43226-22 BROWN 43226-32 SLATE 12’x16’ GAZEBO ASSEMBLY INSTRUCTIONS DO NOT DESTROY THE BOXES UNTIL COMPLETELY ASSEMBLED PLEASE VERIFY THE CONTENT OF EACH BOX AGAINST THE LIST OF PARTS Assembly With Two Or More Adults Recommended Base Dimensions 10’ 11” x 15’6” Largest Dimensions 11’ 11” x 16’2” Overall Height 108.5’’ ZZZ-205.43226.0115-21.GP.EN.doc WEB VERSION APPROX.
DO NOT DESTROY THE BOXES UNTIL COMPLETELY ASSEMBLED PLEASE VERIFY THE CONTENT OF EACH BOX AGAINST THE LIST OF PARTS 12ft x 16ft / 3.65m x 4.88m GAZEBO Instruction Manual IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY Consult with your local governing authority / local municipal codes regarding installation of temporary structures before purchase or assembly. Some jurisdictions may require permits for, or otherwise regulate, installation and use.
MAINTENANCE NOTES 1. In case of a defective or damaged part, or for any other questions concerning the product, please contact the manufacturer directly. 2. Please have the parts list and part numbers on hand when ordering or requesting replacement parts. 3. The product should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the roof and cause it to collapse. 4. While the product is designed to stay assembled year long, the roof must be kept free of accumulation of snow.
Before You Assemble the Gazebo PLEASE DON'T DESTROY BOXES UNTIL COMPLETELY ASSEMBLED Please verify the content of each box against the list of parts. It is important that this gazebo be anchored on a solid base with the provided screws. Otherwise, please ensure that you use anchors sufficient for your surface. The gazebo should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the gazebo and cause it to collapse. Tools required (not provided) 6ft (1.
ZZZ-205.43226.0115-21.GP.EN.
Step 2: 1. For each leg “G”, attach foot plate “H” using 3 bolts “Pp”. Step 3: 1. Unscrew 4 Pp Bolts as shown below, have someone lift the Beam assembly and attach each Leg “G” into a Corner, again securing each using 4 Bolts “Pp”. 2. Repeat until all four Legs are in place. ZZZ-205.43226.0115-21.GP.EN.
Step 4: 1. Install Middle Cover “J” at each of the 4 Beam junctions, using 4 Screws “Qq” each. 2. Install Corner Cover “I” at each of the corners, using 4 Screws “Qq” each. 3. ZZZ-205.43226.0115-21.GP.EN.
Step 5: 1. Attach Mounting Brackets “O” to Rafters “M”, and Mounting Brackets “P” to Rafters “N” and “N2”. Use threaded hole about 8½” & 5” from end of Rafter. 2. Lift Central Hub “L” to a height of about 110” (2.79m) at the center of the gazebo. (Caution: this part may be heavy, use support as needed) 3. Attach one end of Rafter “M” to the Hub using 1 Bolt “Pp”. Attach other end with Mounting Bracket to the corner of the beam assembly with 2 Bolts “Pp”. Use the set of holes closest to the inside.
Step 7: Install the Flashings “Q”, “R”, “S”, and “S-3” onto the beam assembly, using Screws “Qq” on the inside. The notched end of a flashing will always go in a corner of the gazebo. Step 8: Install the Curtain Rails “T” and “U” on the inside of the beam assembly using Bolts “Pp”. Pp ZZZ-205.43226.0115-21.GP.EN.
Step 9: Slide the indicated polycarbonate panels into the spaces between the rafters, using the top groove of each rafter. Ensure the side meant to face the sun is on the outside. Use a rubber hammer to carefully tap each panel into the grooves. Step 10: Insert the middle roof joints in between the rafters and slide them up under the polycarbonate panels. Tap lightly to ensure the panel is fully in the slot. Seen from above, most of the joint as well as the drain holes should be beneath the roof panels.
Step 11: Slide the remaining polycarbonate roof panels in the lower groove of the rafters and into the lower slot of the roof joints. Tap to make sure panels fit securely and do not extend past the ends of the rafters. Step 12: Starting from any end, install all edgings, with End Caps “Gg” or “Hh” at each junction or corner respectively. Use Bolts “Pp” to secure. ZZZ-205.43226.0115-21.GP.EN.
Step 13: Install the upper crossbars on the interior of the roof using Bolts “Pp”, following the shaped ends and letters. Do not tighten bolts immediately; install loose and tighten once all crossbars are in place. Repeat this step with the lower crossbars. Pp Pp Pp Step 14: a) Secure each foot plate into the ground using Screws “Rr” and Washers “Tt”. b) Use Lag Shields (Ss) if needed for harder surfaces. ZZZ-205.43226.0115-21.GP.EN.
