436586 GRILL GAZEBO INSTALLATION MANUAL Base Dimensions 6’10 ½” x 4’11 ¼”; Largest Dimensions 7’10” x 4’11 ¼” 0 ZGP-331.436586 Grill Gazebo.1110-14.GP.
Before Assembly: - Please don't destroy boxes until completely assembled. - Read instructions and check that all parts are present in the boxes. If any parts are missing, refer to warranty information on pg. 9. - Assembly will require at least two persons and 2 hours. - A stepladder will be required for assembly. - The gazebo should be assembled on a level, flat surface. Step 1: Assemble each leg (A, B, C, D) onto base (E) using bolt (U), washer (U-2), and acorn nut (U-1).
Step 3: Attach the rear bars (G) between legs (A & B) using 2 bolts (Z) at each end. Then install the central bar (G-1) at the center of the two rear bars, using bolts (W). 2 ZGP-331.436586 Grill Gazebo.1110-14.GP.
Step 4: Attach the bottom side bars (H) at the bottom between legs (A & C) and (B & D) using bolts (U). Attach the top side bars (I) at the top between legs (A & C) and (B & D) using bolts (Z). Attach the top bars (J) between legs (A & B) and (C & D), again using bolts (Z). 3 ZGP-331.436586 Grill Gazebo.1110-14.GP.
Step 5: Screw shelf brackets (K-1) to the bottom of the shelf (K) on each side, using bolt (Aa) and locknut (Aa-1). Then attach the shelves and shelf brackets between the left legs (A & C) using bolts (Z). Screw cloth holder brackets (L-1 & L-2) to the cloth holder (L) using bolts (Z). Then attach them between the right legs (B & D), also using bolts (Z). Step 6: For the upper roof, lay out edge rafters (M & M-1), two edgings (O), roof panels (P), and rafters (Q), as shown in diagram.
Step 7: Bend and slide roof panel (P) into one corner, then insert rafter (Q) next to it, attaching the ends to the edging (O) with bolts (Cc). Add the next roof panel (P), then another rafter (Q) in the same manner. Insert the final roof panel (P), and then close the upper roof with the previously assembled corner (M & O), using roof connectors (R) at the corners and bolts (Cc).
Step 9: Attach roof supports (S) to the center of each top bar (J) using one bolt (V) each. Attach the lower roof assembly to the roof supports (S) using bolts (W), and to the top of legs (B & D) using 2 bolts (Y) per leg. Attach the upper roof assembly to the plate on lower rafters (N & N-1) using bolts (Z), and to the top of legs (A & C) using 2 bolts (Y) per leg. Step 10: Anchor the unit to the ground through the bases (E).
PART QTY DIAGRAM PART QTY 2 (12-051) BACK LEFT LEG A 1 (14-064) TOP BAR J (12-052) BACK RIGHT LEG B 1 (12-063) LOWER SHELF K 2 (12-053) FRONT LEFT LEG C 1 (12-064) SHELF BRACKET K-1 4 1 (12-065) CLOTH HOLDER L 1 4 (12-066) CLOTH HOLDER BRACKET L-1 1 2 (12-067) CLOTH HOLDER BRACKET L-2 1 2 (12-068) UPPER EDGE RAFTER M 1 2 (12-069) UPPER EDGE RAFTER M-1 1 1 (12-070) LOWER EDGE RAFTER N 1 2 (12-071) LOWER EDGE RAFTER N-1 1 2 (12-072) EDGING O 4 (12-054) FRONT RIGHT LEG D
PART (12-073) 54 ¾” x 19” UPPER ROOF PANEL P (12-074) 48” x 19” LOWER ROOF PANEL P-1 QTY DIAGRAM PART QTY 3 (12-081) BOLT V 2 3 (12-082) BOLT W 4 (12-075) UPPER RAFTER Q 2 (12-083) BOLT X 8 (12-076) LOWER RAFTER Q-1 2 (12-084) BOLT Y 8 (12-077) ROOF CONNECTOR R 8 (12-085) BOLT Z 40 (08-158) BOLT Aa 4 M6x50mm M6x40mm M6x35mm M6x30mm M6x20mm (12-078) ROOF SUPPORT BAR S 2 (12-079) RACK T 1 (12-086) LOCKNUT Aa-1 12 (12-080) HOOK T-1 4 (08-168) BOLT Bb 8 (12-087) BOLT Cc
MAINTENANCE NOTES 1. In case of a defective or damaged part, or for any other questions concerning the product, please contact the manufacturer directly. 2. Please have the parts list and part numbers on hand when ordering or requesting replacement parts. 3. The product should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the roof and cause it to collapse. 4. While the product is designed for 4 seasons use, the roof must be kept free of accumulation of snow.
