OPERATION MANUAL MBM 207M MANUAL FOLDER 1-800-223-2508 www.mbmcorp.
1
Safety Instructions Definition of Symbols and Notes The following names and signs stand for possible dangers: Danger This symbol stands for immediate danger. Disregarding these instructions may cause severe injury. Caution This symbol stands for a potentially dangerous situation. Disregarding these instructions may lead to injuries or damage to property. Danger Make sure that the machine is electrically grounded to prevent electrical shock. Use the machine at 120 VAC with a frequency of 60Hz.
Introduction Thank you for purchasing the MBM 207M Manual Paper Folder. You should receive many years of reliable service from this machine. Compact and easy to use, the 207M Paper Folder is sure to streamline your paper folding tasks, saving you valuable time. Please read the Operation Manual thoroughly before using this machine. Contents Introduction..................................................................................................................................... 3 Contents ............
(1) Specifications Model 207M Manual Paper Folder Paper size 3.5” × 5” to 11” × 17” Smaller size for single fold only. Paper quality High- to medium-quality paper Fold type Single, Letter, Zigzag, Double Parallel, and Fold-out. Cross-Fold. Maximum Table 1: 13” Table 2: 9 1/2” Fold dimensions Minimum Table 1: 2” Table 2: 1 1/2” Paper feed system Max. stacking capacity Folding speed Three-roller 500 sheets of 20# Bond 10,500 sheets/hr. (8.
(2) Accessories After un-boxing the 207M, make sure that the following accessories are present. Please contact your local dealer immediately if anything is missing.
(3) Description of Parts Stopper plate Number Name Number Name 1 Auxiliary feed table 10 Paper discharge roller 2 Paper guide 11 Paper stacking table 3 Left side cover 12 Control panel 4 Paper feed roller Right side cover 5 Roller cover 13 14 Table 2 6 Table 1 15 Power source switch 7 Fold position adjustment knob 16 Inlet 8 Paper feed table 17 Circuit breaker 9 Paper feed table lever 18 6
(4) Designation and Functions of Operation Panel No. Designation/Indication Function 1 TEST key Performs test folding of two sheets. 2 START/STOP key Starts and stops machine. 3 CLEAR/RESET key Clears the counter / resets after an error. 4 Numerical key Used for Subtraction counting. 5 Counter Indicates the number of sheets folded. 6 Check lamp Comes on when paper stock is depleted, or indicates the location of a mis-feed.
(5) Preparation Install Table 1 and 2: Insert Table 1 on the studs indicated by (a) and (b) as shown in picture. Insert Table 2 on the studs indicated by (c) and (d) as shown in picture. Note: When setting Table 1, be sure to put its stopper plate at the center position. Caution: Be sure that both Table 1 and 2 fit correctly on the studs (a), (b), (c) and (d). If they are improperly set, it may cause an incorrect collation, or the tables may fall out of the machine.
Setting the paper exit roller: The exit roller should be moved to the proper position according to the paper size. Refer to the “Roller Position Indication” label. If ejection is not performed properly, try a different position. Example: Set the roller to position ONE when using 8 1/2” × 11” paper. (6) Operation Procedure Switch the Power to ON: Insert power plug into a proper outlet. Set the POWER switch to the ON position. Note: Remove the power plug from the outlet after use.
Fold Feed Angle / Skew Adjustment: Turn the feed angle adjustment knob to the right if the lower side of the folded paper slants to the right. Turn the knob to the left of the lower side slants to the left. Note: In cases other than single fold, put the folded paper face down on Table 1 to make a feed angle adjustment. Continuous Folding: Press the START/STOP key. The machine will fold the sheets continuously. Press the START/STOP key again while the machine is in operation in order to stop feeding.
Under the following conditions the machine will automatically stop feeding: (Press the CLEAR/RESET key to reset after an error has been corrected) Conditions Indication on Control panel When the START/STOP key is pressed when there is no stock. When the START/STOP key is pressed while the paper feed lever is in the up position. When stock runs out while folding in the Subtraction Counting Mode. When a mis-feed occurs. When paper jam occurs at Table 1 and Table 2. When Roller cover is opened.
Cross Folding: Cross folding refers to performing the double parallel, letter, or other types of folds on single-folded sheets of paper. Example: 11” × 17” sheet is folded in half, and then cross-folded to letter size to fit into a standard # 10 envelope. Note: The maximum weight of paper that can be used for cross folding is 28#.
Fine Adjustments for Table 1 Fold type Single fold Plane (A) Table 1 is not used Long Gate fold Short Long Letter fold Short Long Zigzag fold Short Long Double parallel fold Short Long Fold-out Fold Short 13 Direction to turn the Table 1 fine adjustment knob
Fine Adjustments for Table 2 Fold type Plane (B) Long Single fold Short Long Gate fold Short Long Letter fold Short Long Zigzag fold Short Long Double parallel fold Short Long Fold-out fold Short 14 Direction to turn the Table 2 fine adjustment knob
(7) Maintenance y Keep roller cover closed to prevent dust from accumulating on the rollers. y Clean the rollers regularly using a cleaner suitable for rubber rollers or a cloth slightly dampened with water. Do not use solvents or aerosol sprays. y If paper dust or ink accumulates on the paper rollers or separator, the paper feeding function will deteriorate and may cause a paper jam or slipping. If this happens, clean them using a cleaner suitable for rubber rollers or a cloth slightly dampened with water.
Replacing Paper Separator, Paper Feed Roller & Brake Rubber When replacing the paper feed roller and paper separator, proceed in the order of (1) to (2). Safty cover Paper Feed Roller ② ① Paper Separator Grasp the paper separator (with plastic part) at both ends and pull it out. To install, reverse the procedure. Paper separator To order the parts above, please contact your dealer.
(8) Troubleshooting Trouble The paper does not feed properly The machine does not operate even after the START/STOP key is pressed Possible Cause Measures Recently printed paper sticks together Jog the paper sufficiently. Make sure that the ink is dry. Stains on the paper separator Clean the paper feed separator using appropriate cleaner. Stains on the paper feed rubber roller Clean the dust or ink on the paper feed roller using appropriate cleaner.
18
MBM Corporation 19