Step 15: Install the Screen Curtains “Ww” in the interior groove of the curtain rails, using the provided hooks. Install the Privacy Curtains “Xx” in the exterior groove of the rails. Once the hooks are in, use Curtain Rail Caps “Uu” to close ends of curtain rails. Ww/Xx Note that both curtains are packaged and ordered in sets of 2 panels, each set covering half the gazebo. IMPORTANT NOTES: Make sure all screws and bolts are tight. If conditions are windy, you may have to add cable guides at the corners.
43226 BROWN (see page 19 for Slate parts) PART PACKED IN BOX QTY (11-626-22) 3 2 3 2 3 2 3 2 (11-628-22) CORNER PLATE E 3 4 (11-629-22) CENTER PLATE F 3 4 (11-630-22) 81 ½” LEG G (11-631-22) FOOT PLATE H 2 1 2 4 2 8 2 2 2 4 2 10 2 4 2 4 2 2 2 2 DIAGRAM 85 ½” CENTRAL HUB L 92 5/8” ROOF RAFTER M 73 ¾” ROOF RAFTER N (11-637-22) 91” TOP RIGHT BEAM D QTY (11-708-22) 91” TOP LEFT BEAM C (11-689-22) PACKED IN BOX (11-731-22) 65 ½” TOP RIGHT BEAM B (11-688-22) P
PART PACKED IN BOX PACKED IN BOX QTY 2 4 1 2 1 2 1 2 1 2 2 (11-680-22) 72 5/8” LEFT EDGING, 12’ SIDE Dd 2 2 2 (11-715-22) 72 5/8” RIGHT EDGING, 12’ SIDE Dd-2 2 2 QTY (11-690-22) 88” TOP CAP K 2 1 (11-641-22) 60 ½” CURTAIN RAIL, 12’ SIDE U 2 4 1 2 1 2 1 6 (11-674-22) 31”x38” LEFT UPPER PANEL, 12’ SIDE V (11-711-22) 31”x38” RIGHT UPPER PANEL, 12’ SIDE V-2 (11-734-22) 37”x25 ½” MIDDLE UPPER ROOF PANEL W (11-675-22) 37 ½”x30 ½” RIGHT UPPER PANEL, 16’ SIDE X (11-712-22) 37 ½”x3
PART (11-676-22) 38 ½” LEFT MID ROOF JOINT 12’ SIDE Y (11-713-22) 38 ½” RIGHT MID ROOF JOINT 12’ SIDE Y-2 (11-647-22) 25 ½” CENTER MIDDLE ROOF JOINT Z (11-677-22) 31” RIGHT MID ROOF JOIN 16’ SIDE Aa (11-714-22) 31” LEFT MID ROOF JOINT 16’ SIDE Aa-2 (11-682-22) 43 ¼” LEFT LOWER CROSSBAR 16’ SIDE Ii (11-717-22) 43 ¼” RIGHT LOWER CROSSBAR 16’ SIDE Ii-2 PACKED IN BOX PART PACKED IN BOX QTY 2 (11-652-22) 26 ¾” CENTER EDGING Ee 2 6 2 (11-653-22) 58 7/8” RIGHT EDGING, 16’ SIDE Ff 2 2 6 (11-651-22) 5
PART PACKED IN BOX QTY PART PACKED IN BOX QTY 2 6 (08-167) SCREW Rr 3 12 2 (08-193) PLASTIC PLUG Ss 3 12 2 (08-187) WASHER Tt 3 16 2 (11-697) CURTAIN RAIL CAP Uu 3 8 2 (08-189) ACORN NUT Vv 3 4 DIAGRAM DIAGRAM (11-657-22) 26 ¾” MIDDLE LOWER CROSSBAR Jj (11-683-22) 53 ½” RIGHT LOWER CROSSBAR 12’ SIDE 2 (M6x100mm) Kk (11-718-22) 53 ½” LEFT LOWER CROSSBAR 12’ SIDE 2 (M6) Kk-2 (11-685-22) 20 ½” RIGHT UPPER CROSSBAR1 2’ SIDE 2 Ll (11-720-22) 20 ½” LEFT UPPER CROSSBAR 12’
PACKED PART IN BOX QTY DIAGRAM PART QTY 1 6 3 112 DIAGRAM (11-698) (11-661-22) 17 ½” 38”x25 ½” RIGHT UPPER CROSSBAR 16’ SIDE MIDDLE LOWER ROOF PANEL Yy 2 2 3 1 Nn-2 10 mm KEY PACKED IN BOX (11-705) CURTAIN HOOKS *NOT INCLUDED IN THE BOX DESCRIPTION SPRAY PAINT COLOUR PART # 11-726 BROWN PAINT PEN ZZZ-205.43226.0115-21.GP.EN.
