adlonco@hotmail.com 41212-12 12 X 12 SOLARIUM ASSEMBLY INSTRUCTIONS Two or more adults required for assembly Base Dimensions 12’ ½’’x12’ ½’’, Largest Dimensions 13’6’’x13’6’’ (see pg.14) Overall Height 110’’ ZZZ-182.41212-12.1030-15.GP.EN.
Before you assemble the Solarium Please don't destroy boxes until completely assembled. It is important that this solarium be installed on a solid base with the provided screws. Otherwise, please ensure that you use anchors sufficient for your surface. The solarium should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the solarium and cause it to collapse.
12x12 Solarium Assembly Instructions Step 1: Before starting to assemble, please decide where you would like to position the door panels. 1. Stand up the two panels (A), using two connecting pieces (E) affix the panels (A) together. 2. Stand up a frame meant to be next to the door (B) and a door frame (D), you can chose to place the door frame on the left side or on the right side, and then use two connecting pieces (E) to affix the panel and door frame. 3.
Step 2: 1. Slide top door rail (F) into wheels of sliding door (C). 2. Slide lower door rail (G) into the plastic guide of the sliding door(C). 3. Use bolt (Bb) to affix the plastic stoppers (H) one on each end of top door rail (F). 4. Use screw (Oo) to affix upper door rail end caps (Nn) one on each end of top door rail (F). Step 3: Please note the sliding door should be installed from the inside of the solarium. 1.
Step 4: 1. Attach roof rafters (L) to the central hub (N) using bolt (Bb). (Caution: hub may be heavy, use support if needed. 2. Use screw (Z) to affix the rafters (L) onto the top of panels going through the metal piece attached to the rafter (L). Rafters must be affixed where panels connect to each other. (2) (2) Step 5: Use the same method to assemble roof rafters (K) for the angled panels.
Step 6: Use nut (Hh) and washer (Gg) to affix the top cap (M) to the central hub (N). Step 7: First remove the protective layer from the PC roof panels, then insert them (Y, Aa, Ll) into the roof rafters according to the below drawing instructions. Note: the side that had the protective layer should face down. TOP VIEW ZZZ-182.41212-12.1030-15.GP.EN.
Step 8: After inserting the PC roof panels, insert the aluminum middle roof joints (O, P, Q) into the roof rafters. The below drawing view is from the inside of the solarium, looking up. Note: the drain holes on the aluminum middle roof joints (O, P, Q) should be at the bottom. Before After Step 9: Insert the outer PC roof panels (Jj, Kk, Mm) according to below drawing. They should overlap about two inches under the upper PC roof panels and into the aluminum middle roof joints.
Step 10: Once the PC roof is complete, use aluminum edging (S, U, W) to surround the edges of the PC roof using bolts (Bb) to fasten the rafter cap (R) and the edging, tighten securely. Step 11: Use the cross bars (T, V, X) to affix to the roof using bolts (Ff). ZZZ-182.41212-12.1030-15.GP.EN.
Step 12: Inside each of the panels (A, B), push two plastic plugs (Ii) into the ground, and then screw down the panels using two screws (Ee) for each panel. Special notes: 1. To remove windows (08-219), pull 1 pin out of the lock position and push the frame to the end of the track, then ease the window out of the tracks one side at a time. 2. To remove screening panel, first remove windows, then unscrew the 2 screws at the top corners of the screen frame. (2) (1) ZZZ-182.41212-12.1030-15.GP.EN.
12X12 Solarium DESCRIPTION QTY 08-129-12 REGULAR FRAME 8 2 FRAME NEXT TO DOOR SLIDING DOOR FRAME 8 E TOP DOOR RAIL F 08-137-12 08-138-12 BOTTOM 2 G PLASTIC STOPPER 4 H Length 206 cm 08-139-12 08-140-12 135° ANGLED 135° ANGLED 8 INSIDE CONNECTOR I J Length 200.6 cm Length 200.6 cm 08-141-12 08-142-12 ROOF RAFTER ROOF RAFTER 8 L Length 239.7 cm Length 211 cm 08-143-12 08-144-12 TOP CAP 2 Length 206 cm Length 200.
DESCRIPTION QTY 08-145-12 MIDDLE ROOF JOINT DRAWING DESCRIPTION 4 MIDDLE ROOF JOINT P 08-147-12 08-148-12 JOINT 4 Q S 4 4 Length 94.5 cm 08-152-12 ROOF CROSS 4 BAR 4 V Length 94.4 cm 08-154-12 08-153-12 W BAR T Length 120.6 cm EDGING 12 ROOF CROSS 08-151-12 U CAP 08-150-12 Length 120.6 cm EDGING ROOF RAFTER 4 R 08-149-12 EDGING DRAWING 08-146-12 O MIDDLE ROOF QTY ROOF CROSS 4 BAR 4 X Length 120.6 cm Length 94.
DESCRIPTION QTY 12 Cc 2 LATCH 08-168-12 RIGHT DOOR LATCH SCREW 12 WASHER 08-189-12 08-193 1 PLASTIC PLUG Hh Ii 08-195 08-196 (47” X47 ½”) (46 ½”x43”) 4 BOTTOM ROOF CORNER PANEL LEFT PANEL Jj Kk 08-197 08-198 (24 ¼” X42 ¼”) TOP ROOF 4 RIGHT PANEL Ll Mm 08-134-12 RAIL END CAP 20 4 4 08-135-12 4 SCREW 4 Oo Nn 12-037-12 FEMALE BOLT 39 (46 ½”x43”) BOTTOM ROOF RIGHT PANEL UPPER DOOR 20 08-187 Gg BOTTOM ROOF 2 08-167-12 Ff ACORN NUT DRAWING Ee Dd-L BOLT QTY
AVAILABLE REPLACEMENT PARTS DESCRIPTION 08-219-12 DRAWING DESCRIPTION 85-417-S PVC WINDOW ROUND SPLINE (in frame) FOR SCREENING 10-493 11-572-12 PVC WINDOW BOTTOM PLASTIC (replacement PANEL (for wall material only) panels) 85-417-P ROUND SPLINE FOR PVC WINDOW 11-822-12 BOTTOM PLASTIC PANEL (for doors) 15-123-12 15-097-12 PIN FOR PVC DOOR WHEEL WINDOW ASSEMBLY 13-033 PC WINDOW (for sliding door) 10-458 REPLACEMENT WEATHERSTRIP 124” 12-046-12 15-124-12 MOSQUITO MOUNTING SCREEN
ZZZ-182.41212-12.1030-15.GP.EN.
MAINTENANCE NOTES 1. In case of a defective or damaged part, or for any other questions concerning the product, please contact the manufacturer directly. 2. Please have the parts list and part numbers on hand when ordering or requesting replacement parts. 3. The product should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the roof and cause it to collapse. 4. While the product is designed for 4 seasons use, the roof must be kept free of accumulation of snow.
