GBC Quantum P70iX Automated Punch User's Manual Provided By http://www.MyBinding.com http://www.MyBindingBlog.
P70iX Operator Manual US/Canada – 230V 50/60 Hz Assembly Number 7707010 Operator Manual # 7707286 Date Issued October 15, 2003 Revision C-1
Table of Contents Section Safety Information 1. Introduction Introduction Page i 1-1 2. Getting to Know your Quantum P70iX Operating Controls Plastic Covers 2-1 2-2 3. Operation Operating Controls 3-1 4. Options and Accessories Die Set Die Set Storage 4-1 4-2 5. Home Screen Operation Service 5-1 5-1 6. Maintenance Problem solving Paper Jam 6-1 6-2 7.
Safety Information SAFETY MESSAGES The safety of you and others is very important to GBC. Important safety messages and information are contained within this manual as well as on the machine itself. Please be certain to carefully read and understand all of these before operating the machine. ! The safety alert symbol precedes each safety message in this Operating Instruction Manual.
Safety Information SAFETY MESSAGES continued ! WARNING: This means you can be seriously injured by crushing and cutting, moving parts. Do not operate without guards in place. Do not attempt to defeat any of the safety interlock switches. The following symbols appear on this product, and their meaning is as follows: I Means the electrical power is “ON”. O Means the electrical power is “OFF”.
Safety Information IMPORTANT SAFEGUARDS continued • The Quantum P70iX must be connected to a supply voltage corresponding to the electrical rating of the machine operating instructions (also listed on the serial number label). • The socket-outlet shall be located near the equipment and shall be easily accessible. • The grounding plug is a safety feature and will only fit into the proper grounding-type power outlet.
Safety Information MAIN CORDSET SELECTION (THE FOLLOWING NOTE APPLIES ONLY TO EUROPEAN UNITS) ! CAUTION: WHEN CHOOSING A DETACHABLE LINE CORD FOR USE WITH YOUR Quantum P70iX, ALWAYS OBSERVE THE FOLLOWING PRECAUTIONS The cordset consist of three parts; the attachment plug, cordage and appliance inlet. Each of these components must have European regulatory approvals for safety. The following minimum electrical ratings for the specific cordset are published for safety purposes.
Safety Information MAIN CORDSET SELECTION continued (THE FOLLOWING NOTE APPLIES ONLY TO THE U.S. UNITS.) FCC NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
1. Introduction INTRODUCTION The Quantum P70iX is designed to meet the unique requirements of the digital print marketplace. It is designed to support all commonly required punching patterns, including three-hole, comb, VeloBind, Twin-Loop wire, and Color Coil. Custom die patterns are also available. This new system is designed to deliver the quick changeover requirements of the short-run digital printer.
2. Getting to Know your Quantum P70iX GETTING TO KNOW YOUR QUANTUM P70iX External factors can affect performance of your P70iX. These factors include customer requirements for hole quality, throughput materials (paper/transparencies/covers), toner coverage on the printed page, and environmental factors. STATIC in the paper can result in poor performance. If your P70iX runs a fresh ream of clean white paper but has trouble with your printed job, it may be due to static.
2. Getting to Know your Quantum P70iX GETTING TO KNOW YOUR QUANTUM P70iX continued Suggestions for clear plastic covers: The Quantum P70iX is capable of handling and punching some types of clear cover materials. In fact, every Quantum P70iX is tested with clear covers before it leaves the factory. The following guidelines will help you to understand the capabilities of the Quantum P70iX system.
3. Operation OPERATING CONTROLS 2 3 1 1. Ergonomic Workflow: load, unload and program from the same side without any wasted steps. Loading and unloading stack can be safely accomplished while the machine is punching. 1 2. Die Set Changes: are completed without tools and only take seconds to perform. 3. Fully Digital: push button set-up and operation. With simple steps to recall up to 24 custom jobs.
4. Options and Accessories OPTIONS AND ACCESSORIES: Die Sets: The GBC Quantum P70iX Automatic Punch is capable of punching a variety of hole patterns commonly used in binding today, by simply changing the Die Set. Die sets can be changed in seconds without tools. A significant feature of the Quantum P70iX is that it uses GBC Magnapunch Die Sets. Combined with a Magnapunch, you have the capability to switch the Die Set into the punching platform best suited to handle the job in just a matter of minutes.
4. Options and Accessories OPTIONS AND ACCESSORIES continued Die Sets Storage: Helpful Hint: The GBC Die Set Storage Cabinet #7703207 is an excellent way to store all of your interchangeable die sets for the Quantum P70iX (see figure 3). This special product securely holds three die sets, protecting them from dirt, dust, and accidental damage. Contact your sales representative for information on obtaining a Die Set Storage Cabinet. Figure 3 CAUTION: POSSIBLE PINCH POINT HAZARD.
5. Home Screen HOME SCREEN GBC QUANTUM PUNCH 90 LPM 8.5" PB .1 41 7 11" MODE UNLOAD PROOF JOB MANAGER LANGUAGE 1 2 3 4 5 6 7 8 9 0 OK The Home Screen is the starting point for operation of the Quantum P70iX. At this screen, you are able to see the job that the Quantum is ready to run. In the example above, the Quantum is setup to run: • • • • • A paper size of 8.5” x 11” with punching on the 11” side. A lift thickness of “7” which is approximately 7 sheets of 24 pound paper.
5. Home Screen HOME SCREEN continued GBC QUANTUM PUNCH 90 LPM 8.5" PB .1 41 7 11" MODE UNLOAD PROOF JOB MANAGER LANGUAGE 1 2 3 4 5 6 7 8 9 0 OK Other commands from the HOME SCREEN are: MODE: allows you to select between Automatic or Manual. Automatic Mode means the Quantum will continue to run non-stop as long as you place paper on the Input Belts and remove the punched stack of paper from the Output Belts.