43226 SLATE PART PACKED IN BOX QTY (11-626-32) 3 2 3 2 3 2 3 2 (11-628-32) CORNER PLATE E 3 4 (11-629-32) CENTER PLATE F 3 4 (11-630-32) 81 ½” LEG G (11-631-32) FOOT PLATE H 2 1 2 4 2 8 2 2 2 4 2 10 2 4 2 4 2 2 2 2 DIAGRAM 85 ½” CENTRAL HUB L 92 5/8” ROOF RAFTER M 73 ¾” ROOF RAFTER N (11-637-32) 91” TOP RIGHT BEAM D QTY (11-708-32) 91” TOP LEFT BEAM C (11-689-32) PACKED IN BOX (11-731-32) 65 ½” TOP RIGHT BEAM B (11-688-32) PART (11-691-32) 65 ½” TOP LE
PART PACKED IN BOX PACKED IN BOX QTY 2 4 1 2 1 2 1 2 1 2 2 (11-680-32) 72 5/8” LEFT EDGING, 12’ SIDE Dd 2 2 2 (11-715-32) 72 5/8” RIGHT EDGING, 12’ SIDE Dd-2 2 2 QTY (11-690-32) 88” TOP CAP K 2 1 (11-641-32) 60 ½” CURTAIN RAIL, 12’ SIDE U 2 4 1 2 1 2 1 6 (11-674-32) 31”x38” LEFT UPPER PANEL, 12’ SIDE V (11-711-32) 31”x38” RIGHT UPPER PANEL, 12’ SIDE V-2 (11-734-32) 37”x25 ½” MIDDLE UPPER ROOF PANEL W (11-675-32) 37 ½”x30 ½” RIGHT UPPER PANEL, 16’ SIDE X (11-712-32) 37 ½”x3
PART (11-676-32) 38 ½” LEFT MID ROOF JOINT 12’ SIDE Y (11-713-32) 38 ½” RIGHT MID ROOF JOINT 12’ SIDE Y-2 (11-647-32) 25 ½” CENTER MIDDLE ROOF JOINT Z (11-677-32) 31” RIGHT MID ROOF JOIN 16’ SIDE Aa (11-714-32) 31” LEFT MID ROOF JOINT 16’ SIDE Aa-2 (11-682-32) 43 ¼” LEFT LOWER CROSSBAR 16’ SIDE Ii (11-717-32) 43 ¼” RIGHT LOWER CROSSBAR 16’ SIDE Ii-2 PACKED IN BOX PART PACKED IN BOX QTY 2 (11-652-32) 26 ¾” CENTER EDGING Ee 2 6 2 (11-653-32) 58 7/8” RIGHT EDGING, 16’ SIDE Ff 2 2 6 (11-651-32) 5
PART PACKED IN BOX QTY PART PACKED IN BOX QTY 2 6 (08-167) SCREW Rr 3 12 2 (08-193) PLASTIC PLUG Ss 3 12 2 (08-187) WASHER Tt 3 16 2 (11-697) CURTAIN RAIL CAP Uu 3 8 2 (08-189) ACORN NUT Vv 3 4 DIAGRAM DIAGRAM (11-657-32) 26 ¾” MIDDLE LOWER CROSSBAR Jj (11-683-32) 53 ½” RIGHT LOWER CROSSBAR 12’ SIDE 2 (M6x100mm) Kk (11-718-32) 53 ½” LEFT LOWER CROSSBAR 12’ SIDE 2 (M6) Kk-2 (11-685-32) 20 ½” RIGHT UPPER CROSSBAR1 2’ SIDE 2 Ll (11-720-32) 20 ½” LEFT UPPER CROSSBAR 12’
PACKED PART IN BOX QTY DIAGRAM PART QTY 1 6 3 112 DIAGRAM (11-698) (11-661-32) 17 ½” 38”x25 ½” RIGHT UPPER CROSSBAR 16’ SIDE MIDDLE LOWER ROOF PANEL Yy 2 2 3 1 Nn-2 10 mm KEY PACKED IN BOX (11-705) CURTAIN HOOKS *NOT INCLUDED IN THE BOX DESCRIPTION SPRAY PAINT COLOUR PART # 18-125 SLATE PAINT PEN ZZZ-205.43226.0115-21.GP.EN.
NOTE: The Dimensions Are Approximate. ZZZ-205.43226.0115-21.GP.EN.
