Installation Preparation Preparation WITHOUT an Accessory Storage Drawer PREPARE THE OPENING (cont.) PREPARE THE OPENING (cont.) Installation over another GE/Monogram Under-the-Counter (UTC) oven: Installation under a GE/Monogram Microwave Oven and over a Warming Drawer: 30s 23-1/2s 30s 25-1/4s 17-1/2s Construct Solid Bottom Min. 3/8s Plywood Supported by 2 x 4 or 2 x 2 Runners all Four Sides 2s Min. (3s Recommended) 23-1/2s 25-1/4s Per Oven Requirement Construct Solid Bottom Min.
Installation Preparation Preparation WITHOUT an Accessory Storage Drawer PREPARE THE OPENING (cont.) 23-1/2s Installation beside another GE/Monogram Built-in Speedcook Oven: • If you are mounting one Under-the-Counter GE/Monogram oven beside the other, use the dimensions shown. The middle rail separating the two openings may need to be larger than the 4-1/2s minimum shown. 25-1/4s 25-1/4s 17-1/2s 17-1/2s 4-1/2s Min. (5-1/2s Recommended) PREPARE THE OPENING (cont.
Installation Preparation Preparation WITH an Accessory Storage Drawer NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4s. MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL. PREPARE THE OPENING (cont.) PREPARE THE OPENING (cont.) The Advantium 120V can be installed in combination with other GE/Monogram appliances.
Installation Preparation Preparation WITH an Accessory Storage Drawer NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4s. MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL. PREPARE THE OPENING (cont.) PREPARE THE OPENING (cont.) Installation over a GE/Monogram Oven: Installation over a GE/Monogram Oven and Warming Drawer: 30s 23-1/2s 25-1/4s Min.
Installation Preparation Preparation WITH an Accessory Storage Drawer NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4s. MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL. PREPARE THE OPENING (cont.) PREPARE THE OPENING (cont.
Installation Preparation Preparation WITH an Accessory Storage Drawer NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4s. MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL. 23-1/2s PREPARE THE OPENING (cont.
Installation Instructions 2 DOOR TRIM REMOVAL FOR ABOVE 36s INSTALLATION ONLY 3 SLIDE THE OVEN INTO THE CUTOUT If installing the Advantium 120V Oven above 36s from the floor, you may remove the plastic trim from the bottom of the door for esthetic purposes if desired. lift the oven into the opening. Grasp the bottom at front and rear. DO NOT USE THE HANDLE TO LIFT THE OVEN. DAMAGE WILL OCCUR.
Installation Instructions 4 INSTALL BOTTOM TRIM 6 INSTALL MOUNTING SCREWS CAUTION: If installing the Advantium 120V Oven below 36s, you must use the plastic bottom trim due to burn risk to children. The plastic trim acts as insulation and will help prevent burns to children from hot surfaces. PRECAUCIÓN: Si va a instalar el horno Advantium de 120V debajo de 36”, usted debe utilizar el reborde inferior plástico debido al riesgo de quemaduras para los niños.
GE Consumer & Industrial Appliances Assembly Instructions Advantium® Built-In Accessory Storage Drawer JX2200, JX2201, ZX2201 BEFORE YOU BEGIN MODELS AVAILABLE Profile Models: JX2200BB–Black JX2201SS–Stainless Steel Read these instructions completely and carefully. Read the Installation Instructions for the Advantium 120V or 240V oven completely and carefully for cutout dimensions and step-by-step instructions.
ASSEMBLY TO ADVANTIUM BUILT-IN SPEEDCOOK OVEN 1 REMOVE PACKAGING AND PARTS • • • • 3 ASSEMBLING THE OVEN TO DRAWER Remove the drawer from the carton. Remove all packing material and tape. Open the drawer and remove any parts inside. Locate parts. Side Supports (2) A Place storage drawer on a surface with the front of drawer hanging over the edge of the surface.
ASSEMBLY TO ADVANTIUM BUILT-IN SPEEDCOOK OVEN ASSEMBLING THE OVEN TO DRAWER (cont.) C Remove the front two bottom screws on each side of the oven and the top center screw on each side of the storage drawer. D Place the side supports into the tabs on the drawer and secure using the screws supplied and the screws removed in Step C. Side Support 120v only E The oven and storage drawer assembly is now ready to be installed.
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Printed in Korea GE Appliances & Lighting Appliances General Electric Company Louisville, KY 40225 GEAppliances.
