Full Product Manual

www.graceconstruction.com
For technical assistance call toll free at 866-333-3SBM (3726)
GRACE
®
, Bituthene, Preprufe, Hydroduct and Ripcord are trademarks, registered in the Unites States and/or other countries,
of W. R. Grace & Co.-Conn. This trademark list has been compiled using available published information as of the publication
date of this brochure and may not accurately reect current trademark ownership or status. Grace Construction Products is a
business segment of W. R. Grace & Co.-Conn. © Copyright 2014 W. R. Grace& Co.-Conn. All rights reserved.
We hope the information here will be helpful. It is based on data and knowledge considered to be true and accurate and is
offered for the users’ consideration, investigation and verication, but we do not warrant the results to be obtained. Please
read all statements, recommendations or suggestions in conjunction with our conditions of sale, which apply to all goods
supplied by us. No statement, recommendation or suggestion is intended for any use which would infringe any patent or
copyright. W. R. Grace & Co.–Conn., 62 Whittemore Avenue, Cambridge, MA 02140. In Canada, Grace Canada, Inc., 294
Clements Road, West, Ajax, Ontario, Canada L1S 3C6.
This product may be covered by patents or patents pending. Copyright 2014 W. R. Grace & Co.–Conn.
BIT-220I Printed in U.S.A. 04/14 GCS/PDF
Physical Properties for Bituthene
®
System 4000 Waterproong Membrane
Property Typical Value Test Method
Color Dark gray-black
Thickness
1
⁄
16
in. (1.5 mm) nominal ASTM D3767—method A
Flexibility, 180° bend over 1 in. Unaffected ASTM D1970
(25 mm) mandrel at -25°F (-32°C)
Tensile strength, membrane, die C 325 lbs/in.
2
(2240 kPa) minimum ASTM D412 modied
1
Tensile strength, lm 5,000 lbs/in.
2
(34.5 MPa) minimum ASTM D882 modied
1
Elongation, ultimate failure 300% minimum ASTM D412 modied
1
of rubberized asphalt
Crack cycling at -25°F (-32°C), Unaffected ASTM C836
100 cycles
Lap adhesion at minimum 5 lbs/in. (880 N/m) ASTM D1876 modied
2
application temperature
Peel strength 9 lbs/in. (1576 N/m) ASTM D903 modied
3
Puncture resistance, membrane 50 lbs (222 N) minimum ASTM E154
Resistance to hydrostatic head 231 ft (71 m) of water ASTM D5385
Permeance 0.05 perms (2.9 ng/m
2
sPa) maximum ASTM E96, section 12—water method
Water absorption 0.1% maximum ASTM D570
Footnotes:
1. e test is run at a rate of 2 in. (50 mm) per minute.
2. e test is conducted 15 minutes aer the lap is formed and run at a rate of 2 in. (50 mm) per minute at 40°F (5°C).
3. e 180° peel strength is run at a rate of 12 in. (300 mm) per minute.
Supply
Bituthene
®
System 4000 3 ft x 66.7 ft roll (200 ft
2
) [0.9 m x 20 m (18.6 m
2
)]
Roll weight 83 lbs (38 kg) gross
Palletization 25 rolls per pallet
Storage Store upright in dry conditions below 95°F (+35°C).
System 4000 Surface Conditioner 1 x 0.625 gal (2.3 L) bottle in each roll of System 4000 Membrane
Ancillary Products
Surface Conditioner Sprayer 2 gal (7.6 L) capacity professional grade sprayer with specially engineered nozzle
Bituthene
®
Liquid Membrane 1.5 gal (5.7 L) pail/125 pails per pallet or 4 gal (15.1 L) pail/48 pails per pallet
Preprufe
®
Detail Tape 2 in. x 50 ft (50 mm x 15 m) roll/16 rolls per carton
Bituthene
®
Mastic Twelve 30 oz (0.9 L) tubes/carton or 5 gal (18.9 L) pail/36 pails per pallet
Complementary Material
Hydroduct
®
See separate data sheets
Equipment by others: So broom, utility knife, brush or roller for priming
Physical Properties for Bituthene
®
System 4000 Surface Conditioner
Property Typical Value
Solvent type Water
Flash point >140°F (>60°C)
VOC* content 91 g/L
Application temperature 25°F (-4°C) and above
Freeze thaw stability 5 cycles (minimum)
Freezing point (as packaged) 14°F (-10°C)
Dry time (hours) 1 hour**
* Volatile Organic Compound
** Dry time will vary with weather conditions
90