5. Home Screen HOME SCREEN continued GBC QUANTUM PUNCH 90 LPM 8.5" PB .1 41 7 11" MODE UNLOAD PROOF JOB MANAGER LANGUAGE 1 2 3 4 5 6 7 8 9 0 OK Other commands from the HOME SCREEN: You have constant control of the Speed by controlling the LPM or Lifts Per Minute and the size of each Lift by adjusting the number of sheets per Lift. Lifts Per Minute (LPM) is controlled by pressing the left – right arrow buttons. You will see the number change in the window.
5. Home Screen JOB MANAGER SCREEN JOB MANAGER — USE ARROWS 3:1RN 10" GO JOB 1 10.5" VIEW 13-24 11 9" 6" 8 297 mm 210mm 8.5" 7 PB141 8" 10 3:1 RN 11" P8094 8" 9 6 11" 4 9.5" PB141 8" 7.5" PB141 11" 3 9" 8.5" GB4:1 5 2 11" ? 8.5" 11" 3-5-7 PB141 12 11" EDITOR ? PB141 8.5" PB141 ? HOME 1 2 3 4 5 6 7 8 9 0 OK At the Job Manager Screen you are able to scroll between saved jobs (1 – 12) by simply pressing the right-left and/or the up/down buttons.
5. Home Screen EDITOR SCREEN EDITOR 0..9 OTHER SIZES GO TO NEXT SETTING NO CHANGE ESCAPE GO BACK DATA OK SAVE STORE ACCEPT ESCAPE SAVE PB .1 41 1 8.5" USE ARROWS TO CHANGE 11" ACCEPT 1 2 3 4 5 6 7 8 9 0 OK To Edit an exiting job or create a new job, press the up – down arrows to select the desired setting. In the example above, the Punch Edge paper dimension has been selected and currently reads 11”. Alternatively, the dimension can be entered directly using the numeric keypad.
5. Home Screen EDITOR SCREEN continued EDITOR 0..9 OTHER SIZES GO TO NEXT SETTING NO CHANGE ESCAPE GO BACK DATA OK SAVE STORE ACCEPT ESCAPE SAVE PB .1 41 1 8.5" USE ARROWS TO CHANGE 11" ACCEPT 1 2 3 4 5 6 7 8 9 0 OK EDITOR SCREEN In the example above, the Side Edge paper dimension has been selected and currently reads 8.5”. Note that the range for this value is 5.50” to 9.00” (139.7 mm to 228.6 mm).
5. Home Screen EDITOR SCREEN continued EDITOR GO TO NEXT SETTING NO CHANGE ESCAPE GO BACK DATA OK SAVE STORE ACCEPT ESCAPE SAVE PB .1 41 1 8.5" USE ARROWS TO CHANGE 11" ACCEPT 1 2 3 4 5 6 7 8 9 0 OK EDITOR SCREEN In the example above, the Punch Die type has been selected and currently reads PB .141. See Table 1 for the Die Sets available for the Quantum. Once all three settings are correct, press the “SAVE” button which will return to the Job Manager Screen.
5. Home Screen “GO JOB” SCREEN EDITOR GO TO NEXT SETTING NO CHANGE ESCAPE GO BACK DATA OK SAVE STORE ACCEPT ESCAPE SAVE PB .1 41 1 8.5" USE ARROWS TO CHANGE 11" ACCEPT 1 2 3 4 5 6 7 8 9 0 OK Selection of a new Die Set will prompt the Die Set screen to come up. This screen will prompt you to remove the proper Punch Pin numbers for the paper size you are running. In the example shown, there are two possible pin configurations with this Die Set and Paper combination.
5. Home Screen RUN SCREEN GBC QUANTUM PUNCH 90 LPM 8.5" PB .1 41 7 11" MODE UNLOAD PROOF JOB MANAGER LANGUAGE 1 2 3 4 5 6 7 8 9 0 OK When the Quantum is running a job, the Graphics will provide you with information about the job that is running. • The example above is telling you that there is paper on the Input Belts and on the Output Belts as well as inside the Quantum processing area.
5. Home Screen SETUP SCREEN GBC QUANTUM PUNCH 90 LPM 8.5" PB .1 41 7 11" MODE UNLOAD JOB MANAGER PROOF LANGUAGE 1 2 3 4 5 6 7 8 9 0 OK When the Quantum is running a job, the Graphics will provide you with information about the job that is running. The example above is telling you that the Die Set is locked. PAUSE verses STOP commands: If you need to stop the system immediately, press “STOP” and the Quantum P70iX will stop in mid-cycle.
6. Maintenance ADDITIONAL INFORMATION SLUG BIN (PAPER CHIP or PAPER CHAD) CONTAINER The slug bin container for your Quantum P70iX is located behind the left hand access door near the bottom of the machine. The container should be periodically pulled out and emptied. This will avoid jamming and damage to the machine. The Quantum P70iX incorporates microprocessor technology to inform the operator when the container needs to be emptied. NOTE: When pull the Slug Bin is pulled out, make sure that it is emptied.
7.
7.
® General Binding Corporation Northbrook, IL 60062-4195 http://www.GBC.com Printed in the U.S.A. Rev.
Guaranteed Lowest Prices on an Endless Selection of Binding Systems, Laminators, Paper Shredders, Supplies and Accessories. We have you covered with Expert Advice and Support. Our popular blog keeps you up to date on the latest tips and techniques to make your most important binding and laminating tasks a success.
