Use and Care Manual

49-5000444 Rev. 2 9
Installation Instructions
INSTALLATION INSTRUCTIONS
How to Install In Pre-Existing Wall
Sleeve
1. Identify the wall-sleeve brand for your installation,
from the chart below.
Wall Sleeve Dimensions (inches)
Width Height Depth
White-Westinghouse
25-1/2 15-1/4 16, 17-1/2 or 22
Frigidaire
Carrier (52F Series)
GE/Hotpoint 26 15-5/8 15-7/8
Whirlpool 25-7/8 16-1/2 17-1/8 or 23
Fedders/Emerson 27 16-3/4 16-3/4 or 19-3/4
Sears/Kenmore
25-3/4 16-7/8 18-5/8
Carrier (51S Series)
Emerson/Fedders 26-3/4 15-3/4 15
Friedrich 27 16-3/4 16-3/4
NOTE: All wall sleeves used to mount the new air
conditioner must be in sound structural condition and
have a rear grille that securely attaches to sleeve, or
rear flange that serves as a stop for the air conditioner.
IMPORTANT: When installation is complete, replacement
XQLW0867KDYHDUHDUZDUGVORSHDVVKRZQ
2. Remove old air conditioner from wall sleeve and
prepare wall sleeve as follows:
Ŷ&OHDQLQWHULRUGRQRWGLVWXUEVHDOV
Ŷ Wall sleeve must be securely fastened in wall
before installing air conditioner. Drive more nails or
screws through sleeve, into wall, if needed.
Ŷ5HSDLUSDLQWLIQHHGHG
3. ,IQRWSUHH[LVWLQJGULOOD´KROHWRDWWDFKWKHVXSSOLHG
grounding wire to the left side of the wall sleeve (see
DSSUR[LPDWHKROHORFDWLRQGLPHQVLRQVLQWKHLOOXVWUDWLRQ
EHORZ8VHWKHWRRWKHGZDVKHUDQGSRLQWHGVFUHZWR
attach one end of the supplied green striped ground
wire to the inside of the wall sleeve. The toothed
washer must be between the eyelet of the wire and the
wall sleeve. BE CAREFUL TO NOT OVERTIGHTEN
THE SCREW. Pull loose end of ground wire out front
of sleeve, and temporarily bend it down and around
lower edge of sleeve. This ground wire will later be
attached to frame of air conditioner once it is installed.
How to Install In Pre-Existing Wall
Sleeve (continued)
4. Prepare the wall sleeve for installation of the new
unit per the following brand instructions.
1 Emerson 15” Deep
2 Fedders 19-3/4” Deep
3 Fedders or Friedrich 16-3/4” Deep
4 GE/Hotpoint 16-7/8” Deep
5 Sears or Carrier (51S Series) 18-5/8” Deep
6 Whirlpool 17-1/8” Deep
7 Whirlpool 23” Deep
8 White-Westinghouse/
Frigidaire/Carrier (52F Series)
16” + 17-1/2” Deep
9 White-Westinghouse/Frigidaire 22” Deep
5. Identify your wall sleeve type and follow the
instructions for that type in the following pages.
IMPORTANT - BEFORE YOU BEGIN
Ŷ7KLVXQLW¶VSHUIRUPDQFHFKDUDFWHULVWLFVUHVXOWIURP
having two rear air intakes.
Ŷ,WLVYHU\LPSRUWDQWWKDWWKHVHLQVWUXFWLRQVDUHIROORZHG
VRWKHXQLWFDQRSHUDWHDWPD[LPXPHIILFLHQF\
Ŷ,IWKLVLVDQH[LVWLQJVOHHYHDQGWKHUHLVDQH[LVWLQJ
rear grille, it may need to be replaced by one that has
been shipped with the unit in the accessory kit. If the
new rear grille is too small for the rear sleeve opening,
use the black plastic grille. Insure it is secured in place
using the included screws, washers and grommets.
FOR INCREASED EFFICIENCY, UTILIZE THE
PROVIDED LOUVERED REAR PANEL
Installation of new grille provided with unit.
5HPRYHWKHH[LVWLQJJULOOH([FHSWLRQ*(´
2. Place the grille, included with the new air
conditioner, towards the rear of the sleeve.
3. Mark through the hole positions.
4. Drill through the sleeves flanges with a 1/8” drill bit.
5. Attach the new grille with self-threading screws
and washers.
,WLV9(5<,03257$17WKDWWKHJULOOHLVSODFHG
H[DFWO\DVVKRZQEHORZ
0RVWGHFRUDWLYHH[WHULRUJULOOHVPD\EHOHIWLQSODFHDV
long as the proper interior air direction grille is installed.
REAR
Wall Sleeve
UNIT
LEVEL
FRONT
to
3
1
3
Max.
1/8
Hole