adlonco@hotmail.com 41215-32 12 X 15 SOLARIUM ASSEMBLY INSTRUCTIONS Two or more adults required for assembly Base Dimensions 12’ ½”x15’6”, Largest Dimensions 13’6”x16’11” (see pg.14) Overall Height 110’’ ZZZ-183.41215-32.1127-15.GP.EN.HER.
Before you assemble the Solarium It is important that this solarium be installed on a solid base with the provided screws. Otherwise, please ensure that you use anchors sufficient for your surface. The solarium should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the solarium and cause it to collapse.
12x15 Solarium Assembly Instructions Step 1: Before starting to assemble, please decide where you would like to position the door panels. 1. Stand up two regular frames (A), using two connecting pieces (E) and affix the panels (A) together. 2. Stand up a frame meant to be next to the door (B) and a door frame (D), placing the door frame either on the left or right, then use two connecting pieces (E) to affix the panel and door frame. 3.
Step 2: 1. Slide top door rail (F) into wheels of sliding door. 2. Slide lower door rail (G) into the plastic guide of the sliding door (C). 3. Use bold (Bb) to affix the plastic stoppers (H) one on each end of top door rail (F). 4. Use screw (Oo) to affix upper door rail end caps (Nn) one on each end of top door rail (F). Step 3: Please note the sliding door should be installed from the inside of the solarium. 1.
Step 4: 1. Attach roof rafters (L) to the central hub (N) using bolt (Bb). 2. Use screw (Z) to affix the rafters (L) onto the top of panels going through the metal piece attached to the rafter (L). Note: Rafters must be affixed where panels connect to each other. Step 5: Use the same method to assemble roof rafters (K) for the angled panels. The rafters (K) should be affixed to the mounting bracket using the hole that will be furthest away from the corner of the unit.
Step 6: Use nut (Hh) and washer (Gg) to affix the top cap (M) to the central hub (N). Step 7: First remove the protective layer from the PC roof panels, then insert them (Y, Aa, Ll, Qq) into the roof rafters according to the below drawing instructions. Note: the side that had the protective layer should be face down. K TOP VIEW ZZZ-183.41215-32.1127-15.GP.EN.HER.
Step 8: After inserting the upper PC panels, insert the aluminum middle roof joints (O, P, Q, Pp) into the roof rafters. The below drawing view is from inside the solarium looking up. Note: the drain holes on the aluminum middle roof joints (O, P, Q, Pp) should be at the bottom. Before After Step 9: After the installation on the middle roof joints complete, insert the bottom PC roof panels (Jj, Kk, Mm, Rr) according to below drawing.
Step 10: Once the PC roof is complete, use aluminum edging ( S, U, W, Ss) to surround the edges of PC roof, and using bolt (Bb) and roof joint (R), tighten securely. Step 11: Once the installation of the edging complete, start affixing the roof cross bars (T, V, X, Tt) using bolt (Ff). Affix the top cross bars (Uu) onto the roof rafter (L) using bolt (Ff). ZZZ-183.41215-32.1127-15.GP.EN.HER.
Step 12: Inside each of the panels (A, B), push two plastic plugs (Ii) into the ground, and then screw down the panels using two screws (Ee) for each panels. Special notes: 1. To remove windows (08-219), pull 1 pin out of the lock position and push the frame to the end of the track, then ease the window out of the tracks one side at a time. 2. To remove screening panel, first remove windows, then unscrew the 2 screws at the top corners of the screen frame. 3. Note that this unit is not waterproof.
12X15 Solarium DESCRIPTION QTY DRAWING 08-129-32 REGULAR FRAME 10 2 12 SLIDING DOOR FRAME TOP DOOR RAIL 2 PLASTIC STOPPER H 08-139-32 08-140-32 135° ANGLED 135° ANGLED 8 INSIDE CONNECTOR CONNECTOR I J 08-141-32 08-142-32 8 K ROOF RAFTER 1 N 08-145-32 08-146-32 ROOF JOINT 4 MIDDLE ROOF JOINT O P 08-147-32 08-148-32 MIDDLE ROOF JOINT 8 6 08-178-32 CENTRAL HUB M MIDDLE 4 L 08-179-32 TOP CAP 2 08-138-32 G ROOF RAFTER 2 F 08-137-32 OUTSIDE 2 08-136-32 E DO
DESCRIPTION QTY 4 S DRAWING ROOF CROSS BAR 4 08-152-32 4 U ROOF CROSS BAR 4 V 08-154-32 08-153-32 EDGING QTY T 08-151-32 EDGING DESCRIPTION 08-150-32 08-149-32 EDGING DRAWING 4 W ROOF CROSS BAR 4 X 08-155 (24 ¼”X42 ¼”) TOP ROOF 08-156-32 4 LEFT PANEL SCREW 28 Z Y 08-157 (24 ½”x46 ½”) TOP ROOF CORNER 08-158-32 4 BOLT 54 Bb PANEL Aa 08-165-32 08-161-32 BOLT 12 Cc LATCH 2 SCREW 24 Ee 08-168-32 08-187 18 Ff WASHER 39 Gg 08-189-32 ACORN NUT 2 08-167-32 Dd
DESCRIPTION QTY 08-195 DESCRIPTION 4 LEFT PANEL Jj Kk 08-197 08-198 (24 ¼”x42 ½”) (46 ¼”x43”) 4 BOTTOM ROOF ROOF PANEL RIGHT PANEL Ll Mm 08-134-32 UPPER DOOR RAIL END CAP 4 4 SCREW 4 Oo 08-172 08-170-32 JOINT 4 08-135-32 Nn MIDDLE ROOF DRAWING (46 ¼”x43”) BOTTOM ROOF CORNER PANEL TOP RIGHT QTY 08-196 (47”x47 ½”) BOTTOM ROOF DRAWING (41 ¼”x42 ¼”) 2 TOP ROOF 2 CENTER PANEL Pp Qq 08-171 (41 ¼”x43”) BOTTOM ROOF 08-173-32 2 EDGING 2 Ss CENTER PANEL Rr 08-174-32
AVAILABLE REPLACEMENT PARTS DESCRIPTION DRAWING DESCRIPTION 08-219-32 85-417-S PVC WINDOW ROUND SPLINE (in frame) FOR SCREENING 10-493 11-572-32 PVC WINDOW BOTTOM PLASTIC (replacement PANEL (for wall material only) panels) 85-417-P ROUND SPLINE FOR PVC WINDOW 11-822-32 BOTTOM PLASTIC PANEL (for doors) 15-123-32 15-097-32 PIN FOR PVC DOOR WHEEL WINDOW ASSEMBLY 13-033 PC WINDOW (for sliding door) 10-458 REPLACEMENT WEATHERSTRIP 124” 12-046-32 15-124-32 MOSQUITO MOUNTING SCREEN
ZZZ-183.41215-32.1127-15.GP.EN.HER.
MAINTENANCE NOTES 1. In case of a defective or damaged part, or for any other questions concerning the product, please contact the manufacturer directly. 2. Please have the parts list and part numbers on hand when ordering or requesting replacement parts. 3. The product should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the roof and cause it to collapse. 4. While the product is designed for 4 seasons use, the roof must be kept free of accumulation of snow.
